ページ1に含まれる内容の要旨
BeoLab 7-1
BeoLab 7-2
Guide
ページ2に含まれる内容の要旨
Cautions! – Make sure that the loudspeaker is placed and connected in accordance with the instructions in this Guide. – Do not attempt to open the loud- CAUTION: To reduce the risk of speaker. Leave such operations electric shock, do not remove to qualified service personnel! cover (or back). – The loudspeaker is designed for No User-serviceable parts inside. indoor use in dry, domestic Refer servicing to qualified environments only, and for use service personnel. within a temperat
ページ3に含まれる内容の要旨
Daily use 3 When you have finished setting Cleaning the loudspeaker up the loudspeaker as described Clean dusty surfaces using a dry, on the following pages, connect soft cloth. If necessary, remove the entire system to the mains. grease stains or persistent dirt with Caution: Handle the loudspeaker a lint-free, firmly wrung cloth, front grill with great care. Dents Loudspeaker protection dipped in a solution of water and scratches are not covered by The loudspeaker is equipped with a conta
ページ4に含まれる内容の要旨
Set up the loudspeaker 4 We recommend that you follow ‘Type 1 bracket’ this procedure: 100 cm 39" – Disconnect your Bang & Olufsen system from the mains. – Mount the loudspeaker to the BeoLab 7-1 Bang & Olufsen stand or wall bracket as explained on the next page. ‘Type 2 bracket’ 124 cm – Connect the loudspeaker as 49" explained in ‘Cable connections’ (pp. 6–7). – Set the POSITION switch to the BeoLab 7-2 correct setting. This is explained in ‘Adapt the loudspeaker to your roo
ページ5に含まれる内容の要旨
5 Here is shown how to fasten the loudspeaker with a ‘type 1 bracket’ to a Bang & Olufsen ‘single-column’ stand (or wall bracket). Use the same procedure if you wish to fasten a the loudspeaker to a Bang & Olufsen ‘double-column’ Stand c – with a ‘type 2 bracket’. a Remove the small cover (if any) on the stand. Press the cover as shown, and it will come loose. b Fasten the bracket to the stand or wall bracket. Use the two longest screws (M5 × 25 mm) – four screws for a ‘type 2 bra
ページ6に含まれる内容の要旨
Cable connections 6 The loudspeaker is primarily intended to be used in a setup with BeoVision 7*. It may, how- Mains connection ever, be used with other Bang & to BeoVision 7 Olufsen systems as well – for POWER LINK example in a BeoVision 4 setup. socket If used in a setup not including POSITION switch Cable clamp BeoVision 7, you will require a mains cord and a Power Link cable. These cables are available The socket panel is located on the rear of the loudspeaker. as optional a
ページ7に含まれる内容の要旨
7 Connection to BeoVision 7 … BeoVision 7 Connect the loudspeaker to one of the Power Link sockets on the left BeoVision 7 socket panel. For further information about the BeoVision 7 socket panels, refer to the Guides enclosed with the product. Cable clamp: For safety reasons, the mains cord from the wall outlet must be secured to the loudspeaker. To do so, tug the cord behind the clamp. BeoLab 7 The two mains cords and the Power Link cable are enclosed with BeoVision 7. Connect
ページ8に含まれる内容の要旨
Adapt the loudspeaker to your room 8 When a loudspeaker is placed The POSITION switch in a corner or close to a wall, the bass level is boosted • F (Free-standing position) compared to the bass level from Use this setting if the loudspeaker a loudspeaker placed in a more is placed so that the front grill is free-standing position. more than 50 cm (20") from the F W rear wall, for example on one of To remove this excessive bass the floor or table stands. boost, use the POSITION switch to
ページ9に含まれる内容の要旨
9 The POSITION switch is located on the loudspeaker socket panel. F W How to measure … The distance is measured as shown here – the loudspeaker seen from above.
ページ10に含まれる内容の要旨
10 To get access to the approval labels, remove the loudspeaker front grill: Push the front grill towards the left (~ 10 mm). The front grill can now be removed. Caution: Handle the loudspeaker Note: When attaching the front front grill with great care. Dents grill again, make sure that all five and scratches are not covered by ‘attach-points’ engage with the the guarantee! corresponding brackets on the loud- speaker. Do not attempt to mount the front grill upside down (marked on the
ページ11に含まれる内容の要旨
For the Canadian market only! This product fulfils the For the US-market only! This class B digital apparatus meets conditions stated in the NOTE: This equipment has been all requirements of the Canadian EEU directives 89/336 and 73/23. tested and found to comply with Interference-Causing Equipment the limits for a class B digital device, Regulations. Technical specifications, features pursuant to part 15 of the FCC Rules. and the use thereof are subject to These limits are designed to prov
ページ12に含まれる内容の要旨
www.bang-olufsen.com
