ページ1に含まれる内容の要旨
HP NetServer
Fibre Channel Host Bus
Adapter Installation Guide
HP Part Number 5971-0825
Printed in November 2000
ページ2に含まれる内容の要旨
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Hewlett-Packard assumes no responsibility for
ページ3に含まれる内容の要旨
Contents 1 Introduction............................................................................... 1 Audience for this Manual...................................................................................... 1 What is the Hewlett-Packard Fibre Channel Adapter? ......................................... 1 Contents of the Fibre Channel Adapter Kits ......................................................... 1 What Is Needed Besides the Adapter .................................................
ページ4に含まれる内容の要旨
5 NetWare Driver Loading ......................................................... 17 Overview ............................................................................................................. 17 Driver Loading on an Existing NetWare Server .................................................. 17 Unloading the Driver ...........................................................................................19 Updating the Driver ..........................................................
ページ5に含まれる内容の要旨
Third-Party Hardware Products ...................................................................... 40 HP Repair and Telephone Support .................................................................... 40 U.S. and Canada ............................................................................................ 40 Other Countries .............................................................................................. 40 World Wide Web ...................................................
ページ6に含まれる内容の要旨
vi
ページ7に含まれる内容の要旨
1 Introduction Audience for this Manual This guide is intended for network administrators, maintenance engineers or qualified personnel who maintain and/or update servers. Since installing this Adapter involves both hardware and software installation functions, it is important that the person installing the adapter is familiar with performing such tasks as installing PCI cards, connecting cables, and installing software drivers. What is the Hewlett-Packard Fibre Channel Adapter? The Hewlett-Pack
ページ8に含まれる内容の要旨
Fibre Channel Host Bus Adapter (HBA) A Hewlett-Packard Navigator CD containing the available adapter driver(s) A documentation CD containing the Fibre Channel Host Bus Adapter Installation Guide This installation guide What Is Needed Besides the Adapter Besides the Fibre Channel HBA, you will need the following: A GBIC module supported by the Fibre Channel HBA A fibre channel cable, either optical or copper A fibre channel device (such as the Fibre Channel Hub) to connect to the GB
ページ9に含まれる内容の要旨
Figure 1-1. 32/64 bit PCI, 33 MHz PCI, 1 Gbit The HP Fibre Channel Adapter installs into a standard PCI (Peripheral Component Interconnect) slot. This adapter supports a high performance 64-bit PCI bus (backward compatible to 32-bit) with multiplexed address and data lines, and parity information. The PCI bus provides a high speed (up to 264/132 Megabytes/sec) path between the system board and the Fibre Channel Adapter. The HP Fibre Channel Adapter is a PCI Bus Master device and conforms to the
ページ10に含まれる内容の要旨
System Requirements Windows NT Systems The following items are required when you install the HP Fibre Channel Adapter into a Windows NT system: A Pentium or higher system with PCI local bus Windows NT 4.0 installed with at least service pack 4 Minimum recommended system memory is 32 MBytes Windows 2000 Systems The following items are required when you install the HP Fibre Channel Adapter into a Windows 2000 system: A Pentium or higher system with PCI local bus Windows 2000 RTM installe
ページ11に含まれる内容の要旨
2 Installation Overview Before installing the Adapter in your server, make sure that the system is powered down and that you follow ESD procedures to reduce the risk of damage to the Adapter or the server electronics. See Appendix A regarding ESD information. Installing Adapter in PCI Slot Install the Adapter in any standard PCI slot. The following generalized installation steps pertain to most PCI installations. Most system chassis are either vertical or horizontal orientated, therefore, you sh
ページ12に含まれる内容の要旨
Figure 2-1. Installing Adapter GBIC Overview A GBIC converts internal electrical signals to external electrical or optical signals for transmission across the Fibre Channel media. The Fibre Channel cable inserts into the connector of the GBIC module. There are several types of GBIC modules currently available that can be used in the D8602B Fibre Channel Adapter. GBICs are “hot pluggable,” which means they can be plugged into, or pulled out of the Adapter while the power is applied. CAUTION Do no
ページ13に含まれる内容の要旨
CAUTION Inserting a passive GBIC without Fibre Channel device/ hub attached will cause an open loop condition. This open loop condition will prevent devices attached to the internal HSSDC connector from functioning. To avoid this situation, avoid inserting the passive GBIC until external Fibre Channel devices are attached to the passive GBIC. Installing the GBIC Select the type of GBIC module that is compatible with your system. Install the GBIC into the receptacle on the Adapter. Refer to Fig
ページ14に含まれる内容の要旨
Connecting Cables 1. If you are using an optical GBIC module, remove the dust plug covers protecting the optical connectors before inserting the fibre-channel cable. Save the dust plug covers for future use. 2. Select the correct cable that matches the GBIC you installed and install the end connectors into the GBIC. The GBIC and Fibre Channel cable are keyed, so they can only fit one way. Refer to Figure 2-3. on page 8 for optical cable connection and Figure 2-4. on page 9 for copper cable conne
ページ15に含まれる内容の要旨
Figure 2-4. Copper Cable Connector Removing the GBIC To remove the GBIC, follow these steps: 1. Remove the Fibre Channel cable. (a) If you are using the HSSDC Copper Cable, squeeze the tab to remove. (See Figure 2-6. on page 10.) 2. (a) If you are using an optical GBIC, flip the bar of the GBIC to the “OPEN” position and pull to remove. (See Figure 2-5. on page 10.) (b) If you are using the HSSDC Copper GBIC, squeeze the tabs on both sides of the GBIC. (See Figure 2-6. on page 10.) 3. Pull the m
ページ16に含まれる内容の要旨
Figure 2-5. Removing the Optical GBIC Module Figure 2-6. Removing the HSSDC Copper GBIC Module Verifying the Adapter You can verify the Adapter and cable installation by powering up the system and looking at the two LEDs on the bulkhead of the adapter. See Figure 2-7. on page 11. Under normal operation, the LEDs operate as follows: 10
ページ17に含まれる内容の要旨
Upon Power-up: PWR / ACT LED is ON LINK LED is OFF During Card initialization by the Host OS: PWR / ACT LED will flash as Fibre Channel devices are identified LINK LED is OFF Once the card has been initialized by the Host OS: PWR / ACT LED will flash at approximately 1 second intervals LINK LED is on if the link is up Figure 2-7. Adapter LEDs 11
ページ18に含まれる内容の要旨
12
ページ19に含まれる内容の要旨
3 Windows NTDriver Installation NOTE Check this worldwide web address to ensure that you have the latest version of the Windows NT driver: http://netserver.hp.com/netserver/ If it is a newer version than the one on the supplied HP Navigator CD, download it and use it instead of the earlier driver. Overview Before installing the Fibre Channel Adapter driver, the Windows NT system should be up and running. The HP Navigator CD contains the fibre channel HBA drivers. You need to create a driver disk
ページ20に含まれる内容の要旨
4. From the Settings menu, select Control Panel. 5. From the Control Panel window, select SCSI Adapters. 6. From the SCSI Adapter window, select Drivers. 7. From the Drivers window, select Add. 8. Select Have Disk. 9. From the floppy disk drive (path, A:\WINNT), select Agilent PCI Fibre Channel Controller (NT 4.0). 10. Press OK. 11. When the installation is complete, remove the diskette, shut down Windows NT, and reboot the system to load the driver. Removing the Driver In certain situations you
