ページ1に含まれる内容の要旨
®
HS3000/HS3020
High-Security
Enclosures
Installation/
Operation Manual
C483M-E (9/97)
Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • www.pelco.com
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120
ページ2に含まれる内容の要旨
CONTENTS Section Page 1.0 GENERAL ..................................................................................................1 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ...............................1 1.2 UNPACKING INSTRUCTIONS ..........................................................2 1.3 RECOMMENDED TOOLS .................................................................2 2.0 DESCRIPTION ..........................................................................................3 2.1 MODELS
ページ3に含まれる内容の要旨
1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 3. Only use replacement parts recommended by Pelco
ページ4に含まれる内容の要旨
1.2 UNPACKING INSTRUCTIONS Unpack and inspect all parts carefully. The following parts are supplied: 1 Camera enclosure 1 1/4"-drive socket for tamper-resistant screws 1 7/64" Allen wrench 2 1/4-20 x 1/2" bolts 2 1/4" flat washers 2 1/4" split lock washers Be sure to save the shipping carton and any inserts. They are the safest material in which to make future shipments. If an item appears to have been damaged in shipment, replace it properly in its carton and contact the factory at 1-800-289-9
ページ5に含まれる内容の要旨
2.0 DESCRIPTION The HS3000 Series is a high security camera enclosure designed for installations such as ATM bank machines, prisons, detention cells, etc., requiring maximum protection from vandalism. In addition, a factory-installed tamper switch is mounted on the secured access cover. Constructed from heavy-gauge steel, the HS3000 Series will accept most CCD cameras with fixed focal length lenses ranging in size from 4mm to 75mm. There is no exposed mounting hardware securing the HS3000 Serie
ページ6に含まれる内容の要旨
3.0 INSTALLATION Before installing the HS3000/HS3020 to a wall or ceiling, make certain that the mounting surface is able to support four times the full load of the enclosure plus all other equipment such as camera, lens, etc. To mount the enclosure to a wall or ceiling, follow the steps outlined below. 1. Unscrew the screws and remove the cover using the special socket (fits 1/4" drive) and Allen wrench that are provided. 2. Knock out any of the three (3) cable entry holes desired on the enclo
ページ7に含まれる内容の要旨
Table A. Video Coaxial Cable Wiring Distances Cable Type* Maximum Distance RG59 750 ft (229 m) RG6 1,000 ft (305 m) RG11 1,500 ft (457 m) * Minimum cable requirements: 75 ohms impedance All-copper center conductor All-copper braided shield with 95% braid coverage Table B. 24 VAC Wiring Distances The following are the recommended maximum distances for 24 VAC applications and are calculated with a 10-percent voltage drop. (10-percent is generally the maximum allowable voltage drop for AC-powered
ページ8に含まれる内容の要旨
4.0 MAINTENANCE Regularly scheduled maintenance will help prolong the operational life and appear- ance of the equipment. Clean the plexiglass viewing window regularly with a soft cloth, using a mild, non- abrasive detergent and water solution to help maintain picture clarity. 6 Pelco Manual C483M-E (9/97)
ページ9に含まれる内容の要旨
5.0 EXPLODED ASSEMBLY DRAWING Figure 1. HS3000/HS3020 Exploded Assembly Drawing Table C. HS3000/HS3020 Exploded Assembly Parts List Item Quantity Description Part Number 11 Window, Lexan™, smoked AH300010005 21 Body (HS3000) AH30001000WA (HS3020) HS30201000WA 32 End plate gasket AH300010015 41 Cover (HS3000) AH30004002COMP (HS3020) HS30204002COMP 52 Tilt table AH30004004COMP 61 Rear plate AH30004005COMP 71 Tilt table lock plate AH30004006COMP 82 Tamper-resistant screw ZH1/4-20X.50SRT 91 Socke
ページ10に含まれる内容の要旨
6.0 SPECIFICATIONS MECHANICAL Window: 1/4" (.63 cm) thick, impact and abrasion resistant smoked Lexan™ (1 f-stop attenuation) Camera Mounting: Adjustable tilt table Enclosure Mounting: Four (4) .390" (.99 cm) diameter holes on protected rear surface Maximum Camera/Lens Size Accepts camera/lens combinations (including BNC connector) up to: HS3000 3.75" H x 3.25" W x 9.00" L (9.52 cm x 8.25 cm x 22.86 cm) HS3020 3.75" H x 3.25" W x 18.00" L (9.52 cm x 8.25 cm x 45.72 cm) Security: Tamper-resistan
ページ11に含まれる内容の要旨
Figure 2. HS3000/HS3020 Dimension Drawing Pelco Manual C483M-E (9/97) 9
ページ12に含まれる内容の要旨
7.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. ® • Three years on Genex Series products (multiplexers, server, and keyboard). ® • Three years on Camclosure and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, M
