ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
TABLE OF CONTENTS ABOUT THIS GUIDE...........................................................3 1. INTRODUCTION ..............................................................4 FEATURES AND BENEFITS .........................................................5 UNPACKING THE PACKAGE .......................................................7 SYSTEM REQUIREMENT.............................................................8 PHYSICAL DESCRIPTION........................................................
ページ3に含まれる内容の要旨
WEB CONFIGURATION UTILITY...............................................19 SYSTEM ADMINISTRATION......................................................21 VIEWING VIDEO ......................................................................46 6. IPVIEW SE........................................................................50 INSTALLATION.........................................................................50 GETTING STARTED ..............................................................
ページ4に含まれる内容の要旨
ABOUT THIS GUIDE This manual provides instructions and illustrations on how to use your Pan/Tilt Internet Camera, includes: Chapter 1, Introduction, provides the general information on the camera. Chapter 2, Hardware Installation, describes the hardware installation procedure for the camera. Chapter 3, Security, explains the security feature of the camera. Chapter 4, Application of the Camera, provides the illustrations of the camera’s applications. Chapter 5, Using the Camera, g
ページ5に含まれる内容の要旨
1 INTRODUCTION Thank you for purchasing the Pan/Tilt Internet Camera, a standalone system that can be connected directly to an Ethernet or Fast Ethernet. Compared to the conventional PC camera, the Pan/Tilt Internet Camera features a built-in CPU and web-based solutions that can provide a cost-effective solution to transmit the real-time high-quality video images for monitoring. The camera can be managed remotely, so that you can use a web browser to access and control it from any not
ページ6に含まれる内容の要旨
Features and Benefits Simple To Use The Pan/Tilt Internet Camera is a standalone system with built-in CPU, no special hardware (such as a PC frame capture card) or software required. The camera supports DirectX 9.0; therefore, the only requirement you need is the web browser software such as Internet Explorer 5.0 or above. Once you have a valid IP Address, just connect it and you can view the picture from your camera. In addition, the camera’s pan/tilt function allows you to adjust t
ページ7に含まれる内容の要旨
Remote Utility The powerful IPView SE application assigns the administrator with a pre-defined user ID and password, allowing the administrator to modify the camera settings from the remote site via Intranet or Internet. When new firmware is available, you can also upgrade remotely over the network for added convenience. Users are also allowed to monitor the image, and take snapshots. Broad Range of Applications With today’s high-speed Internet services, the camera can provide the i
ページ8に含まれる内容の要旨
Unpacking the Package Unpack the package and check all the items carefully. In addition to this User’s Guide, be certain that you have: One Pan/Tilt Internet Camera One External Power Adapter (5V DC, 2A) One RJ-45 Ethernet Cable One Metal Clip One Multi-Language Quick Installation Guide One Installation CD-ROM If any item contained is damaged or missing, please contact your local dealer immediately. Also, keep the box and packing materials in case you need to ship the uni
ページ9に含まれる内容の要旨
System Requirement Networking Local Area Network: 10Base-T Ethernet or 100Base-TX Fast Ethernet Accessing the Camera For Web Browser Users Operating System: Microsoft® Windows® 98SE/ME/ 2000/XP CPU: Intel Pentium II, 266 MHz or above Memory Size: 128MB (256MB recommended) Resolution: 800x600 or above Microsoft® Internet Explorer 5.0 or above For IPView SE Application Users Operating System: Microsoft® Windows® 98SE/ME/ 2000/XP. CPU: Intel Pentium III, 450 MHz or above
ページ10に含まれる内容の要旨
Physical Description This section describes the externally components’ features of your camera. Front Panel There are two LED indicators on the front panel of the camera: Power LED and Link LED. 1. Power LED The Power LED is positioned on the right side of the two LEDs. A steady BLUE light confirms that the camera is powered on. 2. Link LED The Link LED is positioned on the left side of the two LEDs. A steady ORANGE light confirms that the camera has good connection to
ページ11に含まれる内容の要旨
Rear Panel 1 DC Power Connector 2 Reset Button 3 Network Cable Connector 1. DC Power Connector The DC power input connector is located on the camera’s rear panel, and is labeled DC5V 2.5A with a single jack socket to supply power to the camera. Power will be generated when the power supply is connected to a wall outlet. 2. Reset Button Reset will be initiated when the reset button is pressed once, and Power LED begins to flash. Factory Reset will be initiated when the reset
ページ12に含まれる内容の要旨
2 HARDWARE INSTALLATION Attaching the Metal Clip Wall screw Scre w Ceiling screw Screw Wall screw Ceiling screw Base of the camera To attach the metal clip, remove the two rubber pads under the base of the camera firstly. Place the metal clip onto the camera base, and align the two holes of metal clip with two screw holes on the base. Secure the metal clip to the base with two screws (provided). Then, you can: 1. Install the camera to the ceiling using two ceiling scr
ページ13に含まれる内容の要旨
Connecting the Ethernet cable Connect an Ethernet cable to the network cable connector located on the camera’s rear panel, and then attach it to the network. Attaching the Power Supply Attach the external power supply to the DC power input connector located on camera’s rear panel, and then connect it to your local power supply. TIP: You can confirm power source is supplied from the Power LED on the camera is illuminated. 12
ページ14に含まれる内容の要旨
3 SECURITY To ensure the highest security and prevent unauthorized usage of the camera the Administrator has the exclusive privilege to access the System Administration for settings and control requirements to allow users the level of entry and authorize the privileges for all users. The camera supports multi-level password protection and access to the camera is strictly restricted to defined the user who has a “User Name” and “User Password” that is assigned by the Administrator. Th
ページ15に含まれる内容の要旨
4 APPLICATION OF THE CAMERA The camera can be applied in wide variety of applications. With the built-in CPU, it can work as a standalone system that provides a web-based solution transmitting high quality video images and sounds for monitoring purposes. It can be managed remotely, accessed and controlled from any PC desktop over the Intranet or Internet via a web browser. With the easy installation procedure, real-time live images will be available. In addition, once the camera
ページ16に含まれる内容の要旨
Applications Monitoring of local and remote places and objects such as construction sites, hospitals, amusement parks, schools and day-care centers through the use of a web browser. Capture single frame images from the IPView SE application. Configure the camera to upload image or send-mail messages with a single frame image. 15
ページ17に含まれる内容の要旨
Application Diagrams of the Camera Home Applications 16
ページ18に含まれる内容の要旨
SOHO Applications 17
ページ19に含まれる内容の要旨
Enterprise Applications 18
ページ20に含まれる内容の要旨
5 USING THE CAMERA You can access and manage the camera through: 1) a web browser, and 2) the enclosed software IPView SE. This chapter describes the Web Configuration Utility, and provides the instructions on using the camera with a web browser. Web Configuration Utility The camera must be configured through its built-in Web-based Configuration. (Extensive knowledge of LAN will be helpful in setting up the camera.) From the web browser, enter the default IP address to access the
