ページ1に含まれる内容の要旨
EV-7105-NPEQ (NTSC)
EV-7105-PPEQ (PAL)
Mini PTZ Camera
Manual
• 10x Optical zoom and 10x digital zoom • Up to 127 preset target views, each
• Up to 100x zoom with its own characteristics such as
white balance and auto exposure
• Up to 360°/sec pan/tilt motion
• Up to 95° tilt, up to 180° with auto-flip
• Outdoor or indoor use
Note: Model numbers that end with “Q” or products that have a round green “Q” sticker signify R
ページ2に含まれる内容の要旨
ENFORCER Mini PTZ Camera a Table of Contents Table of Contents Introduction 2 SYSTEM INFORMATION Menu 18 Features and Functions 3 DISPLAY SETUP Menu 19 Parts List 4 SET NORTH DIRECTION Menu 19 Specifications 4 PRIVACY ZONE Menu 20 Dimensions 5 EDIT MASK Menu 20 Safeguards and Precautions 6 DOME CAMERA SETUP Menu 21 Overview 7 ZOOM CAMERA SETUP Menu 22 Communication Protocol and Camera ID 8 WB SETUP Menu (White Balance) 22 Installation 9 AE SETUP
ページ3に含まれる内容の要旨
ENFORCER Mini PTZ Camera ENFORCER Mini PTZ Camera Features and Functions EV-7105-NPE PTZ Camera Features and Functions 1 1 Powerful yet flexible camera: / -inch CCD camera with Day and Night function, up to 100X zoom (max. 10X Powerful and Flexible: The ENFORCE4R Mini PTZ Camera is equipped with a /4-inch CCD, a powerful Day and Night optical zoom and 10X digital zoom), multiple focus modes, and full programmability. function, up to 100x zoom (max. 10x optical zoom and 10x di
ページ4に含まれる内容の要旨
ENFORCER Mini PTZ Camera a Parts L ist: 1x Camera 4x Short screws (for attaching camera to bracket) Video Signal System NTSC PAL 1x Wall-mount bracket 4x Long screws (for attaching bracket to wall) 1 Camera CCD / ” Interline Tansfer CCD 4 1x Manual 1x Extension cord Max. Pixels 811(H) x 508(V) 410K 795(H) x 596(V) 470K Effective Pixels 768(H) x 494(V) 380K 752(H) x 582(V) 440K Horizontal Resolution 500 TV Lines (Color), 570 TV Lines (B/W) Specifications: S/N Ration 50 dB (AGC Of
ページ5に含まれる内容の要旨
ENFORCER Mini PTZ Camera Dimensions: Camera Side Bottom 6” (152mm) 7” (180mm) 13 4 /16” (122mm) Wall-Mount Bracket Side Bottom 1 3 /8” (80mm) 11 4 / ” 16 (119mm) 1 6 /2” (166mm) SECO-LARM, U.S.A., INC. 5
ページ6に含まれる内容の要旨
ENFORCER Mini PTZ Camera Safeguards and Precautions Before Starting: 1. Please read this manual carefully and keep it for future reference. 2. Use the camera within given temperature and electrical limits. 3. Do not point the camera at the sun. Heat could damage the camera, even when not in use. 4. Do not expose the camera to rain or moisture. 5. Do not install the camera in dusty or humid environments. 6. Do not mount the camera in areas exposed to radiation, strong m
ページ7に含まれる内容の要旨
ENFORCER Mini PTZ Camera a Overview Wall mount bracket Camera DIP switches Lens Turn counter-clockwise to remove Dome SECO-LARM, U.S.A., INC. 7
ページ8に含まれる内容の要旨
ENFORCER Mini PTZ Camera a Com munication Protocol and Camera ID DIP Switch Setup: Before the Mini PTZ Camera is installed, first set up the DIP switches to configure the camera ID and the communications protocol. Communication Protocol Camera ID 1. Remove the clear dome of the Mini PTZ Camera by turning it counterclockwise by hand. 2. Look for the two DIP switch blocks near the base of the black plastic dome which surrounds the camera. DO
ページ9に含まれる内容の要旨
ENFORCER Mini PTZ Camera a Installation 1. Connect the camera to either the included wall mount or other optional bracket. 2. Run a 24VAC power supply wire, a video cable with a male BNC connector, and a data wire through the wall to where the camera is to be mounted. 3. Connect the camera's video cable to the video cable coming from the wall. Do not cut the female BNC connector of the camera's video cable as that will void the warranty. 4. Connect the camera's RS-485 ca
ページ10に含まれる内容の要旨
ENFORCER Mini PTZ Camera a Pre-operation Checklist Before operating this PTZ camera, please note the following: Double-check that the cables are properly run between the controller and camera, and that all connections are correct. Double-check that the camera ID on the controller is the same as the ID of the target camera. The camera ID can be found by looking at the camera ID DIP switch settings (see page 8). The Pelco protocol setting of the controller and the
ページ11に含まれる内容の要旨
ENFORCER Mini PTZ Camera Understanding and Operating Preset and Pattern Functions Standard Pelco-compatible controllers allow the camera operator to do several functions without going through the full OSD menu, depending on the capabilities of the DVR to which the camera is connected. The SECO-LARM series of DVRs allows operators to do the following via the "Dome Preset" menu: • Set the camera to remember multiple specific preset locations. • Tell the camera to go to a
ページ12に含まれる内容の要旨
ENFORCER Mini PTZ Camera Configuring Mini PTZ Camera settings with an ENFORCER DR-1 Series DVR Step 1 Press Dome on the DVR front panel to access DVR controls. Step 2 Press 1 to access the DVR preset menu Step 3 Use the Up, Down, Left, Right, and Enter buttons to make a selection. Step 4 Go to Preset 95 to access Mini PTZ OSD settings. This will bring up the SPEED DOME C
ページ13に含まれる内容の要旨
ENFORCER Mini PTZ Camera Reserved Presets [95] :Enters into OSD menu [131~134] :Runs Pattern Function 1~4 [141~148] :Runs Swing Function 1~8 [151~158] :Runs Group Function 1~ 8 [170] :Sets Camera BLC mode to OFF [171] :Sets Camera BLC mode to ON [174] :Sets Camera Focus mode to AUTO [175] :Sets Camera Focus mode to MANUAL :Sets Camera Focus mode to [176] SEMI-AUTO
ページ14に含まれる内容の要旨
ENFORCER Mini PTZ Camera OSD Display of Main Screen Preset Action Title Label Alarm Image Flip Information Camera ID Pan/Tilt/Zoom Information OSD Main Screen The OSD main screen shows information about the current situation of the camera while it is operating. This screen is NOT seen as part of the programming process. Preset Label The label of the specific preset. Will be one of the following: SET PRESET XXX When PR
ページ15に含まれる内容の要旨
ENFORCER Mini PTZ Camera Operating the OSD Menus For operating the OSD menus, please note the following: • To access the OSD menu from your DVR, go to Preset 95. For more information on DVR presets and their functions for the ENFORCER Mini PTZ Camera, please see page 13, Reserved Presets. • Most commands are done on PELCO-compatible DVRs using the front panel keys, including the up, down, right, and left arrows, or via a panel-mounted joystick. Such operations may
ページ16に含まれる内容の要旨
ENFORCER Mini PTZ Camera ENFORCER Mini PTZ Camera OSD (On-screen Display) and Programming Flowchart This chart shows all the screens used in programming the PTZ camera using the OSD. OSD Main Screen To go to a particular screen, follow the order as shown in this flowchart. (page 14) For more information on a particular screen, go to the page number listed on the screen. SPEED DOME CAMERA (page 18) SYSTEM DISPLAY DOME CAMERA SYSTEM INFORMATION SETUP SETUP INITIALIZE (p
ページ17に含まれる内容の要旨
ENFORCER Mini PTZ Camera SPEED DOME CAMERA Menu SPEED DOME CAMERA • : Displays system information and configuration (see menu on page 18). • : Configures the display information shown on the OSD Main Screen as shown on page 16 (see menu on page 19). EXIT • : Configures various functions of the camera (see menu on page 21).
ページ18に含まれる内容の要旨
ENFORCER Mini PTZ Camera DISPLAY SETUP Menu From SPEED DOME CAMERA DISPLAY SETUP This menu enables or disables the information shown on the OSD Main Screen (see page 14). CAMERA ID : ON PTZ INFORMATION : AUTO ACTION TITLE : AUTO Note that setting an item to "AUTO" means that item will be PRESET LABEL : AUTO displayed only when its value changes. ALARM INPUT : AUTO This menu accesses other OSD menus for configuring a specific B
ページ19に含まれる内容の要旨
ENFORCER Mini PTZ Camera PRIVACY ZONE Menu From DISPLAY SETUP PRIVACY ZONE This menu configures an area of the camera’s field of vision so that it is covered by a gray mask, hiding it. For instance, this MASK NO 1 would be used to cover a neighbor’s window, or a sensitive UNDEFINED DISPLAY OFF window of the office. CLEAR MASK CANCEL Once configured, the gray mask automatically appears over that area every time the camera pans or tilts past it. BACK EX
ページ20に含まれる内容の要旨
ENFORCER Mini PTZ Camera DOME CAMERA SETUP Menu From SPEED DOME CAMERA Goes to the ZOOM CAMERA SETUP menu DOME CAMERA SETUP for configuring many of the general functions of the zoom camera module. See page 22. Configures the general functions of the pan and tilt motions. See page 24 Configures up to 127 different preset locations to which t
