ページ1に含まれる内容の要旨
SNC-B5368(P)
Network Camera
User Manual
imagine the possibilities
Thanks you for purchasing this Samsung product.
To receive a more complete service, please visit
our website
www.samsungsecurity.com
RoHS compliant
Our product complies with “The Restriction Of the use of certain Hazardous Substances in electrical
and electronic equipment”, and we do not use the 6 hazardous materials- Cadmium (Cd), Lead
+6
(Pb), Mercury (Hg), Hexavalent Chromium (Cr ), Poly Brominated Biphenyls (PBBs), Poly Bro
ページ2に含まれる内容の要旨
overview CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. WARNING To reduce the risk of fi re or electri
ページ3に含まれる内容の要旨
● OVERVIEW 7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or electric shock. 8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fi re or electric shock. 9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG i
ページ4に含まれる内容の要旨
overview FCC STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation. Caution This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection
ページ5に含まれる内容の要旨
● OVERVIEW IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi ers) that produce heat. 9. Do not defeat the safety purpose of th
ページ6に含まれる内容の要旨
overview CONTENTS 5 Important Safety Instructions OVERVIEW 8 Product Features 8 Recommended PC Specifi cations 9 What’s Included 2 10 At a Glance 14 Removing the Covers INSTALLATION & CONNECTION 15 Connecting with other Device 17 Installation 14 20 How to use the Keyboard CAMERA SETUP Controller 21 Main Menu 21 Profi le 20 22 Camera Setup 26 Privacy Zone 27 Others 28 System Info 28 Language 29 Connecting the Camera to an NETWORK CONNECTION IP Router with the xDSL/Cable AND SETUP Modem 30 Conne
ページ7に含まれる内容の要旨
● OVERVIEW 40 Connecting to the Camera WEB VIEWER 41 Login 42 Installing ActiveX 43 Using the Live Screen 40 44 Backup 46 Accessing the Setup Screen SETUP SCREEN 47 Default Setup 51 System Setup 54 Overlay Setup 46 55 Event Setup 60 Network Setup 62 Profi le APPENDIX 63 Terminology 64 Specifi cations 68 Frame Rate (NTSC) 62 74 Frame Rate (PAL) 80 Troubleshooting English _7
ページ8に含まれる内容の要旨
overview PRODUCT FEATURES Support various communication protocols Supports TCP/IP, UDP, RTP/RTSP, SMTP for email, and FTP protocols as well as various internet protocols such as ARP, HTTP, HTTPS and DHCP. Web Browser-based Monitoring Using the Internet web browser to display the image in a local network environment. Automatic Local IP Setup Even a network novice can install it with minimum operations. Alarm If the camera equipped with an alarm sensor senses any motion, it will send a notifi
ページ9に含まれる内容の要旨
● OVERVIEW WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. User Manual/ Camera User Manual IP INSTALLER CD Test Monitor Cable Screw The Test Monitor Cable is connected to a portable displayer and used for testing the camera. M If you intend to use it for an actual monitoring camera, use the BNC cable instead. English _9
ページ10に含まれる内容の要旨
overview AT A GLANCE Appearance Item Description Dome Cover Case cover used to protect the lens and the main unit. Main Unit Consists of: lens, switch board, PCB and screws. Power Port Used to plug in the power cable. Used to connect the Video In connector of the monitor, from which the video Video Output Port signal of the camera outputs. Network Port Used to connect the PoE or LAN cable. Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied M eth
ページ11に含まれる内容の要旨
● OVERVIEW Inside Item Description Consists of two different ports: - ALARM IN : Used to receive the alarm input signal. Alarm I/O Port - ALARM OUT : Used to output the alarm output signal. - GND : Used for earth-grounding. Restores all camera settings to the factory default. Press and hold it for about 3 seconds to turn off the system indicator and restart the system. Reset Button J After resetting the camera, you must run the IP Installer program to change the basic network settings su
ページ12に含まれる内容の要旨
overview Components 1 3 2 Lens 6 4 5 7 8 9 12_ overview
ページ13に含まれる内容の要旨
● OVERVIEW Item Description Inner Cover Cover used to protect the main unit. Wing-Side Hook Tap on either end to remove the inner cover. The Test Monitor Cable is connected to a portable displayer and used for Monitor Out testing the camera. Zoom Lever Used to adjust or fix the zoom factor of the lens. Focus Lever Turn it to the left or right to adjust the focus; turn it clockwise to fix the focus. Tilt Screw Used to adjust or fix the tilt of the lens. Bracket Used to install the camera on the
ページ14に含まれる内容の要旨
installation & connection REMOVING THE COVERS If you want to connect the Alarm I/O connectors, you must remove the dome cover and lens cover beforehand. 1. Turn the dome cover counter-clockwise. 2. Remove the dome cover by lifting it up. 3. Tap on either end of the lens cover to remove it. 14_ installation & connection
ページ15に含まれる内容の要旨
● INSTALLATION & CONNECTION CONNECTING WITH OTHER DEVICE Power Monitor Network Power Supply Connect the power adaptor to the power input port. Be careful not to reverse the polarity when you connect the power cable. J You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera. Connecting to the monitor Connect the [V_OUT] port of the camera to the video input port of the monitor. Network Connection Connect the Network cable to the local network or to the Inter
ページ16に含まれる内容の要旨
installation & connection Connecting to the I/O port box Connect the Alarm I/O cable to the corresponding port of the inner port box. ALARM IN GND ALARM OUT ALARM IN 1, 2 : Used to connect the alarm input signal. GND : Used for earth-grounding. ALARM OUT 1, 2 : Used to connect the alarm output signal. Alarm I/O Wiring Diagram ALARM IN 1 1 ALARM IN 2 2 GND 3 External Relay ALARM OUT 1 4 External Relay ALARM OUT 2 5 16_ installation & connection
ページ17に含まれる内容の要旨
● INSTALLATION & CONNECTION INSTALLATION Precautions before installation Ensure you read out the following instructions before installing the camera: Select an installation site (ceiling or wall) that can endure at least 5 times of the camera weight. Stuck-in or peeled-off cables can cause damage to the product or a fire. For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case. Installing the camera 1. Hold down t
ページ18に含まれる内容の要旨
installation & connection 4. Use the provided screws (x3) to fi x the bracket to a desired position (ceiling or wall). Ensure that the label on the bracket faces the direction for camera monitoring. Upper Lid 5. Arrange the cables through the bracket to the ceiling or wall. Press hard the upper lid down to remove it before you can arrange the cables through to the ceiling. If you do not intend to install the camera on the ceiling, use the opposite empty area to the
ページ19に含まれる内容の要旨
● INSTALLATION & CONNECTION Adjusting the monitoring direction for the camera Panning Tilting Lens rotation You can adjust the camera direction only when the camera is fixed on the ceiling. Then, turning the camera to the left or right is referred to as "Panning", while tilting the angle is "Tilting". For panning, the panning limit is 220˚ for the clockwise, and 120˚ for the counter- clockwise, a total of 340˚ enabled; further rotation is stopped by the stopper. English _19
ページ20に含まれる内容の要旨
camera setup You can configure the camera settings using the Web Viewer. For accessing the Web Viewer, refer to "Network Connection and Setup". (page 29) M HOW TO USE THE KEYBOARD CONTROLLER Follow the steps below if you run the Web Viewer for setting the menus. 1. Launch the Web Viewer. 2. From the [Camera OSD] menu in the left pane, click [Menu]. The screen appears. 3. Click the Up/Down (▲▼) buttons to move to a desired item. ▲▼◄ ► 4. Click the four direction ( ) buttons to nav