ページ1に含まれる内容の要旨
INSTALLATION/OPERATION
CCC5100H Series
SIMD Digital
Color Camera
C2910M-C (4/06)
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Description . . . . . . . . . . . . . .
ページ4に含まれる内容の要旨
Auto White Balance (AWB) Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Predefined Profile Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ5に含まれる内容の要旨
List of Illustrations 1 CCC5100H Series Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2 DC-Drive Auto Iris Lens Connections (Camera Connector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3 Mounting Lens to Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ6に含まれる内容の要旨
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de
ページ7に含まれる内容の要旨
Description The CCC5100H Series camera is a high resolution, 480 TV line, wide dynamic range video camera with a 1/3-inch SIMD imager. It automatically senses and sets the video standard to NTSC or PAL. It supports DC-drive auto iris lenses as well as C- and CS-mount lenses. The CCC5100H ® Series camera also automatically supports Coaxitron as well as the Pelco D and Pelco P protocols. Using its setup menus, it offers a wider range of options and settings than other cameras. The CCC
ページ8に含まれる内容の要旨
PARTS LIST CCC5100H Series camera Quick Start Guide Two-pin terminal block Four-pin auto iris connector Lens mount cap Resource CD: • Installation/Operation manual: INSTALL.PDF • Quick Start Guide: QSG.PDF • Important Safety Instructions: SAFETY.PDF OPTIONAL ACCESSORIES PCM150 Adjustable camera mount CST150 Handheld camera setup tool with microdisplay CST100 Handheld camera setup tool with video output connector 8 C2910M-C (4/06)
ページ9に含まれる内容の要旨
Lens Mounting The CCC5100H Series camera supports both manual and DC-drive auto iris lenses, either fixed focal length or varifocal. The camera accepts both CS- and C-mount lenses without a mount adapter. NOTE: The CCC5100H Series camera does not support video-drive auto iris lenses. WIRING AN AUTO IRIS LENS DC-drive auto iris lenses are controlled through the four-pin drive connector (type D4-152N). Figure 2 identifies the pin connections for the auto iris lens connector o
ページ10に含まれる内容の要旨
Camera Mounting The CCC5100H Series camera can be mounted from either the top or bottom, depending on the type of camera mount used in your installation. Use a standard 1/4-20 screw (provided) with a maximum thread length of 0.375 inch (10 mm). WARNING: The maximum thread depth is 0.4 inch (1 cm). Do not use a longer screw or you may damage the camera. The optional Pelco PCM150 camera mount is designed specifically for CCC5100H Series cameras. It can be used to wi
ページ11に含まれる内容の要旨
Power, Video, and Control Connections The CCC5100H Series is a low voltage camera. Maximum power consumption is about 4.5 watts. The CCC5100H Series camera offers standard power and coax video connectors as well as a multifunction connector that combines power, video (coax and unshielded twisted pair), and control leads for quick installation (refer to Using the Multifunction Connector for more information). Before installation, identify how you will con
ページ12に含まれる内容の要旨
USING COAX VIDEO The CCC5100H Series camera outputs coax video from either the BNC connector on the rear panel or through the multifunction connector. The camera also supports two Pelco up-the-coax technologies. Selected Pelco multiplexers and switchers send a Pelco V-Sync signal to the camera. The camera uses this signal to lock its vertical synchronization pulse to all other connected cameras. This eliminates certain display problems at the head-end. Pelco Coaxitron lets you acces
ページ13に含まれる内容の要旨
USING THE MULTIFUNCTION CONNECTOR The CCC5100H Series camera combines data, video, and power leads into a single multifunction connector on the rear panel. This lets you quickly install and uninstall the camera. NOTES: • Do not connect a network cable into the multifunction connector on the camera’s rear panel. It is not a network connector. • The PCM150 camera mount is designed for the CCC5100H Series camera. It includes a preconfigured cable and an easy-to-wire adapt
ページ14に含まれる内容の要旨
CONTROL LEADS The CCC5100H Series camera lets you access and configure the menu settings from any Pelco keyboard, receiver, or other device that supports the Pelco D or Pelco P protocol. The camera supports the following settings: • Baud rate: 2400, 4800, 9600 • Start bit: 1 • Data bits: 8 • Stop bit: 1 • Parity: None When connecting external control, the wiring should meet the following requirements: 2 2 • 24 AWG (0.25 mm ) or 22 AWG (0.35 mm ) • Shielded tw
ページ15に含まれる内容の要旨
UNSHIELDED TWISTED PAIR (UTP) LEADS The CCC5100H Series camera supports composite video over unshielded twisted pair (UTP) cabling. The camera UTP video output signal is 1 Vp-p differential into a 100-ohm load. At a minimum, UTP requires Cat5, 100-ohm twisted pair cable. You can install either a passive or an active UTP receiver at the head-end. Table F lists the maximum UTP wiring distances. It also lists the restrictions when using either type of UTP recei
ページ16に含まれる内容の要旨
Setup Menus The CCC5100H Series camera uses setup menus instead of hardware switches for configuring the camera. As a result, you have more options for customizing the camera for its specific application. NOTE: After you customize any aspect of the CCC5100H Series camera, be sure to save your custom settings into one of the two user-definable profiles: CUSTOM1 or CUSTOM2. Next, change the default to the saved profile so the camera will automatically load the custom settings at power-up. (
ページ17に含まれる内容の要旨
MAIN MENU EXIT LIGHT METER WHITE BALANCE PROFILES SYSTEM INFORMATION MODE ATW NORMAL ACTIVE ZONE ZONE 2 ACTIVE WDR FIRMWARE VER. SAVE AS CUSTOM1 1.3-X.X.XX EDIT ZONE 1 EDIT ZONE 2 DEFAULT WDR OSD VER. X.XX.X EDIT ZONE 3 BACK RESTART CAMERA EDIT ZONE 4 BACK EXIT RESTORE FACTORY SETTINGS
ページ18に含まれる内容の要旨
ACCESSING THE SETUP MENUS (REAR PANEL) You can access and navigate the setup menus from the top, center, and bottom buttons on the rear panel (refer to Figure 6). TOP CENTER BOTTOM Figure 6. Rear Panel Buttons These buttons respond differently to short and long presses. A short press is less than one second; a long press is more than one second. Table I lists the button presses for each menu action. Table I. Rear Panel Buttons and Actions MENU ACTION BUTTON ACTION Enter setup menus.
ページ19に含まれる内容の要旨
ACCESSING THE SETUP MENUS (PELCO CONTROLLER) USING PRESET 95 You can use preset 95 to access and navigate the setup menus from various Pelco controllers. Use the instructions for your controller to access the main menu. NOTE: CCC5100H Series camera operation has been verified for the following Pelco controllers. CM6700/CM6800 1. Enter the camera number and press the CAM key. 2. Enter 95 and hold the PRESET key for two seconds. A menu screen appears. 3. Move the joystick down to highlight SET. 4
ページ20に含まれる内容の要旨
NAVIGATING THE SETUP MENUS As soon as you access the MAIN MENU, move the joystick up or down to select a menu option. Table J lists the buttons and actions for menu navigation. Table J. Pelco Controller Buttons and Actions MENU ACTION BUTTON ACTION Up or right in menu or item options. Single Move joystick up. Repeat Hold joystick up. Down or left in menu or item options. Single Move joystick down. Repeat Hold joystick down. Select menu or item, or advance to next step. Press iris open. Save set
