ページ1に含まれる内容の要旨
EverFocus
Operation Instruction
IR Day/Night plus Wide
IR Day/Night plus Wide
Dynamic Range IP66 Bullet
Dynamic Range IP66 Bullet
Camera
Camera
EZ650
EZ650
ページ2に含まれる内容の要旨
EVERFOCUS ELECTRONICS CORPORATION P/N: 4605XZ0650001AR Operation Instruction 2008 EverFocus Electronics Corp Please read this manual first for correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. Al
ページ3に含まれる内容の要旨
Precautions 1. Do not place any object on top of the cover. 2. Be careful when handling the camera, do not drop it or subject it to strong shock or vibration to prevent any damages to it. Do not disassemble it or place it on an unstable base. 3. Install the camera away from TV, radio transmitter, magnet, electric motor, transformer, audio speakers because the magnetic fields generate from above devices will distort the video image. 4. Install the camera away from stoves, or other heat gene
ページ4に含まれる内容の要旨
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu
ページ5に含まれる内容の要旨
Table of Contents 1.1 FEATURES.......................................................................................................................................... 6 1.2 ACCESSORY PARTS LIST .............................................................................................................. 7 1.3 SPECIFICATIONS ............................................................................................................................. 8 1.4 DIMENSIONS .........................
ページ6に含まれる内容の要旨
Chapter 1 1. Product Overview Achieve long range surveillance with clarity in virtually any lighting conditions. The amazing low light sensitivity of 0.05 lux before the added benefits of advanced DSP technology, delivered by a 1/3” Sony Super HAD CCD II sensor, is just the beginning with the new EverFocus EZ650. A 6-50mm varifocal auto-iris lens combined with high output IR illuminators delivers a useful range of over 80m/261ft.Mount the optional EIR100 auxiliary illuminator and incre
ページ7に含まれる内容の要旨
Motion detection for 4 configurable zones. Privacy mask function for 8 configurable zones. Provides digital zoom up to 32x. Cables routed through weatherproof bushing in the bracket to prevent vandalism or other damage. IP66 weather resistant. Operating temperature range -40°C to 50°C/ -40°F to 122°F, with thermostatically controlled heater Vandal resistant. 1.2 Accessory Parts List Please be careful when you unpack the box due to the electronics devices inside. Chec
ページ8に含まれる内容の要旨
1.3 Specifications Product Model EZ650 Pickup Device 1/3” SONY Super HAD CCD Ⅱ Video Format NTSC or PAL Picture Elements 768 x 494 (NTSC)/752 x 582 (PAL) Horizontal Resolution 560 TV Lines Sensitivity 0.05Lux/F=1.2(AGC ON); 0.0002Lux/F=1.2 (IR off ,Sens-up 256x Max; ~8X recommened) 0 Lux (IR On) S/N Ratio Over 52dB (AGC off) Electronic Shutter 256x, 128x, ….1/50 (1/60) ~1/100,000 Video Output BNC 1.0V p-p 75 Ω, Gamma Correction 0.45 Lens Type DC Iris Varifocal : 6~50mm focal le
ページ9に含まれる内容の要旨
1.4 Dimensions Drilling Dimension of holes to holes 45mm/1.8” 80mm/3.2” Dimension of Bracket 220.5mm/8.68” 84mm/3.31” 106.5mm/4.19 112.7mm/4.44 199mm/7.83” 9
ページ10に含まれる内容の要旨
Dimension of whole camera with bracket 275mm/10.8” 107.5mm/4.3” 243.5mm/9.74” 357mm/14” Dimension of whole camera with bracket and EPR100 10
ページ11に含まれる内容の要旨
1.5 Camera Component Description Sun shield Fixing screw for sunshield Bracket Power connector RS485 terminal Video output Control key selection switch Control key EZ650 Component description 11
ページ12に含まれる内容の要旨
485- 485+ GND 12VDC 1.6 Back Panel Layout 24VAC model (for 24VAC 110V~240VAC model (for Power Only) 110V ~240V Power only) 2 2 1 1 4 4 3 3 5 5 6 6 7 7 1. Video Output Connector Connect the video output of the camera to a color monitor or other video devices through a 75 Ohm type coaxial cable with BNC female connector at backside of the camera. 2. Power Input Terminal Connect the appropriate power to
ページ13に含まれる内容の要旨
5. Control key selection switch Switch to OSD to control OSD menu by using the control key or switch to LENS to adjust zooming and focus (please see “2.3.1 Lens setting” and “3. OSD Menu & Configuration” for details). Note: when it is connected to RS485 for keyboard control, please switch to OSD, otherwise it cannot be controlled remotely. 6. Control key For setting Lens & OSD menu. 7. Cable clips Used to fix power cable and RS485 cable. 1.7 Related Products In additio
ページ14に含まれる内容の要旨
Chapter 2 2. Installation This chapter will describe, in general terms, how to install the EZ650 camera. STEPS: 1. Wire and mount the camera. See 2.1 2. Adjust the camera position. See 2.2 3. Adjust Lens. See 2.3 4. Connect to Keyboard (Optional) See 2.4 Warning To prevent electrical shock, turn off the electrical power before making electrical connections. Do not expose the appliance to water or moisture, nor try to operate it in wet areas. 2.1 Wiring and Mounting
ページ15に含まれる内容の要旨
2. Fix the bracket to wall by using 4 screws. Coaxial cable Power cable RS485 cable 3. Open camera’s back cover: Loose the 2 screws from the back panel cover, then open the back cover. Screws for back panel 14
ページ16に含まれる内容の要旨
4. Take off the cap of waterproof conduit which is at the camera bottom. Power cable ( Φ10.3mm) Coaxial cable RS485 ( Φ6mm) ( Φ5mm) Note: 1. the holes of waterproof conduit were plugged, please remove the plug when you need to use it for connection. 5. Take coaxial cable, power cable and RS485 cable to pass through waterproof conduit, place them into camera housing. Note: Do not connect BNC connector to coaxial cable until coaxial cable has passed through ca
ページ17に含まれる内容の要旨
Coaxial cable Power cable RS485 cable Note: 1. Power cable’s diameter must be less than 10 mm 2. Only use RG59/5C2V for Video cable 3. RS485 cable must be less then 5 mm 6. Close the waterproof cap and fix waterproof conduit to the base of camera firmly. 7. Fix the camera body to bracket by using the 4 shorter screws. 16
ページ18に含まれる内容の要旨
8. Connect RG59 coaxial cable with BNC connector. 9. Unscrew both cable clips, wire power cable and RS485 cable through the cable clips. Then, screw the cable clips to rear panel. a. Connecting Power-24VAC model: connect 24VAC power on N and L 100VAC~240VAC Model: Connect PE, N and L. *Warning* To prevent electrical shock, turn off the electrical power before making electrical connections. Do not connect high voltage power to the camer
ページ19に含まれる内容の要旨
Screws for back panel 2.2 Adjusting Camera Position Adjust camera’s angle vertically or horizontally by using hex key included in package. Loose this screw to make angle adjustment vertically Loose this screw to make angle adjustment horizontally 18
ページ20に含まれる内容の要旨
2.3 Adjusting Lens Open camera’s base, a control key is attached at inner side of the base. Detach the control key and use this key for OSD or Lens setting. UP 2.3.1 Lens Setting Please turn the control key selection switch at the back panel to “Lens”.( ). Use the control key to do lens setting. UP Mini-Joystick The Cursors & the mini-joystick Turn the mini-joystick Up ( ) or Down ( ) to adjust zoom in / zoom ou
