ページ1に含まれる内容の要旨
POWER SPOT 700 II
User Manual
Revised 5/14/08 - visage
ページ2に含まれる内容の要旨
Power Spot 700 II™ ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 2
ページ3に含まれる内容の要旨
Power Spot 700 II™ Table of Contents 1. Introduction..............................................................................................................5 Unpacking .........................................................................................................5 Customer Support .............................................................................................5 Discharge Lamp Precautions ........................................................................
ページ4に含まれる内容の要旨
Power Spot 700 II™ 8.9.8 Adjustments and Calibrations (ADJU) .................................................31 8.9.9 Default Settings (DFSE) .......................................................................32 8.9.10 Feedback (FEED).................................................................................32 8.9.11 Fault Corrections (EFLD).....................................................................32 8.10 Error and Information Messages ...............................
ページ5に含まれる内容の要旨
Power Spot 700 II™ INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The Power Spot 700 II™, has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance.
ページ6に含まれる内容の要旨
Power Spot 700 II™ limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper and included in the shipping container. If the unit is under warra
ページ7に含まれる内容の要旨
Power Spot 700 II™ Never open this fixture while in use! During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fixture. This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp. This device falls under protection-class 1. Therefore it is essential that the device be grounded properly. All electrical connections must performed by qualified personal. Be sure
ページ8に含まれる内容の要旨
Power Spot 700 II™ 2. SAFETY INSTRUCTIONS The Power Spot 700 II™ is an extremely sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to follow the guidelines in this manual. The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never blocked. All
ページ9に含まれる内容の要旨
Power Spot 700 II™ 3. FEATURES • Pan 530° / Tilt 280° • 3 operation mode: DMX controlled, stand alone or sound activated • Electronic Power Supply • Control board with 4-digit display • Digital display can be turned 180° to fit different installation position • 2 Color Wheels: o Color Wheel: 16 User exchangeable colors • 3 Gobo Wheels: o Fixed: 9 plus open o Rotating: 14 User replaceable plus open • Auto test for all functions • Automatic Pan/Tilt Correction • Glass Dichroic Re
ページ10に含まれる内容の要旨
Power Spot 700 II™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, etc. Do not attempt operation or installation without a proper knowledge on how to so. This fixture was designed for indoor use only. Consistent operational breaks may ensure that the fixture will function properly for many years to come. Do not shake the fixture around. Avoid brute force when installing or operating the device. While ch
ページ11に含まれる内容の要旨
Power Spot 700 II™ Transportation and Handling The POWER SPOT 700 II™ comes with two carrying handles built into the base. Always transport the fixture by these handles. Never lift or carry the POWER SPOT 700 II™ by the yoke (head assembly) this can seriously damage the unit and will void your manufactures warranty. Connections Power supply: Electronic ballast with: 90~260 Volts, 50~60 Hz, Grounded contact type plug – Neutrik Powercon Connected load 1000W <=> 4.5 A (blind current c
ページ12に含まれる内容の要旨
Power Spot 700 II™ 5. FIXTURE LAYOUT 1. Moving Head 2. Carrying Handles 3. LED Menu Display 4. Head Tilt Lock 5. Omega Clamp 6. Ethernet Jack 7. 5-Pin DMX Out Connector 8. 5-Pin DMX In connector 9. Microphone Sensitivity 10. Build-In Microphone 11. Software-Update Connector 12. 3-Pin DMX Out Connector 13. 3-Pin DMX In Connector 14. Carrying Handle 15. Power On/Off 16. Lamp Fuse 17. Fan (air inlet/outlet) 18. Main Power Supply (Powercon) 19. Electronics Fu
ページ13に含まれる内容の要旨
Power Spot 700 II™ Side View - Menu and Display 20.4-Segment LED Menu Display 20 21 22 23 24 21. Mode Button 22. Enter Button 23. Up Button 24. Down Button 1. Head Assembly – The head assembly consist of the main output lens, and either the standard or CMY control module. 2. Carrying Handle – The fixtures includes two built-in carrying handles. Be sure to always handle the fixture by the built-in carrying handles. Never lift or carry the fixture by the
ページ14に含まれる内容の要旨
Power Spot 700 II™ 7. 5-PIN DMX Output Jack (CMY Version Only) – This 5-Pin XLR jack is used to send an outgoing DMX signal. For best results this jack should be terminated if it is the last fixture in a DMX daisy-chain (see termination on page 20). 8. 5-Pin DMX Input Jack (CMY Version Only) - This 5-Pin XLR jack is used to receive an incoming DMX signal. 9. Microphone Sensitivity Adjustment Knob – This knob is used to adjust the frequency sensitivity of the internal microphone when
ページ15に含まれる内容の要旨
Power Spot 700 II™ 17. Internal Cooling Fan – This fixture is equipped with two high-velocity variable speed fans mounted in the base to aid in the cooling process. These fans are designed to vary their velocity at different operating temperatures. When the fixture reaches a predetermined internal operating temperature the fans function at high speeds. The higher speeds provide better cooling associated with higher operating temperatures during long use. When the fixture is operating at a
ページ16に含まれる内容の要旨
Power Spot 700 II™ 6. MOUNTING AND INSTALLATION Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas were unauthorized personnel might reach the fixture. Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device’s weight. Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable. Mounting The POW
ページ17に含まれる内容の要旨
Power Spot 700 II™ Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE 0711-217 for proper installation in Europe To ensure proper installation, only qualified staff should attempt installation. Mounting points Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifica
ページ18に含まれる内容の要旨
Power Spot 700 II™ 90° b) Be sure to always use two cam locks mounted to the bottom of unit to ensure safe truss mounting (each two opposite threads max. M10x20). Secure the POWER SPOT 700 II™ Regardless of the rigging option you choose for your POWER SPOT 700 II™ always be sure to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a safety cable on the underside of the fixture, be sure to use this point and never secure a safety cable to
ページ19に含まれる内容の要旨
Power Spot 700 II™ 7. UNDERSTANDING DMX DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all the fixtures and the controller are DMX compliant. A DMX controller sends the DMX data instructions to
ページ20に含まれる内容の要旨
Power Spot 700 II™ chained and cannot be split, unless using an approved DMX splitter such as the Elation Opto Branch 4™ or DMX Branch/4™. Be sure to follow the above figure when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior. DMX-512 control
