ページ1に含まれる内容の要旨
®
About this Supplement
SpeedDome Ultra VIIE
This supplement provides detailed information
Day/Night Camera
about SpeedDome Ultra VIIE camera dome
features that are not currently covered in your
Dome Configuration
operator’s manual. This supplement supports
information found in the following manuals:
Utility
• Day/Night Camera Dome Configuration Utility
Operator’s Manual, 8200-0184-04
Operator’s Manual Supplement
NOTE: Keep this supplement with your operator’s
manual for reference
ページ2に含まれる内容の要旨
Table 1: DirectSet Menu Options DirectSet Menu Command Description The DirectSet Menu provides easy access to 0+DirectSet Toggle DirectSet Menu: Toggles commonly used SpeedDome Ultra VIIE features between displaying and hiding when used with compatible controllers. This allows the DirectSet menu. you to change or activate features without starting 1+DirectSet Dome Config Menu: Displays the the dome configuration menu. See Figure 1 for SpeedDome Ultra configuration examples of the
ページ3に含まれる内容の要旨
Command Description Menu Programming 16+DirectSet Stepped Scan: Initiates a clockwise rotation around the Navigation dome axis pausing briefly every The SpeedDome Ultra VIIE is programmed from 10° (at 1x zoom) for 3 seconds on-screen menus that are accessible through your using the current tilt, zoom and controller (keyboard, virtual keyboard, or Touch focus settings. ® Tracker ). 17+DirectSet Random Scan: Initiates a clockwise or counter-clockwise The starting point for progra
ページ4に含まれる内容の要旨
Figure 2. 5. Use the joystick to highlight Camera Functions and press the Focus Far button. The Camera Functions screen appears DOME CONFIGURATION MENU (Figure 5). PAN / TILT / ZOOM / SYNC OPTS CAMERA FUNCTIONS Figure 5. ALARMS / AREAS / PRESETS / PZ ON-SCREEN TEXT DISPLAY CAMERA FUN CAMERA FUNC CT TIIONS ONS LANGUAGE / PASSWORD DOME INFORMATION Auto White Bal Auto White Bal ON ON RESET TO FACTORY SETTINGS QUIT WITHOUT SAVING IR MODE IR MODE Auto Lo Auto Low w EXIT AND
ページ5に含まれる内容の要旨
You can create up to eight motion zones for every Figure 8. Preset scene. An example of a Preset scene with one motion zone is shown in Figure 6 CAMERA FUNCTIONS Auto White Bal ON Figure 6. IR MODE Auto Low MOTION DETECTION SETUP WDR OFF PRESET 1 AGC/Shutter Max Gain Limit ZONE 1 Open Shutter 28 dB 1/4 s RESET TO FACTORY SETTINGS EXIT One motion 3. Use the joystick to highlight the IR MODE field zone and press the Zoom In/Out button to change ESC/FOCUS = save
ページ6に含まれる内容の要旨
Figure 10. 6. Use the joystick to highlight the ZONE field. Use the Zoom In/Out button until the zone number (1-8) you want to apply to the Preset ALARMS/AREAS/HOME/PRESETS/PZ appears. SET ALARM ACTIONS 7. Use the joystick to highlight the SENS field. SET ALARM STATES Use the Zoom In/Out button until the SET HOME POSITION sensitivity level you want to apply to your zone SET NORTH POSITION appears. Note: Zone sensitivity ranges from AREA BOUNDARIES zero (no sensitivity) to five (h
ページ7に含まれる内容の要旨
13. Continue to select EXIT on every screen until Figure 14. menu programming ends. DOME CONFIGURATION MENU Note: Motion detection can be hidden without erasing the motion detection configuration (for PAN / TILT / ZOOM / SYNC OPTS example, during the day when motion is expected). CAMERA FUNCTIONS To hide motion detection, select Yes on the Hide ALARMS / AREAS / PRESETS / PZ All Zones field on the Motion Detection Setup ON-SCREEN TEXT DISPLAY screen. LANGUAGE / PASSWORD DOME INFOR
ページ8に含まれる内容の要旨
Figure 17. • Option 2 - Use the Set Home Position method to schedule one Sequence to run when the dome returns to its home position (after a SEQUENCE SETUP MENU defined period of inactivity). SEQUENCE NUMBER 1 Follow the steps below to run Sequences from the STEP 1-4 DWELL TIME Set Home Position screen: STEP PRESET MIN / SEC 1 1 0 0 1. Access the Dome Configuration Menu 2 1 0 0 (Figure 18) by pressing Iris Open, Focus Far 3 1 0 0 and Zoom Out on your controller. 4 1 0 0 EXIT
ページ9に含まれる内容の要旨
Figure 20. Setting Description Off Allows programming of three fixed speed SET HOME POSITION Patterns. The three Patterns are limited to a total of 99 pan/tilt/zoom movements (e.g., if one Pattern uses 50 movements, ACTION SEQUENCE 1 the remaining two Patterns are limited to a total of 49 movements). Note: The VM1 and VM96 systems only support the OFF setting. RETURN TIME MINS 10 3 Allows programming of three variable speed Patterns. Each Pattern can have EXIT up to
ページ10に含まれる内容の要旨
3. Use the joystick to highlight the PATTERN Select screen (Figure 23). Follow the steps below SELECT field and press Zoom In/Out to select to run a Pattern. Off, 3, or 16. 1. Enter the appropriate keyboard command to run Patterns 1, 2, or 3. The Pattern Select 4. Use the joystick to highlight EXIT and press screen appears. Focus Far to select. The Dome Configuration Menu appears. 2. Move the joystick to highlight the desired Pattern number (1-16) to run. 5. Use the joystick to highli
ページ11に含まれる内容の要旨
VM16E/ADTT16E (Black Touch AD2150/AD2350 1 Tracker) Supported Protocol RS-422 2 Maximum Presets 16 Supported Protocol SensorNet 3 1 Maximum Patterns 16 RS-422 DirectSet Menu Not supported Maximum Presets 96 – SensorNet Address Range 1-32 4 – RS-422 2 Maximum Patterns 16 Notes: 3 DirectSet Menu Yes (1) Requires the AD2083-02 series code converter. 3 (2) Preset information is stored at the converter, not the Address Range 1-16 or 1-64 dome. Notes: (3) Patterns are limited by tim
ページ12に含まれる内容の要旨
AD2050 MegaPower 1024 1 1 Supported Protocol RS-422 Supported Protocol RS-422 Manchester 2 2 3 Maximum Presets 16 Maximum Presets 16 or 60 64 3 4 Maximum Patterns 16 Maximum Patterns 16 16 DirectSet Menu Not supported DirectSet Menu Not Not 4 Address Range 1-1024 supported supported 5 5 Address Range 1-1024 1-1024 Notes: (1) Requires the AD2083-02 series code converter. Notes: (2) Preset information is stored at the converter, not the (1) Requires the AD2083-02 series code converte
ページ13に含まれる内容の要旨
Configuration Menu Specifications-Indoor Dome Languages ................English, French, German, Spanish, Italian, and Portuguese Operational Electrical Pan/Tilt: Manual Pan Speed .........................0.2°-100° per second Input Voltage.....................................18-30Vac, 50/60 Hz (scaled to zoom position) UL Class 2 LPS Manual Tilt Speed.........................0.25°-100° per second Design Tolerance..............................16-36Vac, 50/60 Hz (scaled to zoom po
ページ14に含まれる内容の要旨
Lens Design Mechanical Type ................................................................ Aspherical Height ...........................................................20.8cm (8in) Focal Length ............................................. 3.6 to 82.8mm Eyeball Diameter ..........................................12cm (4.7in) Aperture .................................................f1.6 (wide angle) f3.7 (telephoto) Weight: Viewing Angle (equivalent to 8-80 mm on 1/2" CCD Housing and
ページ15に含まれる内容の要旨
Other Declarations Declarations Thank you for using American Dynamics products. We support our products through an extensive and worldwide network of dealers. The dealer, through whom you originally Regulatory Compliance purchased this product, is your point of contact if you have a need for service or support. Our dealers are fully empowered Emissions ................................ 47 CFR, Part 15, Class A to provide the very best in customer service and support. ICES-003 Dealers
