ページ1に含まれる内容の要旨
Installation and User’s Guide
Omnidirectional Bar Code Scanner
IS6520/MS6520 Cubit™ Series
METROLOGIC INSTRUMENTS, INC.
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
L North America Headquarters Metrologic Instruments, Inc. Email: info@me trologic.com Website: www.metrologic.com Germany Metrologic Instruments GmbH 82178 Puchheim b. Email: info@europe.metrologic.com Munich, Germany South America Metrologic South America Rua Flórida 1821 - 5° Andar São Paulo, SP, Brasil Email: info@sa.metrologic.com Metrologic do Brasil Ltda Rua Flórida 1821 - 5° Andar São Paulo, SP, Brasil Email : info@br.metrologic.com Metrologic Asia (Pte) Ltd 31, Kaki Bukit Road 3 Email: i
ページ4に含まれる内容の要旨
iii March 2000 Printed in USA
ページ5に含まれる内容の要旨
T C Introduction ................................ ................................ ................................ ...... 1 ................................ ................................ ................. 2 Quick Start ................................ ................................ ................................ ...... 3 Installing the IS6520-41/MS6520-41 to the Host System ................................ .. 4 Installing the IS6520-47/MS6520-47 to the PC ................................
ページ6に含まれる内容の要旨
T C ................................ ................................ ....... ................................ ................................ . Warranty and Disclaimer ................................ ................................ ............ ................................ ................................ ................................ ....... ................................ ................................ ................................ ....... ................................ ....
ページ7に含まれる内容の要旨
* : Leave page blank Printer Note
ページ8に含まれる内容の要旨
I Metrologic's Cubit™ is a compact, omnidirectional bar code scanner that can be used as a presentation scanner or as the scanning component in Original Equipment Manufacturer (OEM) applications. Incorporating the latest in scanning technology Cubit™ can scan and decode all standard bar codes in any orientation. As an OEM product, the IS6520 is both easy to use and install. The IS6520 is equipped with three threaded mounting holes, serial programming and cables. The modular design of Cubit al
ページ9に含まれる内容の要旨
S A CCESSORIES The following is a list of the parts included in the IS6520/MS6520 Kit. • Cubit™ IS6520/MS6520 - Omnidirectional Scanning Engine • - AC to DC Power Transformer. mA output. One of the following may be included: • Cable with built in power jack (IS650-41/MS6520-41only) One of the following may be included: - MLPN 54xxx* - 2.1 m (7') straight cord, short strain relief Or - MLPN 53xxx* - 2.7 m (9') coiled cord, long strain relief * • – Powerlink cable with a 5-pin DIN female co
ページ10に含まれる内容の要旨
Q S 1. Connect the 10-pin RJ45 male connector into the jack on the Cubit™ IS6520/MS6520. You will hear a ‘click’ when the connection is made. 2. 3. Connect the power supply into an AC outlet. requirements of the power supply match the AC outlet. 4. When the IS6520 is ready to scan, the green LED will turn on, the red LED will flash and the scanner will beep once. 5. Place a bar code in front of the scanning window. The scanner will beep Cubit™ is shipped from the factory programmed
ページ11に含まれる内容の要旨
I IS6520-41/MS6520-41 H S 1. Turn off the host system. 2. Connect the 10-pin RJ45 male connector into the jack on the Cubit™ IS6520/MS6520. You will hear a ‘click’ when the connection is made. If the Cubit™ IS6520 is receiving power from the host system, skip to step #5. ( ) 3. 4. requirements of the power supply match the AC outlet. 5. PowerLink cable to the proper port on the host system. 6. Turn on the host system. Note: Plugging the scanner into a port on the host system does
ページ12に含まれる内容の要旨
I IS6520-47/MS6520-47 1. Turn off the PC. 2. Connect the 10-pin RJ45 male connector into the jack on the Cubit™ IS6520/MS6520. You will hear a ‘click’ when the connection is made. 3. 4. match the AC outlet. 5. Disconnect the keyboard from the PC. 6. The PowerLink cable is terminated with a 5-pin DIN female connector on one end, and a 6-pin mini DIN male on the other. Metrologic will supply an adapter cable with a 5-pin DIN male connector on one end and a 6-pin mini According to the termi
ページ13に含まれる内容の要旨
To maintain compliance with standard CSA C22.2 No. 950/UL 1950 and norm EN 60950, the power source should meet applicable performance requirements for a limited power source. 6
ページ14に含まれる内容の要旨
D P OWER L C S from the scanner, Metrologic recommends that the from the & 1. Locate the small ‘pin-hole’ on the back of the scanner. 2. 3. Insert the paperclip (or other small metallic pin) into the small ‘pin-hole’. 4. You will here a faint ‘click’. Pull gently on the strain-relief of the cable and it will slide out of the scanner. 7 PowerLink Bend an ordinary paperclip into the shape shown above. PowerLink cable. host system is off and the power supply has been disconnected power
ページ15に含まれる内容の要旨
S P C B A D Serves as an audible indicator. B. Green & Red During normal operation, the green LED is on. This indicates that the laser is on and the unit is ready to scan. On a successful read of a bar code, the red LED will turn on. After communication to the host is complete, the red LED will turn off. LEDs are also used as diagnostic indicators and mode indicators. C. Laser light emits form this aperture. D. The IS6520/MS6520 scanner has a 10-pin modular jack. The 10-pin modular plug
ページ16に含まれる内容の要旨
M H OLES located on the back of the scanner. The following diagram shows the exact location of each mounting hole. The mounting holes are 6 millimeters deep and are threaded for use with 3 millimeter screws. Using a screw that is longer than 6 millimeters can potentially damage the scanner. 9 62 mm (2.4") 41 mm (1.6") 20 mm (0.8") 0 mm (0") (3.2") (0.8") (0") 82 mm 20 mm 0 mm Caution: Each IS6520/MS6520 Cubit™ is equipped with three threaded mounting holes OUNTING
ページ17に含まれる内容の要旨
A I When the IS6520/MS6520 scanner is in . Eight settings are available for (normal, 6 alternate tones ® Programming Guide MLPN 2407. When the will turn on, then the red LED will flash and the scanner will beep once. (The red LED will remain on for the duration of When the scanner will flash and the scanner beeps once (if programmed green light does not flash, then the bar code has not successfully read. This tone is a failure indicator . Refer to “Failure Three Beeps - During Operation
ページ18に含まれる内容の要旨
F M ODES Flashing Green and One subsystem failure. Return the unit for repair at an failure. with Both Off If, upon power up, the scanner emits a continuous s - On Power Up volatile memory that holds the scanner configuration has failed. Return the unit for repair at an authorized service 11 center. If the scanner beeps 3 times on power up then, the non- Three Beep Return the unit for repair at an authorized service center. razzberry tone, then the scanner has an electronic failure. LEDs R
ページ19に含まれる内容の要旨
V I IS6520/MS6520. When the scanner is on, the flashing or stationary, activity of the LEDs indicates the status of the LEDs will not be illuminated if the scanner is not receiving power from the host or transformer. is illuminated. The green LED will remain illuminated until the laser is deactivated. During the power save mode, the laser will turn on and turn off. During this period, the green LED remains illuminated. will flash and the scanner will beep once. If the red LED After a succe
ページ20に含まれる内容の要旨
P M ODES The IS6520/MS6520 Cubit™ has 3 modes of programming. Cubit™ can be configured by scanning the bar codes located in ® Configuration Guide (MLPN 2407). Please refer to this guide for instructions. This manual can be downloaded for FREE from Metrologic’s website (www.metrologic.com). MetroSet™: This user-friendly Windows-based configuration program allows you to simply ‘point-and-click’ at the desired scanner options. This program can be downloaded for FREE from Metrologic’ website
