ページ1に含まれる内容の要旨
®
PowerScan PBT7100
Base Station
Quick Reference Guide
ページ2に含まれる内容の要旨
Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affili- ates ("Datalogic" or “Datalogic Scanning”). Owners of Datalogic products are hereby granted a non-exclusive,
ページ3に含まれる内容の要旨
Table of Contents Statement of Agency Compliance ........................................................... 3 FCC Class B Compliance Statement .................................................. 3 Canadian Notice ............................................................................ 3 Solids and Water Protection ............................................................ 3 Power Supply ................................................................................ 3 Laser Cautions ......
ページ4に含まれる内容の要旨
NOTES 2 PowerScan® PBT7100 Base Station
ページ5に含まれる内容の要旨
Statement of Agency Compliance Statement of Agency Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two con- ditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Class B Compliance Statement The user is cautioned that changes or modifications not expressly approved by the part responsible for compliance could void
ページ6に含まれる内容の要旨
Laser Cautions The imager may contain a laser pointer (this is a value-added option), which is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J for Class II and IEC 60825-1 for Class 2 products. Class II (2) products are not considered to be hazardous. Laser pointer models of the imager contain a Visible Laser Diode (VLD) at a wavelength of 635-670 nanometers and is designed so that there can be no human access to harmful levels of laser light dur- ing no
ページ7に含まれる内容の要旨
Software Product Policy 2.2 End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwise reproduce or reman- ufacture the Software, whether modified or unmodified, nor sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the Software to any other person or organization, for purposes other than as expressly provided in this Agreement, without Datalogic’s prior written consent. 3. Transfers, Support. 3.1 Any copying, installing, reproduction, rem
ページ8に含まれる内容の要旨
TEMPORANEOUS, OR FUTURE AGREEMENTS OR DEALINGS BETWEEN THE PARTIES, WHETHER ORAL OR WRITTEN, EXCEPT AS SET FORTH IN A FUTURE WRITING SIGNED BY BOTH PARTIES. 8. Limitation Of Liability. EXCEPT AS PROVIDED IN SECTION 7, DATALOGIC SHALL NOT BE LIABLE FOR ANY CLAIMS AGAINST END USER BY ANY OTHER PARTY. IN NO EVENT SHALL DATALOGIC'S LIABILITY FOR DAMAGES, IF ANY, WHETHER BASED UPON CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, STRICT LIA- BILITY, WARRANTY, OR ANY OTHER BASIS, EXCEED THE
ページ9に含まれる内容の要旨
Getting Started Connection Figure 1 shows how to connect the Base Station to a terminal, PC or other host device. Turn off the host before connection and consult the manual for that equipment (if necessary) before proceeding. Base Station Connection and Routing — Fully insert the Power Cable and Interface (I/F) Cable connectors into their respective ports in the under- side of the Base Station (see Figure 1). Alternatively, you can either loop the cables around the routing clips and back th
ページ10に含まれる内容の要旨
K e W y e b d o a g r d e Host Connection — Typically, the interface type was specified at the time your reader and/or Base Station was ordered, however you should verify before connection that the Base Station’s cable type is compatible with your host equipment. Most connections plug directly into the host device as shown in Figure 2. Keyboard Wedge interface cables have a ‘Y’ connection where its female end mates with the male end of the cable from the keyboard and the remaining end at
ページ11に含まれる内容の要旨
Getting Started Figure 3. Labeling and Nomenclature This illustration shows label placement ONLY. Antenna For actual regulatory, patent and other applicable Link Bar Code information, view the labels on the product intself, or call your nearest sales or service office. Link Button Amber LED Green LED Scanner Regulatory Latch Label (on underside) ® PowerScan PBT7100 readers and Base Stations can be configured to be compatible with Power- ® Scan 7000BT imagers and Base Stations. Consult the P
ページ12に含まれる内容の要旨
Select the desired interface by scanning the associated barcode below. INTERFACE SELECTION BARCODE RS-232 Standard RS-232 Wincor-Nixdorf RS-232 for OPOS/UPOS/ JavaPOS Wand Emulation IBM 46XX Port 5B IBM 46XX Port 9B USB HID POS a USB Com USB Keyboard USB Alternate Keyboard USB OEM a. Download the correct USB Com driver from www.datalogic.com ® 10 PowerScan PBT7100 Base Station
ページ13に含まれる内容の要旨
Getting Started Interface selection — continued INTERFACE SELECTION BARCODE Keyboard AT Keyboard Wedge for PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Standard Key Encoding Keyboard AT-NK Keyboard Wedge for IBM AT PS2 with standard key encoding but without external keyboard Keyboard AT-ALT Keyboard Wedge for AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Alternate Key Keyboard AT-ALT-NK Keyboard Wedge for IBM AT PS2 with alternate key encoding but without external keyboard Keybo
ページ14に含まれる内容の要旨
Interface selection — continued Keyboard IBM-MB Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make break keyboard Keyboard DIG-VT Keyboard Wedge for DIGITAL Terminals VT2xx, VT3xx, VT4xx Keyboard USB-KBD- Apple USB Keyboard for Apple computers ® 12 PowerScan PBT7100 Base Station
ページ15に含まれる内容の要旨
EUROPEAN DECLARATION OF CONFORMITY Datalogic Scanning, Inc. hereby declares that the apparatus specified below has been tested and found compliant to the following European Council Directives and Harmonized Standards: Apparatus: PowerScan PBT7100 System Directives: EMC 2004/108/EC Low Voltage 2006/95/EC R&TTE 1999/5/EC RoHS 2002/95/EC WEEE 2002/96/EC Standards: EN 301 489-1 v 1.6.1 reference EN 301 489-17 v 1.2.1:2002 Radio Immunity EN 300 328 v 1.7.1: 2006 Radio Emissions EN 50392:2004 Human
ページ16に含まれる内容の要旨
Australia Japan Datalogic Scanning Pty Ltd Datalogic Scanning KK Telephone: [61] (2) 9870 3200 Telephone: 81 (0)3 3491 6761 australia.scanning@datalogic.com japan.scanning@datalogic.com France and Benelux Latin America Datalogic Scanning Sarl Datalogic Scanning, Inc Telephone: [33].01.64.86.71.00 Telephone: (305) 591-3222 france.scanning@datalogic.com latinamerica.scanning@datalogic.com Germany Singapore Datalogic Scanning GmbH Datalogic Scanning Singapore PTE LTD Telephone: 49 (0) 61 51/93 58-0
