ページ1に含まれる内容の要旨
model g0636Xb
ultimate 17" bandsaW
w/motor braKe
manual insert
t he Model g 0636XB is the same as the Model g 0636X, except it has a magnetic brake motor and a square
fence rail. Besides the instructions, data sheet, circuit requirements, parts, and wiring diagram in this insert,
the content in the Model g 0636X owner's manual is the same for both machines. Before operating your
new machine, you Must read and understand this insert and the entire Model g 0636X manual to reduce
the risk of in
ページ2に含まれる内容の要旨
4. tighten the hex nut on the fence handle test run against the fence pivot block (figure 2). 1. Follow steps 1-3 in the g0636X Manual on page 20. pivot Block 2. Verify that the machine is operating correctly by turning the switch disabling key (figure 4) to "1" and turning the machine ON. Fence handle —When operating correctly, the machine runs smoothly with little or no vibration or rubbing noises. hex nut — investigate and correct strange or unusual figure 2. Fence handle component
ページ3に含まれる内容の要旨
T S I aligning fence t o ensure cutting accuracy when the fence is first installed, the fence should be aligned with the miter slot. to align the fence parallel with the miter slot: OFF Button 1. disConneCt BandsaW FroM poWer! figure 5. resetting the switch. 2. Make sure the miter slot is aligned with the bandsaw blade (see g0636X Manual page 6. turn the switch disabling key to "0", as shown 25, Aligning Table). in figure 4. 7. try to turn the machine ON. 3. Mount the fence next to the mi
ページ4に含まれる内容の要旨
pointer calibration magnetic brake adjustment your new bandsaw is equipped with a fence mea- t he space between the magnetic brake and brake surement system that includes a fence pointer, shoe is preset by the factory at 0.2mm (0.008"). which must be calibrated when the bandsaw is h owever, you should adjust this space every two first set up. to three years, or when it takes over five seconds for the brake to stop the motor. to calibrate the pointer: t ools needed 1. if the fence is mounted
ページ5に含まれる内容の要旨
MACHINE DATA SHEET MODEL G0636XB 17" ULTIMATE BANDSAW w/MOTOR BRAKE Product Dimensions: Shipping Dimensions: Electrical: Motor: Main Specifications: Operation Information Cutting Capacities Blade Information Model G0636XB Page 1 of 2 Mod
ページ6に含まれる内容の要旨
Table Information Fence Information Dust Collection Construction Materials Other Specifications: Features: Model G0636XB Page 2 of 2 -6- Model g 0636XB
ページ7に含まれる内容の要旨
section 2: circuit re Quirements power connection device 220v single-phase t he type of plug required to connect your machine to power depends on the type of service you cur- rently have or plan to install. We recommend using the plug shown in f igure 11. serious personal injury could occur if you connect the machine to power before com- pleting the setup process. do not connect the machine to the power until instructed later in this manual. electrocution or fire could result if machine is
ページ8に含まれる内容の要旨
g 0636Xb electrical c omponents figure 13. junction box wiring. figure 12. Magnetic switch. figure 14. Capacitors. -8- Model g 0636XB
ページ9に含まれる内容の要旨
g 0636Xb Wiring diagram 5hp 220 v, 1-ph View this page in color at www.grizzly.com. X G 220 VAC Y L6-30 PLUG (as recommended) see figure 12 see figures 13 & 14 The motor wiring shown here is current at the time of printing, but it may not match your machine. Always use the wiring diagram inside the motor junction box. Model g 0636XB -9-
ページ10に含まれる内容の要旨
main breakdown -10- Model g 0636XB
ページ11に含まれる内容の要旨
main parts l ist REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P0636X001 HANDLE 49 P0636X049 STOP SWITCH 2 P0636X002 LEVER ROD M16-2 50 P0636X050 KEY SWITCH 3 PN13M HEX NUT M16-2 51 P0636X051 SWITCH PLATE 4 P0636X004 ROTATE SHAFT 52 P0636X052 CONNECTING CORD 5 PSBS25M BUTTON HD CAP SCR M10-1.5 X 20 53 P0636X053 CONNECTING CORD 6 PLW06M LOCK WASHER 10MM 54 PLW03M LOCK WASHER 6MM 7 P0636X007 BLD TRACKING KNOB M10-1.5 x 25 55 P0636X055 ADJUST BOLT 8 P0636X008 BLD TRACKING LOCK LEVER 10MM 56 PB16
ページ12に含まれる内容の要旨
main parts l ist c ontinued REF PART # DESCRIPTION REF PART # DESCRIPTION 101 PS52M PHLP HD SCR M4-.7 X 20 108 P0636X108 PLATE 102 P0636X102 TERMINAL BLOCK 109 P0636X109 SWITCH CORD 103 P0531B080 MAGNETIC SWITCH MPE-18 22A 110 PW05M FLAT WASHER 4MM 103-1 P0531B080 MAG SWITCH BACK COVER 111 P0636X111 DOOR LATCH SWITCH ADZ-S11 103-2 P0531B080-1 CONTACTOR SDE MA-18 220V 111-1 P0636X111-1 DOOR LATCH 103-3 P0531B080-2 RELAY SDE RA-30 (18-26) 112 PFS10M FLANGE SCREW M4-.7 X 35 103-4 P0531B080-3 MAG
ページ13に含まれる内容の要旨
t able-f ence-t runnion breakdown Model g 0636XB -13-
ページ14に含まれる内容の要旨
t able-f ence-t runnion parts l ist REF PART # DESCRIPTION REF PART # DESCRIPTION 19 PSB31M CAP SCREW M8-1.25 X 25 150-5 PFS17M FLANGE SCREW M4-.7 X 8 37 PLW04M LOCK WASHER 8MM 150-6 P0513X2B157-6 PIVOT BLOCK 77 PW03M FLAT WASHER 6MM 150-7 PN03M HEX NUT M8-1.25 78 PFS11M FLANGE SCREW M6-1 X 10 150-8 P0513X2B157-8 HANDLE 104 PW01M FLAT WASHER 8MM 150-9 P0513X2B157-9 SHAFT 105 PLW04M LOCK WASHER 8MM 150-10 P0513X2B157-10 SPECIAL PLASTIC SET SCREW 106 PB09M HEX BOLT M8-1.25 X 20 150-11 P0513X2B157-
ページ15に含まれる内容の要旨
REF PART # DESCRIPTION REF PART # DESCRIPTION 167-12 P0566192 COVER 169-8 PR03M EXT RETAINING RING 12MM 167-13 P0636XB167-13 FIXED BOLT 169-9 P6201 BALL BEARING 6201ZZ 167-14 P0566191 EXTENSION RACK 169-10 P0636X249 UPPER SPACING SLEEVE 167-15 PFH19M FLAT HD SCR M4-.7 X 10 169-11 P0636X250 SHAFT 167-16 P0566207 RACK 169-12 P0636X184 UPPER GUIDE SUPPORT BLOCK 167-17 P0566206 UPPER GUIDE BAR 169-13 PB04M HEX BOLT M6-1 X 10 167-20 P0566194 PINION GEAR 170 PSBS04M BUTTON HD CAP SCR M8-1.25 X 35 167
ページ16に含まれる内容の要旨
l abels breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION 300 P0636XB300 MODEL NUMBER LABEL 310 P0636X310 BLADE ASSEMBLY DIRECTION LABEL 301 P0636XB301 MACHINE ID LABEL 311 G8589 GRIZZLY NAMEPLATE-LARGE 302 PLABEL-11 SAFETY GLASSES LABEL 312 P0636X312 TENSION ADJ LABEL 303 PLABEL-12 READ MANUAL LABEL 313 P0636X313 TABLE ANGLE SCALE 304 PLABEL-14 ELECTRICITY LABEL 314 P0636X314 TABLE LOCK LEVER LABEL 305 PPAINT-1 GRIZZLY GREEN PAIN
