ページ1に含まれる内容の要旨
OPERATION AND PARTS MANUAL
CUTTER 1
MODEL CD613H18
(HONDA GX390 GASOLINE ENGINE)
MODEL CD605E16
(5 HP ELECTRIC MOTOR)
CONCRETE/ASPHALT SAW
Revision #6 (06/06/08)
To find the latest revision of this
publication, visit our website at:
www.stowmfg.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
P/N 25498
ページ2に含まれる内容の要旨
STOW CUTTER 1 SAW — PROPOSITION 65 WARNING Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are: Leadfromlead-basedpaints. Crystallinesilicafrombricks. Cementandothermasonryproducts. Arsenicandchromiumfromchemically treatedlumber. Your risk from these exposures
ページ3に含まれる内容の要旨
NOTES STOW CUTTER 1 SAW — OPERATION & PARTS MANUAL — REV. #6 (06/06/08) — PAGE 3
ページ4に含まれる内容の要旨
STOW CUTTER 1 SAW — TABLE OF CONTENTS Proposition 65 Warning ............................................. 2 HONDA GX390K1QWT2/ Table Of Contents ..................................................... 4 GX390U1QWT2 ENGINES Parts Ordering Procedures ....................................... 5 Air Cleaner Assembly.........................................42-43 Safety Message Alert Symbols .............................. 6-7 Camshaft Assembly ...........................................44-45 Rules For Sa
ページ5に含まれる内容の要旨
STOW CUTTER 1 SAW — PARTS ORDERING PROCEDURES When ordering parts, please supply the following information: ❒ ❒❒❒ ❒ Dealer account number ❒ ❒❒❒ ❒ Dealer name and address ❒ ❒❒❒ ❒ Shipping address (if different than billing address) ❒ ❒❒❒ ❒ Return fax number ❒ ❒❒❒ ❒ Applicable model number ❒❒ ❒❒❒ Quantity, part number and description of each part ❒❒❒ Specify preferred method of shipment: ❒❒ ✓ FedEx or UPS Ground Note: Unless otherwise indicated by customer, all ✓ FedEx or UPS Second Day or Third D
ページ6に含まれる内容の要旨
STOW CUTTER 1 SAW — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! HAZARD SYMBOLS Safety precautions should be followed at all times when operating Lethal Exhaust Gases this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to Engine exhaust gases contain poisonous yourself and others. carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled. NEVER operate this equipment in a conf
ページ7に含まれる内容の要旨
STOW CUTTER 1 SAW — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting Respiratory Hazard ALWAYS place the engine ON/OFF switch in the OFF position, when the saw ALWAYS wear approved respiratory protection. is not in use. Over Speed Conditions Sight and Hearing hazard NEVER tamper with the factory settings of the engine governor or settings. Personal injury ALWAYS wear approved eye and hearing and damage to the engine or equipment can protection. result if operating in speed ranges above maximum
ページ8に含まれる内容の要旨
STOW CUTTER 1 SAW — RULES FOR SAFE OPERATION RULES FOR SAFE OPERATION ■ NEVER touch the hot exhaust manifold, muffler or cylinder. Allow CAUTION: these parts to cool before servicing Failure to follow instructions in this manual may the saw. lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when ■ High Temperatures – Allow the engine to c
ページ9に含まれる内容の要旨
STOW CUTTER 1 SAW — RULES FOR SAFE OPERATION General Safety ■ MAKE CERTAIN the power cord/extension cord is free from damage and that the grounding circuit is operational. ■ ALWAYS read, understand, and follow procedures in Operator's Manual before attempting to operate equipment. ■ MAKE CERTAIN the extension cord that you are using is intended to be used in the environment you are using it in. If ■ ALWAYS be sure the operator is familiar with proper safety an extension is used, NEVER submerg
ページ10に含まれる内容の要旨
STOW CUTTER 1 SAW — RULES FOR SAFE OPERATION Saw Transportation Safety Machine Operation And Safety Decals ■ Use appropriate lifting equipment to ensure the safe The STOW CUTTER 1 SAW is equipped with a number of movement of the saw. operation and safety decals. Should any of these decals become unreadable, replacements can be obtained from your dealer. ■ DO NOT use the handle bars and/or front pointer as lifting points. ■ When trasporting of the saw is required, place saw directly inside towi
ページ11に含まれる内容の要旨
STOW CUTTER 1 SAW — SPECIFICATIONS (SAW) C G B A F Side View E D Front View Figure 2. STOW CUTTER 1 SAW Dimensions Table 1. Cutter 1 Specifications REFERENCE LETTER DESCRIPTION DIMENSION (cm) Max Height 37.0 In. (94 cm) A Max Length (Front Pointer Raised) 32.0 In. (80 cm) B Max Length (Front Pointer Lowered) 54.5 In. (138 cm) C Max Width 21.5 In. (55 cm) D Rear Wheel Base 17.0 In. (40 cm) E Front Wheel Base 10.0 In. (25.4 cm) F G Handle Bar Width 21.5 In. (55 cm) DESCRIPTION WEIGHT (KG) ENGINE
ページ12に含まれる内容の要旨
STOW CUTTER 1 SAW — SPECIFICATIONS (ENGINE) Table 2. Specifications (Engine) HONDA Model GX390K1QWT2/GX390U1QWT2 Air-cooled 4 stroke, Single Type Cylinder, OHV, Gasoline Engine 3.5 in. X 2.5 in. Bore X Stroke (88 mm x 64 mm) D) isplacement 23.7 cu-in. (389 cc M. ax Output 13.0 H.P./3600 R.P.M Engine Approx. 1.72 U.S. Gallons Fuel Tank Capacity (6.5 Liters) Unleaded Automobile Gasoline Fuel 86 Octane or higher L) ube Oil Capacity 1.16 US qt (1.1 liter Speed Control Centrifugal Fly-weight Type Met
ページ13に含まれる内容の要旨
STOW CUTTER 1 SAW — CONTROLS & COMPONENTS CONTROLS & COMPONENTS 8. Cutting Blade – Use appropriate type blades for cutting Figure 3 shows the location of the basic controls or components concrete or asphalt. for the STOW CUTTER 1 SAW. Listed below is a brief 9. Blade Guard – Covers saw blade and flips up to allow explanation of each control or component. (Gasoline-powered blade to be changed. unit shown) 10. Belt Tension Adjuster – Adjusts belt tension. 11. Front Pointer – Front pointer wheel
ページ14に含まれる内容の要旨
STOW CUTTER 1 SAW — BASIC ENGINE BASIC ENGINE Figure 4. Engine Controls and Components 6. Choke Lever – Used in the starting of a cold engine, or in Initial Servicing cold weather conditions. The choke enriches the fuel The engine (Figure 4) must be checked for proper lubrication and mixture. filled with fuel prior to operation. Refer to the manufacturers engine 7. Air Cleaner – Prevents dirt and other debris from entering manual for instructions & details of operation and servicing. the fuel
ページ15に含まれる内容の要旨
STOW CUTTER 1 SAW — PREPARATION/PRE-INSPECTION PREPARATION / PRE-INSPECTION WARNING 1. Read and fully understand this manual, the safety instructions in particular, and ALWAYS use a grounded (3-wire) extension cord and MAKE the engine manufacturer's manual CERTAIN that the motor is connected to a properly grounded supplied with the saw. electric circuit to protect the operator from possible electric shock. 2. Select the correct blade for each application. If abrasive NEVER! touch the power co
ページ16に含まれる内容の要旨
STOW CUTTER 1 SAW — PREPARATION/PRE-INSPECTION 3. Insert and remove the dipstick without screwing it into the filler Guards And Covers neck. Check the oil level shown on the dipstick. WARNING 4. If the oil level is low (Figure 7), fill to the edge of the oil filler hole with the recommended oil type (Table 4). NEVER operate the saw without blade guards and covers in place. DO NOT operate with the front of the blade guard raised. The blade exposure cannot exceed 180 degrees during operation.
ページ17に含まれる内容の要旨
STOW CUTTER 1 SAW — PREPARATION/PRE-INSPECTION V-belt Alignment and Tensioning This saw is equipped with a premium V-belt that has been aligned and tensioned by factory personnel. The V-belt must be aligned and tensioned for proper operation of the saw. Use the following procedure to check the alignment of V-belt: 1. Remove the bolts that secure the V-belt cover (Figure 9) to the saw frame. Figure 10. Pulley Alignment 3. Check V-belt tension by using a tension meter (3.0 lbs.) against the ins
ページ18に含まれる内容の要旨
STOW CUTTER 1 SAW — BLADES BLADES 2. Edge of the Steel Core - Check the diameter edge for discoloration (blue oxidation) indicating an overheating Saw blades, or cutting disks, are available in either an abrasive condition caused by insufficient cooling water/air. design or as diamond blades. Either blade will work on the Overheating of blades may lead to loss of core tension and/ STOW CUTTER 1 SAW , however, diamond blades are or increase the possibility for blade failure. Make sure the reco
ページ19に含まれる内容の要旨
STOW CUTTER 1 SAW — BLADE PLACEMENT BLADE PLACEMENT WARNING WARNING Dropping or forcing the blade onto the cutting Failure to thoroughly inspect the diamond surface can severely blade for operational safety could result in damage the diamond blade and may damage to the blades or the saw and may cause serious damage to the saw and cause injury to the user or others in the bodily harm. operating area. Blade Removal and Replacement 1. Blade Guard - Pivot the blade guard front cover all the way ba
ページ20に含まれる内容の要旨
STOW CUTTER 1 SAW — INITIAL START-UP INITIAL START-UP 3. Place the Engine ON/OFF switch (Figure 13) in the "ON" position. CAUTION CAUTION CAUTION CAUTION CAUTION DO NOT attempt to operate the saw until the Safety, General Information and Inspection sections of this manual have been read and thoroughly understood. Depending on engine manufacturer, operating steps may vary. See engine manufactures operating manual. CAUTION CAUTION CAUTION CAUTION CAUTION Figure 13. Engine ON/OFF Switch NEVER o
