ページ1に含まれる内容の要旨
INSTRUCTION MANUAL
18" Band Saw
(Model 28-682)
PART NO. 911988 - 07-28-04
Copyright © 2004 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call 1-800-223-7278 (In Canada call 1-800-463-3582).
ページ2に含まれる内容の要旨
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ADDITIONAL S
ページ3に含まれる内容の要旨
SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situ
ページ4に含まれる内容の要旨
GENERAL SAFETY RULES READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock, fire, and/or serious personal injury or property damage. IMPORTANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY, READ THE INSTRUCTION an attachment to do a job for which it was not MANUAL BEFORE OPERATING THE MACHINE. designed. Damage to the machine and/or injury may Learning the machine’s application, limitatio
ページ5に含まれる内容の要旨
ADDITIONAL SAFETY RULES FOR BAND SAWS FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY. 1. DONOTOPERATE THIS MACHINE UNTIL it is 14. NEVER REACH UNDER THE TABLE while the assembled and installed according to the machine is running. instructions. 15. TURN THE MACHINE “OFF” to back out of an 2. OBTAIN ADVICE from your supervisor, uncompleted or jammed cut. instructor, or another qualified person if you are 16. MAKE “RELIEF” CUTS prior to cutting long curves. not familiar with th
ページ6に含まれる内容の要旨
POWER CONNECTIONS A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of the same ch
ページ7に含まれる内容の要旨
3. Grounded, cord-connected machines intended for GROUNDED OUTLET BOX use on a supply circuit having a nominal rating between 150 - 250 volts, inclusive: CURRENT CARRYING PRONGS If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. C, the machine will have a grounding plug that looks like the plug illustrated in Fig. C. Make sure the machine is connected to an outlet having the same configuration as the plug. No adapter is available or sho
ページ8に含まれる内容の要旨
FUNCTIONAL DESCRIPTION FOREWORD Delta Model 28-682 is an 18" Wood Cutting Band Saw. This machine has speeds of 2300 and 3250 SFPM (surface feet 1 per minute). Its blade to frame capacity is 17 /2" and its height under guide capacity is 12". The band saw has a quick 3 blade tensioning mechanism for ease of changing blades. The Delta Model 28-682 has a large 17 /4"x18" cast iron table that can be tilted 48 degrees to the right and 10 degrees to the left. The band saw also comes with a 4" O.D. dust
ページ9に含まれる内容の要旨
UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed B with a soft cloth moistened with kerosene. (Do not use acetone, gasoline or lacquer thinner for this purpose.) After cleaning, cover the unpainted surfaces with a good quality A household floor paste wax. 1. Remove the four bolts (A) Fig. 1 (three of which are shown) that attach the saw (B) to the shippin
ページ10に含まれる内容の要旨
TABLE 1. Remove the table pin (A) Fig. 5. 2. Align the blade with the table slot (B) Fig. 5. Slide the table until the blade has reached the center cutout (C) Fig. 5, then rotate the table 90 degrees toward the front of the machine. NOTE: Make sure that the table slot (B) Fig. 6 is facing toward the right of the machine. 3. Align the two table studs (A) Fig. 6, in the bottom of the table, with the two holes in the trunnion assemblies. 4. Thread the trunnion lock knob (D) Fig. 7 onto the table
ページ11に含まれる内容の要旨
FENCE 1. Align the two holes (A) Fig. 9 in the front fence rail with the two holes (B) in the front of the table. NOTE: Make sure that the scale on the front fence rail is facing upward. 2. Insert a 1/4-20 x 1-1/2" socket-head cap screw through one of the holes (A) Fig. 9 hole in the front fence rail. Place a spacer on the screw between the front fence rail and the table. Thread the screw into the front of the table. Repeat for the other hole (A) in the front fence rail. Tighten the two screws s
ページ12に含まれる内容の要旨
OPERATION OPERATIONAL CONTROLS AND ADJUSTMENTS STARTING AND STOPPING SAW The power switch is located on the left side of the machine. To turn the machine “ON”, push the green start button (A) Fig. 14. To turn the machine “OFF”, push the red stop button (B). LOCKING SWITCH IN THE “OFF” POSITION IMPORTANT: When the tool is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use, using a padlock (C) Fig. 15 with a 3/16" diameter shackle. A C B Fig. 14 Fig. 15 TILTI
ページ13に含まれる内容の要旨
4. Raise the blade tension lever to the “up” position and turn it clockwise to increase tension or counter- clockwise to relieve the tension. 5. After the first turn, lower the blade tension lever and check the tension scale. If the tension is still not correct, repeat the procedure. The tension scale is correct for standard blades used on average work. Although you may rely on the feel or tone of the blade, Delta recommends that you use the tension scale to avoid blade breakage by applying too
ページ14に含まれる内容の要旨
CHANGING SPEEDS DISCONNECT MACHINE FROM POWER SOURCE. 1. Open the bottom access door (See D, Fig. 26). E 2. Locate and loosen motor release handle (C) Fig. 20A inset by turning it counter-clockwise. 3. Lift up motor assembly and move belt (A) to desired groove on motor pulley (B). Move belt to outer groove C (D) for 2300 SFPM, or to inner groove (E)for 3250 SFPM. 4. Push down on motor assembly and then turn motor release handle (C) clockwise to tighten belt. D 5. Close the bottom access door. A
ページ15に含まれる内容の要旨
ADJUSTING THE TABLE POSITIVE STOP A DISCONNECT MACHINE FROM POWER SOURCE. This machine is equipped with a positive stop that allows the table to be rapidly positioned at 90 degrees to the blade after the table has been tilted. To check and adjust: 1. Place the table in the 90 degree position and lock it in place. Fig. 24 2. Place a square (A) Fig. 24 on the table with one end against the blade to check for 90 degrees. 3. If an adjustment is necessary, loosen the locknut (B) C Fig. 25 and tighten
ページ16に含まれる内容の要旨
A A Fig. 28 Fig. 28A ADJUSTING RESAW GAUGE The resaw gauge (A) attaches to the fence (Fig. 28). Slide it along the fence slot until the edge is slightly in front of the blade teeth. Use this gauge for resawing operations and for cutting warped workpieces. ADJUSTING BELT TENSION If it becomes necessary to adjust the belt tension on the machine, turn the motor release handle (A) Fig. 28A counter- clockwise. Lower or raise the motor, and when adjustment is complete, tighten the motor release handle
ページ17に含まれる内容の要旨
BAND SAW BLADES A band saw blade is a delicate piece of steel that is subjected to tremendous strain. You can obtain long use from a band saw blade if you use it properly. Be sure you use blades of the proper thickness, width and temper for the various types of material and cuts. Always use the widest blade possible. Use narrow blades only for sawing small, abrupt curves and for fine, delicate work. This will save blades and will produce better cuts. For cutting wood and similar materials, Delta
ページ18に含まれる内容の要旨
Trouble: BAND SAW VIBRATES EXCESSIVELY. Probable Cause Remedy 1. Machine not mounted securely to stand. 1. Tighten all mounting hardware. 2. Stand on uneven surface. 2. Reposition on flat level surface. 3. Worn belt. 3. Replace belt. 4. Pulley not aligned. 4. Adjust pulleys. 5. Motor not fastened securely. 5. Tighten all mounting hardware. Trouble: BAND SAW DOES NOT COME UP TO SPEED. Probable Cause Remedy 1. Low voltage due to improper extension cord size. 1. Replace with adequate size cord. 2.
ページ19に含まれる内容の要旨
MAINTENANCE KEEP MACHINE CLEAN LUBRICATION Periodically blow out all air passages with dry compressed Apply household floor paste wax to the machine table and air. All plastic parts should be cleaned with a soft damp extension table or other work surface weekly. cloth. NEVER use solvents to clean plastic parts. They could PROTECTING CAST IRON FROM RUST possibly dissolve or otherwise damage the material. To clean and protect cast iron tables from rust, you will Wear ANSI Z87.1 safety glasses whil
ページ20に含まれる内容の要旨
PORTER-CABLE • DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE • DELTA) Parts and Repair Service for Porter-Cable • Delta Machinery are Available at These Locations (Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta) ARIZONA Tampa 33609 MICHIGAN Cleveland 44125 Tempe 85282 (Phoenix) 4538 W. Kennedy Boulevard Madison Heights 48071 (Detroit) 8001 Sweet Valley Drive 2400 West Southern Avenue Phone: (813) 877-9585 30475 Stephenson
