ページ1に含まれる内容の要旨
Cutout Tool
MODEL 3706
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
ページ2に含まれる内容の要旨
SPECIFICATIONS Collet chuck capacity No load speed (RPM) Overall length Net weight 1/4”, 1/8” 32,000/min. 250 mm (9-7/8”) 1.1 kg (2.4 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS
ページ3に含まれる内容の要旨
damaged cords immediately. Damaged 16. Do not force tool. Use the correct tool for cords increase the risk of electric shock. your application. The correct tool will do the job better and safer at the rate for which it is 8. When operating a power tool outside, use designed. an outdoor extension cord marked “W-A” or “W”. These cords are rated for outdoor 17. Do not use tool if switch does not turn it use and reduce the risk of electric shock. on or off. Any tool that cannot be controlled with th
ページ4に含まれる内容の要旨
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num- ber, the heavier the cord. Table 1: Minimum gage for cord V
ページ5に含まれる内容の要旨
10.Always use with the shoe securely 16. Always switch off and wait for the bit to attached to the tool and positioned flat come to a complete stop before removing and firmly against the workpiece. the bit from workpiece. 11. Hold the tool firmly. 17. Do not touch the bit or the workpiece immediately after operation; it may be 12. Do not perform any operation using your extremely hot and could burn your skin. hands to support or guide the workpiece. 18. Always lead the power supply cord away 13.
ページ6に含まれる内容の要旨
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 001624 Adjusting depth of cut To adjust the shoe, turn the thumb screw to loosen. Slide the 1 shoe to the desired position and tighten the thumb screw 2 securely. Check for the proper clearance beneath the work- piece before cutting so that the bit will not strike a hard sur- face such as the floor, workbench, etc. 1. Shoe 2. Thumb screw Switch action C
ページ7に含まれる内容の要旨
• When using the bit with 6.35 mm (1/4”) shank diameter, first remove the adapter from the collet cone, then install the bit. 001626 To install the bit, insert the bit all the way into the collet cone. 4 Press the shaft lock to keep the shaft stationary and use the 1 5 6 wrench to tighten the collet nut securely. 2 To remove the bit, follow the installation procedure in reverse. 3 7 1. Bit 2. Collet nut 3. Shaft lock 4. Adapter 5. Wrench 6. Loosen 7. Tighten OPERATION CAUTION: • Avoid forcing th
ページ8に含まれる内容の要旨
001629 When inserting the drywall guide bit into the drywall, care- fully insert the bit straight until the shoe base is in full contact with the material. Move the tool slowly with a constant pressure in a clockwise direction to make the cut. 001630 When cutting straight line, clamp a straight board firmly to the material and use it as a guide. Move the tool in the direc- tion of the arrow with the shoe base flush with the side of the guide board. When the cut is complete, turn the tool off and
ページ9に含まれる内容の要旨
001632 Align the projections in the circular guide with the grooves in 2 the shoe, and secure the shoe and circular guide using the 3 thumb screw. 1 1. Shoe 2. Circular guide 3. Projections 001633 To adjust the cutting depth, proceed first by loosening the 2 thumb screw and then by sliding the shoe and circular guide together. After completion of the adjustment, tighten the 3 thumb screw securely. 1 1. Shoe 2. Circular guide 3. Thumb screw OPERATION 001634 Operation Loosen the knob, and adjust i
ページ10に含まれる内容の要旨
Vacuum cover Cleaner operations can be performed by connecting the cut- out tool to Makita vacuum cleaner or dust collector. OPERATION 001636 Installing vacuum cover 1 Loosen the thumb screw and remove the shoe. Attach the vacuum cover, and fasten it securely using the thumb screw. 2 1. Thumb screw 2. Vacuum cover OPERATION 001637 Installing vacuum cover with circular guide 1 Release the thumb screw which serves to secure the vac- 2 uum cover. Align the projections in the circular guide with the
ページ11に含まれる内容の要旨
001639 Connecting to Makita vacuum cleaner or dust 1 collector Connect the hose of a vacuum cleaner/dust collector to the 2 dust nozzle. When connecting to Makita vacuum cleaner, an optional hose 28 mm (1-1/8”) in inner diameter is necessary. 3 1. Vacuum cover 2. Hose 28 3. Hose for vacuum cleaner 001640 When connecting to Makita dust collector, connect the hose 1 for the dust collector directly to the dust nozzle. 2 3 1. Vacuum cover 2. Hose 28 3. Dust collector MAINTENANCE CAUTION: • Always b
ページ12に含まれる内容の要旨
ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. • Collet cone 1/4” • Adapter 1/8” - 1/4” • Drywall guide bit 1/4” and 1/8” • Wrench 17 • Circular guide • Vacuum
ページ13に含まれる内容の要旨
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
ページ14に含まれる内容の要旨
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
ページ15に含まれる内容の要旨
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA COLORADO LOUISIANA NEW YORK PUERTO RICO 2365 Pelham Parkway 11839 E. 51st Ave. 5626 Jefferson Hwy. 4917 Genessee Street 200 Guayama St. Pelham, AL 35124 Denver, CO 80239-2709 Harahan, LA 70123 Cheektowaga, NY 14225 Hato Rey, PR 00917 (205) 620-1791 (303) 371-2850 (504) 733-4138 (716) 685-9503 (787) 250-8776 131-35 31st Ave. ARIZONA FLORIDA MARYLAND Flushing, NY 11354 TENNESSEE 3707 E. Broadway Rd., Ste. 6 62
ページ16に含まれる内容の要旨
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
