ページ1に含まれる内容の要旨
This Manual is Bookmarked
Owner's Manual
®
XACTA Fence II Commercial 30/50
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123 Part No. M-708950Z
Ph.: 800-274-6848 Revision H 03/06
www.wmhtoolgroup.com Copyright © WMH Tool Group
ページ2に含まれる内容の要旨
WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or ® perform routine maintenance and major repair on your JET tools. For the name of an Authorized Service Center in your area call 1-800-2
ページ3に含まれる内容の要旨
Table of Contents WARRANTY AND SERVICE ........................................................................................................................2 Table of Contents..........................................................................................................................................3 Warnings .......................................................................................................................................................4 Ordering Replace
ページ4に含まれる内容の要旨
Warnings 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. The Table Saw on which the XACTA Fence II is used is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper a
ページ5に含まれる内容の要旨
21. Keep visitors a safe distance from the work area. Keep children away. 22. Make your workshop child proof with padlocks, master switches or by removing starter keys. 23. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 24. Maintain a balanced stance at all times so that you do not fall into the blade or other moving parts. Do not overreach or use excessive force to perform any machine op
ページ6に含まれる内容の要旨
Unpacking Open shipping cartons and check that all parts are intact. Report any damage immediately to your distributor. Read the instruction manual thoroughly for assembly, alignment, and maintenance instructions. Contents of the Shipping Containers 1 XACTA Fence II 1 Front Rail 1 Rear Rail 1 Guide Rail 3 Black Plastic End Caps 1 Hardware Package 1 Owner’s Manual 1 Warranty Registration Card The contents of the hardware bag are drawn full scale in Figure 1. Note 1: Quantit
ページ7に含まれる内容の要旨
Installation Tools required 7/16" and 1/2" wrenches Cross point screwdriver 3/16" hex wrench Adjustable square Hammer (or rubber mallet) Straight edge The following instructions are for installing the XACTA Fence II and Rail System on JET Models JTAS-10 and JTAS-12 series table saws. The Rails should bolt up to the JET saw without any drilling. Figure 1 Front Rail Installation Referring to Figures 1 and 2: 1. Identify the front rail (E), which is 2-1/
ページ8に含まれる内容の要旨
Back Rail Installation 1. Locate the back rail which is 2" x 2" with holes running along one side only. The height of the back rail when attached to the saw is not critical. 2. Align the holes in the back rail to the holes in the table top, as shown in Figure 4. Figure 4 3. Secure the back rail to the pre-tapped holes in the saw table (B, C, Fig. 4) with two 5/16 x 3/4 hex cap screws and two 5/16 flat washers, as shown in Figure 5. Tighten screws securely with a 1/2
ページ9に含まれる内容の要旨
Wooden Extension Table The wooden extension table is an optional accessory. Tools required Electric drill Cross point screwdriver 7/16" and 1/2" wrenches Four clamps Straight edge Hammer (or rubber mallet) Figure 7 Installation The optional wood extension table (including the optional router table) sits flush against the saw table and along the inside of the rails. The JET logo (or warning label on the router table) should face outward. The extension table is not bolted to
ページ10に含まれる内容の要旨
as shown in Figure 10. Finger tighten only. 5. Install three 1/4-20 x 1-1/2 hex cap screws, three 1/4 flat washers, and three 1/4 nuts into the holes in the rear edge of extension table as shown in Figure 11. Finger-tighten only. 6. Re-check the table for alignment, make further adjustments if necessary, then tighten all screws and nuts. Figure 11 7. Mount the two legs to the inside corners of the extension table as shown in Figure 12. Secure with the eight screws provided.
ページ11に含まれる内容の要旨
XACTA Fence Screw the lock lever knob into the threaded handle on the XACTA Fence II as shown in Figure 14. The lock lever has three functional positions as shown in Figure 15: • The upright position permits mounting and removal of fence from the saw. • The unlock position permits easy fence Figure 14 positioning. • The lower position locks the fence to the front rail. The cam handle should be pushed down firmly against the pin. Leveling Fence to the Saw Table 4
ページ12に含まれる内容の要旨
Adjusting Fence Parallel to the Miter Slot 1. Place the fence next to the outside edge of the right miter slot and lock it. 2. The fence should be even with the miter slot from front to back. 3. If the fence is not even along the length of the miter slot, unlock the fence, remove it and turn upside down. 4. Adjust one of the two setscrews (A, Fig. 18) until the fence is even with the miter slot edge along its entire length when locked. Note: You may need to re-adjust the clampi
ページ13に含まれる内容の要旨
Parts for the XACTA Fence II Commercial 30/50 Index No. Part No. Description Size Qty 1 ...............XF2-101 ...................Left Side Plate...................................................... .................................... 1 2 ...............XF2-102 ...................Fence Body Assembly ......................................... .................................... 1 3 ...............XF2-103 ...................Tube Cover ........................................................
ページ14に含まれる内容の要旨
Parts for the XACTA Fence II Rail Assembly Index No. Part No. Description Size Qty 1 ...............XF2-201 ...................Front Rail (50”)..................................................... .................................... 1 .................XF2-201A.................Front Rail (30”)..................................................... .................................... 1 2 ...............TS-081F081 .............Flat Head Screw .................................................. 1
ページ15に含まれる内容の要旨
Parts for the XACTA Fence II Leg Assembly Index No. Part No. Description Size Qty 1 ...............XF2-301 ...................Leg ....................................................................... .................................... 2 2 ...............TS-0561031 .............Hex Nut ................................................................ 3/8”-16......................... 2 3 ...............XF2-303 ...................Adjusting foot ...............................................
ページ16に含まれる内容の要旨
WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.com 16
