ページ1に含まれる内容の要旨
®
WINEGARD
®
TRAV’LER
Automatic Multi-Satellite TV Antenna
®
Model SK-3005 DIRECTV SLIMLINE
INSTALLATION MANUAL
Made in the U.S.A.
SK-3005
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
319/754-0600 • FAX 319/754-0787 • www.winegard.com
Printed in U.S.A. © Winegard Company 2008 2452133 Rev. 1/10
ページ2に含まれる内容の要旨
Congratulations! ® You have selected the Winegard TRAV’LER Automatic Multi-Satellite TV Antenna. The TRAV’LER antenna will deliver the ability to view up to five satellites at the same time with unmatched signal strength, the lowest travel height on the market, maximum HD capabilities and easy to use functionality – just like you get at home. This manual provides important information on the installation and operation of your TRAV’LER Interface Box. Please take time to read the manual in
ページ3に含まれる内容の要旨
FRONT OF RV FRONT FRONT OF RV BACK Plan your entire installation before 3/16” you start. Determine the location of all of your equipment and make sure cable and wires are long enough to reach their destination points. You must find a location on the roof that provides adequate space to allow the TRAV’LER antenna to operate. The TRAV’LER antenna has a Front and Back and must be mounted correctly to avoid dam- age to the TRAV’LER antenna or the coach. The antenna must be mounted +/-5 degrees
ページ4に含まれる内容の要旨
FRONT OF RV FRONT 18 inches 3. The unit must be within 3° of level for best operation. 4. Make sure that the location offers enough support to attach the TRAV’LER antenna securely. 5. Find a well ventilated location with a 110 V outlet for the TRAV’LER Interface inside the vehicle. Make sure to clean the installation area before you begin. You will want to decide where the wires will enter the vehicle. One coax cable per receiver and a control cable will need to be run into the vehicle. Warnin
ページ5に含まれる内容の要旨
FRONT OF RV FIGURE 4 DO NOT SEAL ! LIP OF TRANSITION WARNING: DO NOT cut any PLATE wires when you drill the hole for your cables. SEAL Run a solid bead of sealant around the transition plate, making sure to cover each screw head. Be careful not to get any sealant above the lip of the transition plate. See diagram of transition plate. Cable Entry Plate Installation: Winegard recommends in- Decide the best location for the cables to enter the vehicle. stalling the Accessory Detect Cable, t
ページ6に含まれる内容の要旨
Cable installation: Connect the control cable and power cable to the back of the TRAV’LER Interface box as shown below. Note: For cable runs longer than 25’ an extension may be purchased. Do not exceed 50’ of cable. Power Control Cable FIGURE 5A Attach the TRAV’LER control cable to the TRAV’LER Interface Box, as shown in Figure 5A. Attach the output cable from the Power supply to the TRAV’LER Interface Box. See above. Finally, connect a coax cable from the TRAV’LER mount to each of the receive
ページ7に含まれる内容の要旨
A. Press [ENTER] the TRAV’LER will return to the “Installation Menu” OR B. Press [POWER] the TRAV’LER will stow and turn “OFF” (Restart at Step 1). 1. Press [POWER] and hold for 2 seconds to turn “ON” the TRAV’LER Interface Box. Wait until the Interface Box finishes “connecting to antenna”. * The TRAV’LER may enter the “Search Routine” after 10 seconds this is normal (See NOTE Below). 2. Press [ENTER] and hold for 2 seconds or until the unit displays “Enter User Menu”. Press [SELECT] to mo
ページ8に含まれる内容の要旨
WARNING: Pay attention to these Pinch Points as the antenna raises! Pinch Point FIGURE 6 FIGURE 7 Pinch Points Pinch Point Using the (4) bolts and nuts provided, attach the reflector to the mounting bracket. Press [POWER] to lower the antenna to the travel position. Note: The nuts securing the dish should be tightened to 6-8 lb.ft. Receiver Setup: If you are not able to see all of your channels or the receiver displays an error, it may be necessary to go through the receiver set up once the
ページ9に含まれる内容の要旨
Appendix: Making the Right Connection with Hex Connectors Making a coaxial cable connection is critical. If you have the basic technique right you can modify it to your own personal taste. Whether you use a knife, stripping tool or diagonal cutter, the important thing is to make a good clean cut. A hex crimping tool is required for hex connectors, for maximum RF transmis- Remove additional 1/4” of the outer Cut the cable flush. Strip the outer sion. jacket.Pull the braid away from the ja
ページ10に含まれる内容の要旨
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY (2 YEARS PARTS; 1 YEAR LABOR) Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the date of original purchase. During year one (1) of such warranty, Winegard Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace defective products. No warranty claim will be honored unless at the time the claim is made, Customer presents proof of purchas
ページ11に含まれる内容の要旨
INSTALLATION 11
ページ12に含まれる内容の要旨
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000 319/754-0600 • FAX 319/754-0787 • www.winegard.com Printed in U.S.A. © Winegard Company 2008 2452133 Rev. 1/10
