ページ1に含まれる内容の要旨
®
WINEGARD
TM
Movin’ View
Digital Satellite Mobile Antenna for Single Receiver
Model MV-0055
Made in the U.S.A. U.S. Patent Nos. 6,023,247; 6,188,300
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
319/754-0600 • FAX 319/754-0787 • www.winegard.com
Printed in U.S.A. © Winegard Company 2002 2451022 1/02
1
ページ2に含まれる内容の要旨
Introduction/How Does Digital Satellite TV Work? Introduction and processing take place. Congratulations! You have purchased one of Winegard’s latest developments in the mobile satel- For Programming information call: TM TM lite reception product line —the Movin’ View . DISH NETWORK - 1-800-333-DISH (1-800-333-3474) This system, used with your digital satellite receiver, ® DIRECTV - 1-800-DIRECTV (1-800-347-3288) will deliver the best reception possible using GPS (Global Positioning System) and
ページ3に含まれる内容の要旨
Parts Included • Tools Needed • How to Unpack About this manual — We hope this manual will provide clear instructions to install and operate MV-0055. Two symbols have been used — Indicates suggestions to make Indicates caution should be taken! ! processes easier for you. NOTE: The MV-0055 can only be used with one (1) receiver. For multiple receiver use, contact Winegard for information on available Upgrade Kits. PARTS INCLUDED: 1 Radome 1 large yellow spade connector 3 base mounting feet 2 smal
ページ4に含まれる内容の要旨
Installation Diagram GPS ANTENNA FIGURE 1 SWITCH LOCATION ADJUSTABLE EL MOTOR ® HEYCO CONNECTORS BASE FOOT POWER SUPPLY LEVELING COUNTERWEIGHT SCREW LEVELING SCREW REAR ADJUSTABLE BASE FOOT LEVELING SCREW REAR BASE FOOT MUST DIRECTLY FACE REAR OF VEHICLE AZ MOTOR ADJUSTABLE BASE FOOT REFLECTOR 4 Remove wire ties holding mount !!! !! FRONT OF VEHICLE
ページ5に含まれる内容の要旨
Installation Installing unit on roof of vehicle — 6. On each foot, screw the flange nut to the base of the leveling screw on the mounting foot, flange up. Install in DRY conditions only! Place rubber washer, with the rubber side up, on ! the nut, Figure 2. Push mounting foot under base. IMPORTANT! Do not install this system Push foot screw through the base and tighten lock in the rain, or under any wet conditions. Moisture nut to secure foot to base. Be sure the base feet are may affect electron
ページ6に含まれる内容の要旨
Installation ROOF INSTALLATION, continued GPS installation — 9. Place the unit on the roof in its permanent location The GPS antenna is pre-wired and has a 3 foot cable ® and mark around the base bracket, Figure 4. (Make running through one of the Heyco connectors. sure the rear adjustable base foot is directly facing When deciding where to place GPS antenna, DO the back of the coach.) NOT SECURE! After wiring the receiver and initializ- FIGURE 4 ing your system, you will need to test the system
ページ7に含まれる内容の要旨
Installation • Wiring Cable entry installation — 1. Decide the best location for the cables to enter the Connecting the receiver — vehicle, and the location of the switch and receiver 1. Connnect the coax cable from the roof to the “Sat- (see “Installing the switch and receiver” below.) Drill ellite In” connection on the receiver. a 1/2” hole in the roof, push wires inside. Make proper connections (remember you must have fil- tered +12 VDC power source). 2. Place cable-entry plate over hole and
ページ8に含まれる内容の要旨
Operation Your new MV-0055 features: • GPS technology satellite programming • Fast signal acquisition times • Low maintenance • Easy “one-button” operation • Compatible with most digital satellite receivers • Ability to toggle between satellites using • Winegard warranty remote control, if subscribing to multi- To operate your system — NOTE: For Model MV-0055, vehicle must be parked. NOTE: Acquisition time will be longer if the vehicle has traveled more than 600 miles without the unit in us
ページ9に含まれる内容の要旨
Troubleshooting NOTE: The power rocker switch must be ON for the IF YOU DO NOT HAVE A SIGNAL: next steps. Voltage must be +12 VDC, except at the 1. The signal may be blocked by trees, hills or LNBF, see #2, Figure 9, page 10. structures. Pull into an area where no trees or buildings are in the line of sight from unit to the 6. To check voltage at connections, see Figure 9 on satellites. page 10. FOLLOW THE NUMERICAL SE- QUENCE ON THE DRAWING AND CHECK 2. Check your +12 VDC power switch. Make VO
ページ10に含まれる内容の要旨
Base Diagram FIGURE 9 GPS ANTENNA #3 CONTROL #1 POWER SUPPLY HEYCO CON- #4 COAX CABLE AT BOX TO LNBF NECTORS CONTROL BOX (POWER WIRE, SEE DETAIL) EL MOTOR GPS POWER SUPPLY CONTROL BOX (DETAIL BELOW) #2 LNBF VOLTAGE AZ MOTOR CONTROL BOX DETAIL DO NOT USE EL MOTOR AZ MOTOR 10 A T TO LNBF TO RECEIVER 8-PIN POWER
ページ11に含まれる内容の要旨
Notes Features and specifications MV-0055 • One button operation. • GPS satellite signal acquisition. • Depending on receiver type, you can access satellites 119°, 110°, 101° or 92°. • No user input required. TM • No data port required for DISH Network , ® DIRECTV or ExpressVu. • Tracking greater than 30°. • Elevation range 14.5° to 74.5°; azimuth unlimited. • 30’ power cable and 30’ coaxial cable included. • Manufactured from sturdy ABS plastic, UV protected. • Off-white color compatible with a
ページ12に含まれる内容の要旨
Specifications & Warranty Features and specifications • One button operation. • 30’ power cable and 30’ coaxial cable included. • GPS satellite signal acquisition. • Manufactured from sturdy ABS plastic, UV protected. • Depending on receiver type, you can access satellites 119°, 110°, 101° or 92°. • Off-white color compatible with all vehicles. • No user input required. • Compact size — 32” diameter, 15” height TM • No data port required for DISH Network , Weight of unit - 43 lbs. ® DIRECT
