ページ1に含まれる内容の要旨
Operating manual
- Englisch -
DVB Satellite Receiver
UFS 740sw
ページ2に含まれる内容の要旨
PREFACE Dear customer, This operating manual is intended to help you make the fullest use of the extensive range of functions offered by your new satellite receiver. We have tried to make the operating instructions as easy as possible to understand, and to keep them as concise as possible. To help you understand particular specialist terms that cannot be translated, we have added a short glossary at the end of the manual. The power switch is an environmentally friendly feature. If you will no
ページ3に含まれる内容の要旨
IMPORTANT INFORMATION The channels available on the satellites and transponders are subject to continual change. If changes do occur, the new channels have to be set in the receiver because the factory preset programming corresponds to the status on the date of manufacture. The information for these settings can be found on the Internet or in relevant magazines. Your receiver is factory fi tted with the latest software version. We are, however, constantly working on adapting the software in r
ページ4に含まれる内容の要旨
CONTENTS PREFACE ................................................................................................................................. 2 IMPORTANT INFORMATION ...................................................................................................... 3 CONTENTS ............................................................................................................................... 4 SAFETY INSTRUCTIONS - IMPORTANT NOTES ..............................................
ページ5に含まれる内容の要旨
CONTENTS EDIT CHANNEL LIST ............................................................................................................... 53 SELECTION OF THE LIST/CHANNELS TO BE EDITED ............................................................ 53 EDITING LISTS/CHANNELS ................................................................................................... 54 “LAST FUNCTION” MEMORY .................................................................................................. 55
ページ6に含まれる内容の要旨
SAFETY INSTRUCTIONS - IMPORTANT NOTES 6
ページ7に含まれる内容の要旨
RECEIVER FEATURES/SCOPE OF SUPPLY The receiver UFS 740sw is suitable for the reception of digital satellite TV and radio channels. The integral Common Interface has slots for two CA modules for decrypting Pay-TV programmes. In addition to providing high-quality pictures and sound, UFS 740 units also feature an attractive design and 16-character display. The external power supply unit means that the unit can be operated on both 12 V and on 230 V. A mounting kit for fl at or suspended mounting
ページ8に含まれる内容の要旨
CONTROLS, DISPLAYS AND CONNECTIONS This section provides a brief description of all the controls, displays and connections. VIEW OF FRONT PANEL (FLAP FOLDED DOWN) VIEW OF REAR PANEL Front panel controls and displays Rear panel controls and displays 1. On/Off switch (with mains disconnect) 1. LNB input 2. Display (cover folded down) 2. Optical data stream output (SPDIF/ 3. Common Interface for two Sony Philips Digital Interface Format) ) CA modules for Pay-TV cards * for Dolby Digital AC
ページ9に含まれる内容の要旨
CONNECTION AND SET-UP The following section is intended specifi cally for specialist dealers. You only need to pay attention to this section if you are carrying out the installation yourself. The “Connection Examples” section provides a sample confi guration. Do not connect the unit to the power supply until all installation work has been properly carried out. Refer to the information in the “Safety Instructions” section. The receiver must be connected to no other power supply than 12 V DC. The
ページ10に含まれる内容の要旨
CONNECTION AND SET-UP TV AND VIDEO RECORDER CONNECTION Connect the satellite receiver (Cinch socket) and the TV set (Scart socket) using the Cinch to Scart cable supplied, or connect both units (Scart sockets) using a Scart cable (see “Connection Example”). If your TV has a stereo feature, you can receive the sound in stereo via the Scart connection. Use a further Scart cable to connect the satellite receiver (VCR/Scart socket) to the video recorder/PVR. For system reasons, the same video sig
ページ11に含まれる内容の要旨
CONNECTION AND SET-UP SUSPENDED INSTALLATION Remove the wood screws supplied from their transport attachment on the underside of the respective mounting piece (2 pieces). Vertically insert each mounting piece into the fi fth slot from the edge, as shown in Fig. 1. Then push each mounting piece downwards and outwards (see Fig. 2) until they lie fl at on the receiver casing (see Fig. 3). Now press the mounting pieces fi rmly against the receiver casing at the points shown arrowed in Fig. 3), u
ページ12に含まれる内容の要旨
REMOTE CONTROL Sound on/off Stand-by ... Videotext (Teletext) Switch on/input digits for channels, timer etc. (yellow) Call up channel options Call up the main menu, sound/subtitles selection exit the menu and return to the TV picture (blue) Switch between TV/radio (red) Call up favourites selection Call up channel messages channel information (green) “Current” view in the EPG AV mode Volume Channel selection up/down Exit menu step by step Input confi rmation call up cha
ページ13に含まれる内容の要旨
REMOTE CONTROL REMOTE CONTROL RC 660 The RC 660 remote control supports up to four devices (which are supplied with the RC 660 as standard) as well as the receivers of the UFD 5xx (not UFD 552, 554, 558) and UFD 4xx families. First switch all receivers off (at the power switch). To confi gure a receiver to an infrared code: Switch on the relevant receiver. On the remote control simultaneously press Address 1 = + + . Then switch the receiver off again at the power switch and do the same for
ページ14に含まれる内容の要旨
FIRST INSTALLATION Before using your unit for the fi rst time, read the “Safety Instructions” and “Connection and Set-Up” sections. The “Connection Examples” section provides a sample confi guration. Do not connect the unit to the power supply until all installation work has been properly carried out. The guidance given in the “First Installation” section assumes that the receiver has been properly connected, as per the “Safety Instructions” and “Connection and Set-Up” sections. First switch y
ページ15に含まれる内容の要旨
FIRST INSTALLATION Use the buttons to select whether to replace the default channel list with one pre-sorted for Germany, Austria, Switzerland or Italy. If you want to use the default channel list, choose “No” under “Restore Channellist”. Press the (green) button to move to the next menu. The following display appears: Use the buttons here to select the settings for your TV set. When doing this, refer to the operating instructions for your TV set! TV format Select the TV‘s picture forma
ページ16に含まれる内容の要旨
FIRST INSTALLATION Screen display Here you select the type of screen display, depending on the setting of your TV format: - TV format “4:3”: Pan & Scan or Letterbox - TV format “16:9”: Always 16:9 or automatic TV Scart signal output Select the type of video signal at the TV Scart socket here. Select the signal that your TV set can process. - CVBS – Colour Video Baseband Signal - RGB – Red/Green/Blue signal or - Y/C – S-Video signal (luminance/chrominance) Press the (green) button to move to the
ページ17に含まれる内容の要旨
FIRST INSTALLATION When selecting the satellite(s), make sure that your reception position is aligned to the desired satellite(s)! The fi rst installation with a CAP 900 automatic turntable unit is explained in the installation manual supplied with the turntable unit. System Select the setting here to match your reception system using the buttons. If your reception system is DiSEqC™-capable, at System select “DiSEqC™ 1.0” (allows switch-over from receiving one satellite to receiving
ページ18に含まれる内容の要旨
FIRST INSTALLATION LNB settings Use the buttons to select how many satellites (max. 4) you would like to receive with your Here use the buttons to select the LNB reception system. The following display appears type used in your system. The choice is between (example): “Universal” and “User-defi ned”. Universal: No further input required, since all necessary frequency ranges are covered by a universal LNB. User-defi ned: If you choose not to use a universal LNB, you must here set the fre
ページ19に含まれる内容の要旨
FIRST INSTALLATION Satellites and position Use the buttons to set the desired satellite (selection from 17 pre-programmed options). LNB settings Here use the buttons to select the LNB type used in your system. The choice is between “Universal” and “User-defi ned”. Universal: No further input required, since all necessary frequency ranges are covered by a universal LNB. User-defi ned: If you choose not to use a universal LNB, you must here set the frequency ranges for which your LNB was c
ページ20に含まれる内容の要旨
FIRST INSTALLATION: One cable Use the buttons here to select “One cable” as the “System”. Press the button to move to the next menu item. The following display appears: The various options for a single-cable system with Kathrein components are summarised at the end of this manual in the “Technical Appendix” sectionunder “Examples of Single-Cable Systems”. Number of satellites Use the buttons to select how many satellites (max. 2) you would like to receive with your reception syste
