ページ1に含まれる内容の要旨
A Guide to TracVision L2
owner’s
manual
•
Installation Instructions
•
User’s Guide
•
Technical Manual
®
KVH TracVision L2
Satellite Television
ページ2に含まれる内容の要旨
TracVision L2 Owner’s Manual Addendum (ECO #6119) The following information applies to Revision A of the TracVision L2 Owner’s Manual (KVH Part Number 54-0195). Aprotective cover has been added to the switchplate to guard against damaging electrostatic discharges (ESD), which may occur during installation. Figure 2-11 Switchplate Cutout Dimensions 2.3 Connecting System Components 2" Figure 2-11 and the template on the following page have been changed to show the new switchplate cutout dimensio
ページ3に含まれる内容の要旨
Appendix C Switchplate Template 2" 2.5" 54-0195 Addendum to Rev. A 2
ページ4に含まれる内容の要旨
A Guide to TracVision L2 – ADDENDUM TracVision L2 Owner’s Manual Addendum (ECO #6040) The following information applies to Revision A of the TracVision L2 Owner’s Manual (KVH Part Number 54-0195). 2 Installation Kitpack Contents Two plugs have been added to the kitpack for sealing the predrilled holes in the antenna baseplate. Part Qty. KVH Part No. Table 2-2 Kitpack Contents Switchplate assembly 1 02-1236-01 Tie-wraps 5 22-0013 RJ11 handset cable 1 32-0724-25 Clam shell ventilator 1 19-0230 3
ページ5に含まれる内容の要旨
Congratulations! You have selected one of the most advanced land-mobile satellite ® ® tracking systems available today. KVH Industries’ TracVision L2 ® ™ is designed for use with DIRECTV , DISH Network , and ExpressVu. This manual provides detailed instructions on the proper installation, use, and maintenance of your TracVision L2 system. Throughout this manual, important information is marked for your attention by these icons:
ページ6に含まれる内容の要旨
® ® TracVision and KVH are registered trademarks of KVH Industries, Inc. ® DIRECTV is an official trademark of DIRECTV, a unit of GM Hughes Electronics Corporation. ™ DISH Network is an official trademark of EchoStar Communications Corporation. ExpressVu is a property of Bell ExpressVu, a wholly owned subsidiary of Bell Satellite Services.
ページ7に含まれる内容の要旨
Table of Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1 1.1 Digital Satellite Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1 1.2 TracVision L2 System Overview . . . . . . . . . . . . . . . . . . . . . . . . .1-1 1.2.1 TracVision L2 Components.....................................................1-2 1.2.2 Integrated Receiver/Decoder (IRD) ........................................1-2 1.3 Materials Provided with TracVision L2 . . .
ページ8に含まれる内容の要旨
3.2.1 Using the IRD for Satellite Selection ......................................3-3 3.2.2 Using the Switchplate for Satellite Selection..........................3-3 3.2.2.1 The Status Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3 3.3 Turning Off the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4 3.4 Watching Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4 4Troubleshooting . . . . . . . . . . . . . . . . . . . .
ページ9に含まれる内容の要旨
5.4.2 Antenna Gyro Assembly.........................................................5-6 5.4.3 Antenna LNB Replacement....................................................5-8 5.5 Preparation for Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-10 Appendix A System Specifications . . . . . . . . . . . . . . . . . .A-1 Appendix B Comprehensive TracVision L2 System Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . .B-1 Appendix C Switchplate Template . . . . . . . . . . .
ページ10に含まれる内容の要旨
Figure 2-9 Rotating Plate Shipping Restraint Storage . . . . . . . . . . . .2-7 Figure 2-10 TracVision L2 Shipping Restraints (Storage Position) . . . .2-7 Figure 2-11 Switchplate Cutout Dimensions . . . . . . . . . . . . . . . . . . . .2-8 Figure 2-12 Antenna Baseplate Connectors . . . . . . . . . . . . . . . . . . . .2-8 Figure 2-13 Switchplate Connectors . . . . . . . . . . . . . . . . . . . . . . . . . .2-9 Figure 2-14 Installing Three or Four IRDs Using an Active Multiswitch . . . . . . . .
ページ11に含まれる内容の要旨
Table 3-1 Status Indicator Conditions . . . . . . . . . . . . . . . . . . . . . .3-3 Table 4-1 Troubleshooting Matrix . . . . . . . . . . . . . . . . . . . . . . . . .4-1 Table 5-1 Field Replaceable Units . . . . . . . . . . . . . . . . . . . . . . . .5-2 Table A-1 TracVision L2 System Specifications . . . . . . . . . . . . . . .A-1 Table F-1 System Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . .F-1 Table F-2 Manual Positioning Commands . . . . . . . . . . . . . . . . . . .F-2 T
ページ12に含まれる内容の要旨
Introduction 1 Introduction 1.1 Digital Satellite Television ® ™ DIRECTV , DISH Network , and ExpressVu systems transmit digital audio and video data from land-based transmitters to a satellite “parked” above the equator. Each satellite relays the signals in spot beams covering the continental United States and contiguous waters. TracVision L2 automatically identifies, locks onto, and tracks signals from the appropriate satellite, both while your vehicle is at rest and in motion. 1.2 TracVision
ページ13に含まれる内容の要旨
A Guide to TracVision L2 1.2.1 TracVision L2 Components The antenna unit includes the antenna positioning mechanism, signal front end, power supply and control elements. These elements include antenna drive controls and mechanisms, the cable wrap subassembly, antenna gyro sensor, power conditioning and regulating circuits, and the RF detector. The antenna is a parabolic dish mounting a dual-output low noise block (LNB) converter with built-in preamplifier. A molded ABS radome encloses the basepl
ページ14に含まれる内容の要旨
Introduction 1.3.1 Additional Materials Required for TracVision L2 Use To make full use of your new TracVision L2 and receive satellite TV, you will need to provide/purchase the following: • Television You can purchase and activate an • Appropriate IRD for your selected satellite IRD directly from KVH! Call KVH at TV service 1-888-584-4163 for details. 54-0195 Rev. A 1-3
ページ15に含まれる内容の要旨
Installation 2 Installation TracVision L2 is designed for simple installation and setup. Just follow these easy steps: Table 2-1 Step Refer to Section... Installation Process 1. Choose the antenna location 2.1 2. Mount the antenna unit 2.2 3. Connect the system components 2.3 4. Activate the IRD 2.4 5. Check out the system 2.5 Tools and Materials Required Plan the entire installation before • Electric drill proceeding! Take into account component placement, cable 3 3 • ⁄16"-drill bit and ⁄4" hol
ページ16に含まれる内容の要旨
A Guide to TracVision L2 Kitpack Contents Table 2-2 lists the materials provided in the kitpack. Table 2-2 Part Qty. KVH Part No. Kitpack Contents Switchplate Assembly 1 02-1236-01 Tie-wraps 5 22-0013 RJ11 Handset Cable 1 32-0724-25 Clam Shell Ventilator 1 19-0230 3 #6 x ⁄4" Thread-forming Screws 5 14-0298-12 1 5 ⁄4"-20 x ⁄8" hex screws 4 14-0250-10 1 ⁄4" flat washers 4 14-0251 2-2
ページ17に含まれる内容の要旨
Installation 2.1 Choosing the Best Location • Since the TracVision antenna requires a clear view of the southern sky to receive satellite signals, the ideal antenna site has an unobstructed view of the horizon/satellite all around. • Keep the antenna clear of any obstructions on the roof (e.g., air conditioners). The antenna requires a 15º to 75º look angle to receive satellite signals. Figure 2-1 Antenna Blockage TracVision Antenna Blocked! Air Conditioner Vehicle Roof • Consider the location o
ページ18に含まれる内容の要旨
Vehicle Centerline Front/Rear of Vehicle A Guide to TracVision L2 2.2 Mounting the Antenna Unit 1. Make sure that you have chosen a suitable mounting location based upon the guidelines in Section 2.1, “Choosing the Best Location.” Always lift the antenna unit by the 2. Remove the antenna unit from its shipping carton. gray baseplate, never by the 3. Position the antenna unit in the desired location radome! on the centerline of the vehicle with the antenna’s mounting plate arrows facing the front
ページ19に含まれる内容の要旨
Installation 8. Reposition the antenna, lining up the mounting plate holes with the holes in the roof. Attach the 3 mounting plates to the roof using ⁄16"-diameter rivets (or appropriate fasteners). Seal all rivet If the roof’s mounting surface is not heads and edges with silicone. perfectly flat as KVH recommends, make sure the baseplate does not 9. Remove and save the 8 pan head screws and flat warp when you attach the washers that secure the radome to the baseplate. antenna’s mounting plates.
ページ20に含まれる内容の要旨
A Guide to TracVision L2 11. Cut the tie-wraps holding the antenna unit to the forward shipping restraint (see Figure 2-6). Figure 2-6 Forward Shipping Restraint (Arranged for Shipping) 12. Remove the nuts and washers securing the shipping restraints to the baseplate. The positions of all three shipping restraints are pictured in Figure 2-7. Figure 2-7 Rotating Plate TracVision L2 Shipping Restraints Ship
