ページ1に含まれる内容の要旨
SIRIUS Home Signal Distribution Kit
for Satellite Radio
For Use With One or Two SIRIUS Radios
Installation Manual
ページ2に含まれる内容の要旨
Thank you for purchasing the SIRIUS Home Signal Distribution Kit for Satellite Radio The SIRIUS Home Signal Distribution Kit for Satellite Radio will allow you to con- nect one or two SIRIUS radios using only one outdoor antenna, with standard RG-6 antenna cable wire, the same cable used in cable TV installations. This allows you great flexibility as to where you locate the outdoor antenna and where you locate your SIRIUS radios. RG-6 cables can be purchased at your local hard- ware store, h
ページ3に含まれる内容の要旨
Tools Required A phillips-type screwdriver and a 3/8 in. wrench is needed for installation. De- pending upon the type of installation, a power drill with a 3/32 in. drill bit may also be required. Caution and Warnings WARNING: Be sure not to cut, damage, or puncture the external jacket of the antenna cables during the installation procedure. Damage to the antenna cable can cause the SIRIUS signal to be degraded or unavailable, and can also cause water to intrude into the antenna cable causin
ページ4に含まれる内容の要旨
Materials Required and Installation Considerations In order to install the antenna you will need to purchase several lengths of RG-6 antenna cables to complete your installation. The following illustration shows a typical home installation. SATELLITE SATELLITE RADIO OUTDOOR ANTENNA Adapter Cable SATELLITE RADIO Adapter Cable SPLITTER S Cables will be needed for the following: 1. A length of RG-6 cable to go from the SIRIUS outdoor antenna to the loca- tion of the Splitter. 2. A length of RG-6
ページ5に含まれる内容の要旨
RG-6 cable is typically sold in lengths of 25, 50, or 100 ft., all with “F” type con- nectors on each end. These cables may be purchased at your local hardware store, home center, or electronics retailer. The combined length of the RG-6 cables from the outdoor antenna to each SIRI- US radio should not exceed 150 ft., as shown in the preceding illustrations. The overall length for your particular installation may be less than 150 ft. Also note that the individual lengths of the cables from the
ページ6に含まれる内容の要旨
on the antenna base and align the screw holes in the mounting bracket with the screw hole in the antenna arm. 4. When the screw hole is aligned, re-insert screw B and snug it until it is tight. 1. 2. BASE ARM Incorrect Incorrect C B Remove Screw Correct Correct Verify the correct orientation of the antenna arm and antenna base 3. 4. Slide the antenna arm over the antenna base mounting bracket B Re-insert screw Align the and tighten screw hole . Determining a Location for the Antenna For cor
ページ7に含まれる内容の要旨
No obstructions to the sky within this area If you cannot obtain a clear 360 degree view of the sky, then you must at least have a clear view of the sky in the direction of the SIRIUS satellites, as shown in the following map diagram. SKY NORTH WEST EAST HORIZON SOUTH Use the above map and find the area you are located in (1 to 5). Then find the direction in which you need to have a clear view of the sky: Area 1: You will need a location with a clear view of the sky facing EAST or NORTHEAST
ページ8に含まれる内容の要旨
Signal Indicator the sky in the direction for your area. For example, suppose you live in Area . You determined that your antenna will need to have a clear view of the sky facing North or Northeast. The exact direction is determined by your specific location in Area relative to the X on the map: If you live in Texas, you will need a more North facing clear view of the sky whereas if you live in southern California, you will need a more Northeast fac- ing clear view of the sky. The follow
ページ9に含まれる内容の要旨
. Antenna Mounting Options There are three possible mounting options for the outdoor antenna, and the antenna mounting location you have chosen may determine which mounting methods you can use: Wall Mount: Mounting the antenna directly on the side of a home or building. Roof Mount: Mounting the antenna on the roof of a home or building. Mast Mount: Mounting the antenna on a mast or pole, such as an existing satel- lite TV dish mast, an existing TV antenna mast, or other mast or pole, not ex-
ページ10に含まれる内容の要旨
MOUNTING HOLES The antenna mounting bracket should be oriented in a vertical position as shown, and mounted directly to the building or home using the provided #10 screws. Once you have determined a suitable mounting location, use the mounting bracket as a template and mark the mounting surface with the location of the four screw holes in the mounting bracket. Then, using a 3/32 in. drill bit, drill pilot holes for the screws. It may be necessary to fill the holes with a small amount of roo
ページ11に含まれる内容の要旨
Slide one of the U-bolts through the holes at the top of the mounting bracket. Then slide one of the mounting brackets over the two legs of the U-bolt. Next, screw the hex nuts on each leg until they are snug. Do not yet tighten the hex nuts beyond finger tight. Repeat this procedure with the other U-bolt. When all the hex nuts are snug, verify that the antenna is facing the correct direction and begin tightening each hex nut with a 3/8” wrench. Turn each hex nut one-half turn and then move
ページ12に含まれる内容の要旨
SKY HORIZONTAL LEVEL Antenna Pod 1 2 Adjustment Screw Adjustment Screw Slightly loosen the adjustment screws and position the antenna so that the top of the antenna pod is level, with the top of the pod horizontal to the sky as shown. When the antenna is adjusted correctly, tighten the adjustment screws but be careful not to overtighten them. Continue with the next section for installations with exposed wiring, or the section following for installations with hidden wiring. Cable Installatio
ページ13に含まれる内容の要旨
you are locating the Splitter. When routing the antenna cable, be careful not to pinch, squash, kink, or crimp the cable, or cut, damage, or puncture the external jacket of the antenna cable. 4. Connect the cable from the antenna to the IN port on the Splitter as shown. (Refer to page 3 for the Splitter port identification.) Note that you must use the Splitter even if you are only connecting one SIRIUS radio. 5. Connect another RG-6 cable to the OUT1 connector of the Splitter and route the
ページ14に含まれる内容の要旨
If you are connecting one SIRIUS radio, the completed installation should be as illustrated below: Home Distribution Kit Installation Manual 1 IN IN OUT1 OUT2 OUT1 OUT2
ページ15に含まれる内容の要旨
Troubleshooting SIRIUS radio displays “Antenna Error” or “Check Antenna” message. Check the antenna cable connections to be sure they are connected tightly. SIRIUS radio displays “No Signal” or “Acquiring Signal” message. The radio is not receiving a good SIRIUS signal. Check that the antenna has a clear view of the sky, and that the antenna is pointed in the direction of the SIRIUS satellites. (See the section titled, Antenna Installation.) This message may also be an indication that your c
ページ16に含まれる内容の要旨
SIRIUS Satellite Radio 1 1 Avenue of the Americas New York, NY 100 0 ( ) 5 - www.sirius.com © 2007 SIRIUS Satellite Radio Inc. (SIRIUS Home Signal Distribution Kit for Satellite Radio 100107a) ® “SIRIUS” and the SIRIUS dog logo are registered trademarks of Sirius Satellite Radio Inc.
ページ17に含まれる内容の要旨
SHDK1 90 DAY LIMITED WARRANTY Satellite Radio Accessory AUDIOVOX ELECTRONICS CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor. To obtain repai
ページ18に含まれる内容の要旨
ページ19に含まれる内容の要旨
ページ20に含まれる内容の要旨
