ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART OESWC-LAN29H
OESWC-LAN29H
07-UP GMLAN29 HARNESS FOR OE RF/STK
The OESWC-LAN29H is to be used with either the OESWC-STK
or OESWC-RF. Please refer to instructions provided with
OESWC-STK or OESWC-RF for mounting instructions.
1-800-221-0932 axxessinterface.com
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
ページ2に含まれる内容の要旨
RF Wiring the OESWC interface 1. Connect the red wire to 12 volt accessory 2. Connect the Black wire to ground (you may use the same ground that you use for the aftermarket radio) Setting up the OESWC transmitter 1. Press the Red and Green buttons simultaneously for 5 seconds, and then press volume up for two seconds. This will orientate your button direction. 2. Turn on the ignition and press volume up on the OESWC transmitter. This will “marry“ the transmitter to the interface. NOTE: If y
ページ3に含まれる内容の要旨
5. This is the end of the auto detection stage. If the OESWC TRANSMITTER detected the vehicles radio successfully the led will light up solid red. 6. Make sure the steering wheel control buttons function correctly in the vehicle and enjoy your radio. So what if the led does not light up solid red? Check out troubleshooting section below. Troubleshooting the Auto Detect Mode So you tried the auto detect feature and at the end the led did not stay on solid red, it started flashin
ページ4に含まれる内容の要旨
STALK Wiring of ASWCSTALK and interface 1. Connect the BLACK wires of the ASWCSTALK and the BLACK wire of the interface to ground. You may use the same ground point that is used for the radio. 2. Connect the GREEN/ORANGE and BLACK/GREEN wires of the ASWCSTALK to the corresponding wires on the interface. 3. Connect the RED wire to 12 volt accessory 4. Tap off all other unused wires on the interface. Programming the ASWCSTALK * If this is the first time the ASWCSTALK is being installed: 1. Turn
ページ5に含まれる内容の要旨
If the ASWCSTALK is mounted on the right side of the steering column follow the instructions below. (Auto-detect must be done first) 1. Turn the ignition on 2. Press the MODE on the ASWCSTALK for 10 seconds 3. Then press volume up for 2 seconds 4. The ASWCSTALK is now configured for the right side Troubleshooting the Auto Detect Mode So you tried the auto detect feature and at the end the led did not stay on solid red, it started flashing, or the steering wheel controls did not function proper
ページ6に含まれる内容の要旨
3 1 5 2 4 1. Volume up 2. Volume down 3. Seek up 4. Seek down 5. Mode (source) 3 1 5 4 2 1. Volume up 2. Volume down 3. Seek up 4. Seek down 5. Mode (source) 5
ページ7に含まれる内容の要旨
NOTES
ページ8に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART OESWC-LAN29H KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians 1-800-221-0932 axxessinterface.com © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION REV. 2/4/11
