ページ1に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7
INSTRUCTION MANUAL
VCC-5984
COLOR CCD CAMERA
About this manual
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
ページ2に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you FEATURES need help with installation and/or settings, please consult your dealer. • Built-in interline transfer method 1/3" CCD, approx. 410,000 picture elements CONTENTS • Equipped with a DSP (Digital Signal Processor) function • Horizontal resolution, more than 520 TV lines INFORMATION TO USER . . . . . . . . . . . . . . .
ページ3に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 INFORMATION TO USER This equipment has been tested and found to comply with the limits Safety Guard for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection THIS SYMBOL INDICATES THAT THERE ARE against harmful interference in a residential installation. This IMPORTANT OPERATING AND MAINTENANCE equipment generates, uses, and can radiate radio frequency INSTRUCTIONS IN THE LITERATURE energy and
ページ4に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 PRECAUTIONS In case of problem Protect from humidity and dust Do not use the camera if smoke or a strange odour comes from the To prevent damages to the camera, do not install it where there is unit, or if it seems not to function correctly. Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust. Service Centre). Protect from high temperatu
ページ5に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 2 Power input terminal 4 1 24 V AC input terminal (AC 24 V, GND) 3 3 External sync composite video signal input connector (VBS IN: BNC type) Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite signal of a video distributor. 2 4 Power indicator (POWER) Comes on
ページ6に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 PARTS NAMES 5 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 6 Flange-back adjustment screw (FLANGE BACK ADJ.) 7 5 7 Flange-back lock screw (FLANGE BACK LOCK) 6 8 8 Camera installation bracket 2 3 2 The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the 1 longer screws and install the shorter screws on the opposite side
ページ7に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 PARTS NAMES 9 Lens iris output connector (LENS) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. F F Camera setup section (under the cover) 9 These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS"). To access the controls, remove the cove
ページ8に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 CONCERNING AUTO-IRIS LENSES DC type auto-iris lens VR301 A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens. (Set the A.I. LENS switch to the DC position.) DC VIDEO VIDEO type auto-iris lens A. I. LENS A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is referred to as EE amplifier ty
ページ9に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). 1 Check the lens mount Do not use a lens if the length “L” is more than 5 mm. That may damage the camera and prevent proper installation. C mount type lens 2 L 1 Remove the lens mount cap from the camera. 2 Install the auto-iris lens. CS mount type lens Carefully align the lens mount with the camera opening, then turn the lens slowly to install it. C mount type lens 3 To allow for flange-b
ページ10に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. 1 Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. Install the lens iris plug. 2 2 Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover. Pin layout DC type lenses VIDEO type lenses Brake coil (–) +12 V DC (50 mA max.) 1 2 1 2 1 Brake coil (
ページ11に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 CONNECTIONS 1 (A) 3 AC 24 V connection Push to insert the cable AC 24 V 2 (Video signal connections) ~ ~ GND : VIDEO IN : VIDEO OUT Coaxial cable type and maximum length Basic connection for monitoring or recording • Cable type RG-59U (3C-2V), 250 m maximum. The peripheral devices (VCR, monitor, lens, etc.), AC adaptor • Cable type RG-6U (5C-2V), 500 m maximum. and cables are sold separately. • Cable type RG-11U (7C-2V), 600 m maximum. 1 Make the
ページ12に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 SETTINGS The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given. 6 7-a 9 Control namePosition High speed electronic shutter (ES) setting 1/60 sec. 1 VR304 R B VR301 VR302 VR303 Gain up setting NORM 2 ON (HI: High/NORM: Normal) DC 1 2 34 5
ページ13に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 SETTINGS Table A (switch 1 ~ 3) Electronic shutter settings and electronic iris settings 1 AI EI 1/60 1/100 1/500 1/1000 1/2000 1/4000 1/10000 When all of these switches are down, electronic shutter (1/60 sec or auto iris setting) is enabled. The electronic shutter can be set to one 12 3 1 23 1 23 1 23 12 3 1 23 1 23 1 23 of 7 speeds as shown in Table A. (Unit: sec.) Furthermore, when all switches are up, electronic iris setting is enabled. Gain up setting 2 No
ページ14に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 SETTINGS (MULTI mode: 48 sections) Backlight compensation setting 45 This camera has two different backlight compensation functions: Normally backlight compensation switch 6 (MULT) and 7 (CENT) are set to the down (OFF) position. Change the backlight compensation switch settings 6 7 depending on the conditions. • MULT mode: Use this position when applying backlight compensation to the whole of the screen. (CENT mode) • CENT mode: Use this position when applying
ページ15に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 SETTINGS White balance adjustment 6 External sync adjustment (VBS) 7 Normally the switch 8 (WB) is set to the down (ATW: auto white 1 Connect the VBS signal output for the other camera to the VBS IN balance) position and the white balance is adjusted automatically. If a connector at the rear of this camera. manual white balance adjustment is necessary, follow the steps below. 2 If the signals are not synchronized, change the sub-carrier Set the switch 8 (WB) to
ページ16に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 SETTINGS Lens iris adjustment 9 If using a DC type auto-iris lens, you will need to set the LEVEL (VR301) volume when shooting in the conditions described below. VR301 L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast • If shooting simultaneously in a dark room and through a bright window. • If the subject background is extremely bright or dark. • If the brightness of the picture on the monitor is not correct. English 15
ページ17に含まれる内容の要旨
ページ18に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 SPECIFICATIONS Camera: Environmental : Temperature: –10°C ~ +50°C conditions Humidity: less than 90% (no condensation) Scanning system : NTSC standard TV system (525 TV lines, 30 frames/sec.) Power supply : 24 V AC, 60 Hz Power consumption : Approx. 2.8 W (with auto iris lens) Interlace : PLL 2:1 interlace Approx. 2.1 W (without auto iris lens) Image device : 1/3 inch solid state image device CCD Weight : Approx. 310 g (without lens) Picture elements : 811 (H)
ページ19に含まれる内容の要旨
ページ20に含まれる内容の要旨
L53H4/US2 (VCC-5984) GB 2003, 1, 7 Printed on recycled paper SANYO Electric Co., Ltd. 1AC6P1P2624-- Printed in Japan L53H4/US2(0103KPS-CZ)
