ページ1に含まれる内容の要旨
Router
MODEL RF1100/RF1101
MODEL RD1100/RD1101
003648
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
ページ2に含まれる内容の要旨
SPECIFICATIONS Model RF1100 RF1101 RD1100 RD1101 Collet chuck capacity 1/2” and 1/4” No load speed (RPM) 24,000/min. 8,000 - 24,000/min. 24,000/min. 8,000 - 24,000/min. Overall height 223 mm (8-3/4”) Net weight 3.2 kg (7.1 lbs) 3.6 kg (7.9 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA001-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions
ページ3に含まれる内容の要旨
5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded. be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will Tool Use and Care increase t
ページ4に含まれる内容の要旨
24. When servicing a tool, use only identical SERVICE replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury. electric shock or injury. USE PROPER EXTENSION CORD: Use only three-wire extension cords that have three-
ページ5に含まれる内容の要旨
An adapter Fig. “B” and “C” is available for connecting Fig. “A” type plugs to two- prong receptacles. The green-colored rigid ear, lug, etc., extending from the adapter must be con- nected to a permanent ground, such as a properly grounded outlet box. Adapter Grounding Means Cover of Grounded Grounding Outlet Box Blade Fig. A Fig. B Fig. C SPECIFIC SAFETY RULES USB013-3 DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to router safety rules. If
ページ6に含まれる内容の要旨
13. Do not touch the bit immediately after 16. Draw attention to the need to use cutters operation; it may be extremely hot and of the correct shank diameter and suitable could burn your skin. for the speed of the tool. 14. Always lead the power supply cord away 17. Some material contains chemicals which from the tool towards the rear. may be toxic. Take caution to prevent dust inhalation and skin contact. Follow mate- 15. Do not smear the tool base carelessly with rial supplier safety data. thi
ページ7に含まれる内容の要旨
3 4 5 8 FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 003653 Adjusting the depth of cut 1 2 Place the tool on a flat wood surface. Open the lock lever. 3 Turn the motor unit until the bit just touches the flat surface. 1 2 Close the lock lever. 4 Rotate the scale ring until the zero-line is on the index line on the motor unit. One graduation on the scale ring means the 5 cutting edge of the bit is
ページ8に含まれる内容の要旨
003663 For RD1100 and RD1101 1 CAUTION: • Before plugging in the tool, always check to see that the 2 switch trigger actuates properly and returns to the “OFF” position when released. 3 • Switch can be locked in “ON” position for ease of 4 operator comfort during extended use. Apply caution 1. Motor unit cord when locking tool in “ON” position and maintain firm 2. Outlet grasp on tool. 3. Lock button 4. Switch trigger After connecting the motor unit cord to the outlet in the han- dle, move the s
ページ9に含まれる内容の要旨
ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing the bit CAUTION: • Do not tighten the collet chuck without inserting a bit, or the collet chuck will break. • When using bit of bigger than 1-1/4” in diameter, install base plate with center hole diameter 2-1/2”, replacing the original base plate. 003672 First, remove the motor unit from the base as follows. 1 1. Open the lock lever. 2. While holding the
ページ10に含まれる内容の要旨
For equipped with switch-in-handle 003675 For model RD1100 and RD1101 only 1 Connect the motor unit cord to the outlet in the handle. 2 1. Motor unit cord 2. Outlet Set the tool base on the workpiece to be cut without the bit OPERATION making any contact. Then turn the tool on and wait until the bit attains full speed. Move the tool forward over the work- piece surface, keeping the tool base flush and advancing smoothly until the cutting is complete. When doing edge cutting, the workpiece surfac
ページ11に含まれる内容の要旨
003678 Straight guide (optional accessory) The straight guide is effectively used for straight cuts when chamfering or grooving. 003682 To install the straight guide, insert the guide bars into the 1 holes in the tool base. Adjust the distance between the bit and the straight guide. At the desired distance, tighten the 2 hex socket bolts to secure the straight guide in place. When cutting, move the tool with the straight guide flush with the side of the workpiece. 3 1. Hex socket bolts 2. Guide
ページ12に含まれる内容の要旨
003696 Secure the templet to the workpiece. Place the tool on the 6 1 templet and move the tool with the templet guide sliding along the side of the templet. 2 3 4 5 1. Router bit 2. Base 3. Templet 4. Workpiece 5. Templet guide 6. Lock nut MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. 001145 Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit m
ページ13に含まれる内容の要旨
ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. • Straight & groove forming bits • Edge forming bits • Laminate trimming bits • Straight guide • Templet guides •
ページ14に含まれる内容の要旨
Memo 14
ページ15に含まれる内容の要旨
Memo 15
ページ16に含まれる内容の要旨
Memo 16
ページ17に含まれる内容の要旨
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 17 Cut
ページ18に含まれる内容の要旨
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
ページ19に含まれる内容の要旨
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
ページ20に含まれる内容の要旨
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
