ページ1に含まれる内容の要旨
EZ-1
ONE BUTTON REMOTE START SYSTEM
OPERATING INSTRUCTIONS
CONGRATULATIONS on your choice of a Cool Start™ Remote Engine Starter and Keyless Entry with DP
Technology by Crimestopper Security Products Inc. This booklet contains the information necessary for operating
your system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These are features that m
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Operation Cautions & Warnings…….……………..….…………………………………….…………….….…………2 Using the Remote Transmitter………………………………………………………………………….………....…….3 Status LED……………………………………………………………………………………………….……….……….4 Remote Engine Control…………….…..……………………………………………………………….…….……….4-7 Turbo Timer Mode……………………………….……………………………………...……………….…………..…8-9 Convenience and Safety Features……………………………….………………………………….…...……..…10-11 Valet Service Mode.…………………………………….………………...…………………………………….………11 Transmitt
ページ3に含まれる内容の要旨
USING THE REMOTE TRANSMITTER LED START BUTTON REMOTE START BUTTON PRESS SELECTION (Option # 6): The transmitter supplied with this system is a single button remote control. To eliminate the possibility of accidentally starting the vehicle, there are (3) options for button press selection. This option will allow you to change whether the Remote Starter is activated by a: 1. Double Button - ½ second presses. 2. *Single ½ second press (Default). 3. Press and Hold 2 seconds.
ページ4に含まれる内容の要旨
STATUS LED VEHICLE STATUS LED : (Install optional) The optional LED will remain solid when the system is in Valet Service mode. The remote start function WILL NOT operate when in Valet Mode. See page # 11. REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - SUCCESSFUL START: 1) Press the remote start button for at least 1/2 second (*default). Parking lights flash once, return solid, and the Ignition/Acc circuits turn on. 2) After a few seconds the Starter Motor engages. The parki
ページ5に含まれる内容の要旨
REMOTE ENGINE CONTROL REMOTE ENGINE STARTING - UNSUCCESSFUL START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then nd rd attempts to restart the engine a 2 and 3 time. For hard starting engines, the unit will allow a starter crank time of up to13 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 13 seconds to help prevent damage to the starter from over cranking. nd rd 1) If en
ページ6に含まれる内容の要旨
REMOTE ENGINE CONTROL IDLE DOWN MODE: This mode allows the unit to take over operation of the parked vehicle while the ignition key is removed and you exit the vehicle. The vehicle is put into a remote running condition before you exit and it will remain running for the programmed run time or until you come back. Examples: • You pull up to a convenience store for a quick stop, "Idle Down" mode keeps engine running when you exit the vehicle, (with keys in hand) remote lock doors or ar
ページ7に含まれる内容の要旨
REMOTE ENGINE CONTROL INFINITY RUN MODE This mode can only be activated with "Idle Down" procedure. The Infinity Run mode allows the vehicle engine to remain running INDEFINITELY after the programmed run time elapses. This mode will allow the vehicle to be left running and unattended without the ignition key in the switch preventing the vehicle from being stolen. This mode can be beneficial to law enforcement or commercial trucks that need to remain running unattended for long periods
ページ8に含まれる内容の要旨
TURBO TIMER MODE (OPTION #22) The optional Turbo Timer mode allows the CoolStart system to keep a Turbo or Turbo Diesel vehicle running for 1 to 5 minutes [selectively] after you remove the key and exit the vehicle. This is handy for turbo cool-down without the need for expensive turbo timers. This mode requires the use of an extra part called a momentary switch/button that is not included with the kit. There are (3) modes of operation for the Turbo Timer Mode 1. Brake Pedal Set Mo
ページ9に含まれる内容の要旨
SETTING THE TURBO TIMER RUN TIME PRESS TURBO RELEASE PRESS TIMER BUTTON RUNNING BRAKE AND HOLD 1-5 TIMES BRAKE LIGHTS REMOVE KEY FLASH 1-5X REMAIN RUNNING 1-5 MIN. EXIT VEH. 9
ページ10に含まれる内容の要旨
CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (POWER DOOR LOCK CONTROL, Optional) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) via remote control for safety and convenience. Note: This feature may require extra labor and/or parts to install. Press the Lock or Unlock transmitter button as you leave or come near the vehicle. Parking lights will flash once for lock and twice for unlock. If vehicle is running by the remote sta
ページ11に含まれる内容の要旨
CONVENIENCE AND SAFETY FEATURES VALET MODE (Requires Installation of Valet Switch) Before servicing your vehicle or handing the keys over to a Valet we recommend putting the unit into Valet Mode. The remote start function WILL NOT operate when in Valet Mode. To enter Valet mode, turn the key to the ON position, press and hold Program/Valet switch for 5-6 seconds. The LED will turn on solid when the system is in Valet Mode. To exit Valet Mode, perform this procedure again. The keyless
ページ12に含まれる内容の要旨
TRANSMITTER PROGRAMMING Note: All transmitter codes must be learned at time of programming!! The RS-1 learns up to 4 different transmitter codes. 1. Turn key to the ON position. (Pink wire must be connected.) 2. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 3. Press button #1 of the transmitter to be coded. You should get 2 light flashes indicating the unit is waiting for a nd rd 2 code, then press button #1 of a second t
ページ13に含まれる内容の要旨
NO FACTORY KEYLESS ENTRY AFTER REMOTE START Most new cars Do Not allow the factory Remote Keyless Entry to function with the Ignition ON. This means you can’t use the factory remote to lock or unlock the doors. After remote start you have to use the keys to unlock the door. Also, many new vehicles unlock the doors when disarming the factory alarm. This leaves the doors unlocked while Remote Started. To resolve this problem, have your installer connect the door locks to the Remote Start K
ページ14に含まれる内容の要旨
BATTERY REPLACEMENT To replace the battery: Simply remove the screw on back of the transmitter and slide the case apart as shown. Remove the two CR-2016 Lithium batteries and replace. Slide case back together and tighten screw. Back Cover LITHIUM CR 2016 Screw Slide apart 14
ページ15に含まれる内容の要旨
2-Way DATA PORT Some vehicles require a Databus Module to Bypass the factory Immobilizer and operate the keyless entry Databus modules are used to communicate with the vehicles computer at the OBD2 Data connector or Canbus wires. This reduces installation error. Crimestopper Systems with DP Series have a direct Data Port Plug-In for the Databus bypass module. This eliminates conventional wiring between the Alarm/Remote Starter and the bypass interface module. Features Include • Tran
ページ16に含まれる内容の要旨
www.crimestopper.com ONLINE TECHNICAL SUPPORT email@crimestopper.com www.crimestopper.com Phone (800) 998-6880 FAX (805) 581-9500 © 2008 Crimestopper Security Products 16