ページ1に含まれる内容の要旨
Model PRO-9642
Owner's Manual
3 Button Remote Security System
FEATURES:
2 Three Button Programmable RF Transmitters
Three Channel Receiver (capable of accepting 4 transmitters)
Anti-scan Technology
Remote Panic in all modes
Protected Valet
7 Function LED - Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming
Intrusion Alert with Memory
Audible Arm / Disarm / Defective Zone / Tamper Confirmation
Instant Siren Activation
Low Current Horn Output
True Last Door Arming (ha
ページ2に含まれる内容の要旨
ARMING THE SYSTEM - ACTIVE 1. Turn off the engine, exit the vehicle and close all doors, hood lid, and trunk lid. 2. Press and release the Arm / Lock button on the keychain transmitter. Red dash mounted LED begins to flash slowly. Parking Lights flash one time. Siren and / or Horn sounds one chirp. If the siren sounds 3 chirps, then you have left a door, trunk, or the hood lid ajar. Simply close the opened entry point to provide full protection. If the siren/horn did not sound when arming
ページ3に含まれる内容の要旨
protected entry points. If the thief left a door opened, the alarm will sound for six 30 second cycles, remain armed and ignore that triggered zone. Whenever the system is armed, the red dash mounted LED indicator will slowly flash. This serves as a visual deterrent to the potential thief. The LED is a very low current bulb and will not cause the vehicle’s battery to drain, even when left unattended for extended periods. Whenever the system is triggered, the vehicle’s parking lights will fla
ページ4に含まれる内容の要旨
Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered. Siren/Horn does not sound. If the siren and or horn sounds 4 chirps, then the alarm was triggered in your absence. Before turning the key on, examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered. Doors Unlock - Optional WHILE
ページ5に含まれる内容の要旨
3. To return to normal operation, press and release the pushbutton switch any time the ignition is on. NOTE : Always remember to return the system to the NON VALET mode after servicing to ensure that the vehicle remains protected at all times. MANUALLY OVERRIDING YOUR SYSTEM: USING THE VALET SWITCH MANUAL OVERRIDE Your Security System can be disarmed without the use of the keychain transmitter. This is nec- essary, since you will need the ability to operate your vehicle if the transmitter is los
ページ6に含まれる内容の要旨
NOTE: If 15 seconds of inactivity expire or if the ignition switch is turned off for more than 5 seconds during any of the above steps, the unit will revert back to the last success- fully stored code. Custom Code Programming Example: To Change the code from the factory pre-assigned code of 11 to “52” you would do the following: 1. Disarm the system by use of the transmitter, or by use of the emergency override se- quence. 2. Turn the ignition switch to the on position. 3. Within 10 seconds, pre
ページ7に含まれる内容の要旨
ELIMINATING THE NORMAL ARM / DISARM CHIRPS As explained earlier in the manual, you can eliminate the chirps selectively any time you arm or disarm the system simply by holding the ARM / DISARM button for two seconds. If you find the normal arming and disarming chirps annoying, they can be turned off permanently, eliminating the need to hold the ARM / DISARM button for two seconds. To do this, 1. With the valet switch in the off position, turn the ignition key on then off. 2. Within 10 seconds,
ページ8に含まれる内容の要旨
PRO-9642 SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN CHIRP INDICATORS 1 CHIRP * = ARM 2 CHIRPS * = DISARM 3 CHIRPS = ARM / DOOR OPENED 4 CHIRPS = DISARM / INTRUSION * These chirps are optional, and can be de - activated. PARKING LAMPS 1 FLASH = ARM 2 FLASHES = DISARM 3 FLASHES = DISARM / INTR
