ページ1に含まれる内容の要旨
Model AX-200
Owner’s Manual
3 Button Remote Security System with
Stage Shock Sensor & Starter Disable
FEATURES :
2 Three Button Code Hopping RF Transmitters
Three Channel Code Learning Receiver (capable of accepting 4 transmitters)
Selectable Manual Override Mode
Remote Panic in all modes
Protected Valet
7 Function LED -(Light Emitting Diode) - Arm / Disarm / Zone1, 2, 3 / Valet / Arming
Intrusion Alert with Memory
Audible Arm / Disarm / Defective Zone / Tamper Confirmation
I
ページ2に含まれる内容の要旨
NOTE: Your system has the option of using a siren, the vehicle horn, or both for the sounding device. Where the siren is referenced below, the horn or both may in fact chirp, or beep. ARMING THE SYSTEM - ACTIVE 1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid. 2. Press and release the ARM button on the keychain transmitter. The dash mounted LED begins to flash slowly. Parking Lights flash one time. Siren and or Horn sounds one chirp. If the siren/horn
ページ3に含まれる内容の要旨
PROTECTION WHILE THE SYSTEM IS ARMED Opening any protected door, hood, or trunk lid will cause the alarm to immediately sound. The alarm will continue to sound for 30 seconds, then stop and continue to monitor all protected entry points. If the thief left a door opened, the alarm will sound for six 30 second cycles, remain armed and ignore that triggered zone. Whenever the system is armed, the dash mounted LED indicator will slowly flash. This serves as a visual deterrent to the potential t
ページ4に含まれる内容の要旨
button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. 1. As you approach the vehicle, press and hold the ARM / DISARM button on the keychain transmitter for 2 seconds. The dash mounted LED turns off. If passive arming was selected during the installation, then the LED will start flashing rapidly, indicating that the system is re arming automatically. Open any door to suspend the automatic arming. Parking Lights flash
ページ5に含まれる内容の要旨
valet mode, all alarm functions are bypassed, however the remote panic feature and remote door locks will remain operational. To use the valet mode, the system must first be disarmed either by using your keychain transmitter, or by operating the manual override sequence. 1. From the disarmed condition, turn the ignition key to the on position. 2. Press and hold the valet pushbutton switch until the dash mounted LED, turns on. The LED will remain on as long as the system is in valet mode. 3. To
ページ6に含まれる内容の要旨
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5 seconds during any of the above steps, the unit will revert back to the last successfully stored code. Custom Code Programming Example: To Change the code from the factory preassigned code of 11 to “52” you would do the following: 1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. 2. Turn the ignition switch to the on position. 3. Within 10 seconds, press a
ページ7に含まれる内容の要旨
1. Turn the ignition key on then off. 2. Within 10 seconds, press and release the valet push button switch three times. 3. If the chirps were on before you started, then you will hear 2 chirps indicating they have been turned off. If the chirps were off before you started, then you will hear one chirp indicating they have been turned on. NOTE: Whenever the chirps are by - passed, the 4 chirp intrusion indicator and 3 chirp defective zone indicator will always operate. Since these are important w
ページ8に含まれる内容の要旨
AX-200 SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN CHIRP INDICATORS 1 CHIRP * = ARM 2 CHIRPS * = DISARM 3 CHIRPS = ARM / DOOR OPENED 4 CHIRPS = DISARM / INTRUSION * These chirps are optional, and can be deactivated. PARKING LAMPS 1 FLASH = ARM 2 FLASHES = DISARM 3 FLASHES = DISARM / INTRUSION
