ページ1に含まれる内容の要旨
Installing the
™
iPower 70
Room Camera
ページ2に含まれる内容の要旨
Copyright © 2000-2002: Polycom, Inc. Polycom, Inc., 4750 Willow Road, Pleasanton, CA 94588 www.polycom.com Polycom and the Polycom logo are registered trademarks of Polycom, Inc. Concorde, Venue, and WorldCart are trademarks of PictureTel Corporation. Velcro is a registered trademark of Velcro USA, Inc. All other company and product names are the trademarks or registered trademarks of their respective owners. The information contained in this document is subject to change without notice. Polycom
ページ3に含まれる内容の要旨
Installing the iPower 70 Room Camera ® This booklet describes how to install the iPower 70 room camera. About this The iPower 70 is a pan-tilt-zoom (PTZ) camera that is used with a Booklet iPower collaboration system as a main or an auxiliary camera. This booklet contains information on: ❑ Before you install (page 4) ❑ Unpacking the box (page 5) ❑ Important note (page 6) ❑ Attaching the camera to a monitor (page 7) ❑ Connecting the camera cable to the collaboration system (page 8) ❑ Connecti
ページ4に含まれる内容の要旨
INSTALLING THE IPOWER 70 ROOM CAMERA Before Installing Warning Before you begin this procedure, make sure you turn off your collaboration system’s power switch. To install this camera, you will need: 8 ❑ The 8-pin camera cable a (labeled with the icon on both cable collars) that came with your collaboration system, the WorldCart™, or the Premier Cart. (A camera cable is not supplied with this camera.) ❑ One of the following systems: iPower 900 system, software version 1.0 or higher Conc
ページ5に含まれる内容の要旨
Unpacking the Box To remove the camera from the box: Unpacking the Box 1. With two hands, grasp the outside edges of the packing material and gently lift the unit from the box. 2. Carefully remove the camera from the packing material and place it on a flat surface. Caution When lifting the iPower 70 camera, always lift the unit by its base. Never lift the camera by its head. Note: Before you continue with the installation of the camera, please read the next section, “Important Note About Movi
ページ6に含まれる内容の要旨
INSTALLING THE IPOWER 70 ROOM CAMERA The iPower 70 camera is designed to be controlled (moved) from the Important Note collaboration system wireless keypad, the keyboard, or the remote About Moving the control. Be sure that your system is turned on before you move the Camera camera. You should not manually move the camera from side to side (pan) or up and down (tilt). If you manually move the iPower 70 camera head, you may experience unexpected camera pointing behavior when you use camera
ページ7に含まれる内容の要旨
Attaching the Camera to a Monitor Note: If you are installing a second monitor for a iPower 900 Attaching the system, be sure to install the iPower 70 camera on the Camera to a NTSC or PAL monitor and not on the VGA monitor. If Monitor you are installing a second monitor for a Concorde4500 or Venue2000 system, be sure to install the iPower 70 camera on the main monitor and not on the graphics monitor. To attach the camera to the monitor: 1. Clean the top of the monitor using a dry clot
ページ8に含まれる内容の要旨
INSTALLING THE IPOWER 70 ROOM CAMERA Connecting the Camera Cable Caution Whenever you plug a cable into this camera, hold the camera by its base, not by the camera head. To connect the camera cable: a 8 1. Plug the 8-pin camera cable (labeled with the icon on both cable collars) into the 8-pin camera connector b on the back of the camera. 2. Locate the desired camera connector (labeled with the 8 icon) on the back of the collaboration system computer box or electronics A module c . (Choose for
ページ9に含まれる内容の要旨
Connecting an Additional Power Cable Although the camera cable provides power to the iPower 70 camera, Connecting an if you are using a camera cable longer than 32.8 feet (10 meters), you Additional Power must use an additional power cable for the camera. Cable To connect an additional power cable: 1. Plug the additional power cable into the power connector on the a back of the camera . 2. Plug the other end of this cable into an appropriate power source. If you are in the process of installin
ページ10に含まれる内容の要旨
INSTALLING THE IPOWER 70 ROOM CAMERA For support or service, please contact your Polycom service Service and provider or call Polycom Technical Support. You can find phone Support numbers for Technical Support in your area at the Polycom web site, www.polycom.com. Specifications Physical Specifications Dimensions: Length: 7.2 in. (18.3 cm) Width: 7 in. (17.8 cm) Height: 5.4 in. (13.7 cm ) Weight: 3.5 lb. (1.6 kg) Operating and Nonoperating Environments Temperature: Operating: 32° to 104° F (0
