ページ1に含まれる内容の要旨
PROFESSIONAL SERIES MODELS
PL30WC4IEC
PL36WC4IEC
GALLERY SERIES MODELS
GL30WC4IES
GL36WC4IES
GL30WC4IEB
Patent No.: US D450, 829 S
GL36WC4IEB
READ AND SAVE THESE INSTRUCTIONS
! ! ! !
FOR DOMESTIC COOKING ONLY
!
WARNING CAUTION
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO 1. For general ventilating use only. Do not use to exhaust hazardous or
PERSONS, OBSERVE THE FOLLOWING: explosive materials and vapors.
1. Use this unit only in the manner intended by the manufacturer. If you 2. T
ページ2に含まれる内容の要旨
PREPARE HOOD LOCATION PREPARE HOOD LOCATION ROOF CAP 3¼" X 10" or 7” ROUND 7" ROUND DUCT (For vertical VERTICAL DUCTING discharge) SOFFIT HOUSE WIRING CABINET (Top or Back of hood) WALL CAP HOOD HOOD HOOD 24" - 30" ABOVE 3¼" X 10" DUCT COOKING SURFACE (For horizontal discharge) 3 Run house wiring between service panel and hood 1 Determine whether hood will discharge vertically (3¼” x 10” location. or 7” Round), or horizontally (3¼” x 10” only). For vertical or horizontal discharge, run ductwor
ページ3に含まれる内容の要旨
➠ ➠ ➠ PREPARE THE HOOD PREPARE THE HOOD 7 Remove Air 3 Remove ® Teflon -coated Chute - held in place with one bottom cover AIR CHUTE from hood. Set (1) screw. cover and mounting screws NOTE: Be aside. careful not to disconnect any ® Teflon is a registered wires. trademark of DuPont. ® TEFLON -COATED BOTTOM COVER (Held in place with 2 screws) 4 Remove Damper/Duct Connector from inside 8 Remove Baffle the hood. Set from air chute. connector aside - with mounting screws and parts bag. DAMPER/ DUCT
ページ4に含まれる内容の要旨
➙ PREPARE THE HOOD PREPARE THE HOOD TAPE TOP/BACK TOP RECTANGULAR UP TO 1” EDGE DUCT KNOCKOUT SEMI-CIRCULAR SIDE-TO-SIDE (Remove for 3¼” x 10” DUCT KNOCKOUT ADJUSTMENT Vertical & for 7” Round (Remove for 7” Round Discharge) Discharge) DAMPER/ PIVOT DUCT CONNECTOR (Vertical discharge position shown) REAR RECTANGULAR DUCT KNOCKOUT 13 3¼” x 10” Ducted Discharge Only: Remove Tape from (Remove for 3¼” x 10” damper flap and attach Damper/Duct Connector over Horizontal Discharge) knockout opening with
ページ5に含まれる内容の要旨
CONNECT WIRING INSTALL HOOD WARNING: To reduce the risk of electric shock, make sure power is switched off at the service panel. Lock or tag service panel to prevent power from being switched on accidentally. HOUSE WIRING (120 VAC) KEYHOLE (4) MOUNTING SCREW (4) 1 Hang hood from (4) Mounting Screws. Slide hood towards wall until mounting screws are engaged in narrow end of (4) CARDBOARD Keyholes. Tighten mounting screws securely. A long (Use to protect screwdriver works best. cooktop) 2 Replace
ページ6に含まれる内容の要旨
NON-DUCTED FILTERS OPERATION If hood is to be installed Non-Ducted: Purchase a set of (2) Non-Ducted Filters from your local distributor or retailer and attach them to the aluminum mesh filters. Fan and Lights: 3 push button switches for each. Push any button to select one of 3 fan speeds or one of 3 light levels. Push the NOTE: For models that are installed in the non-ducted mode, the same button to turn fan or light off. Press another button to change most effective operation is achieved at sp
ページ7に含まれる内容の要旨
SERVICE PARTS 1 3 KEY NO. DESCRIPTION 3 1 7” Round Duct Plate (includes hardware) 3 2 Damper/Duct Connector (includes hardware) 4 3 Screw, #8-18 x ¼ Hex* (2 in package) 2 4 Motor Capacitor (includes wire nuts & hardware) 12 3 5 Isolation Transformer 5 6 Nameplate 6 9 24 7 Control Panel (includes Key No. 6 & hardware) 8 Screw for Plastic, #6 x ½ Flat Hd. (3 in package) 8 9 Screw, #8-18 x 3/8 (2 in package) 10 Ground Screw 11 Scroll Cover, Outlet (includes hardware) 7 12 Scroll Cover, Front (incl
ページ8に含まれる内容の要旨
Major Appliance Warranty Information Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. Exclusions This warranty does not cover the following: 1. Products with original serial numbers that have been remo
