ページ1に含まれる内容の要旨
INTERACTIVE PEN DISPLAY
Interactive Pen Display
INSTALLATION GUIDE AND USER’S MANUAL
INSTALLATION GUIDE
AND USER’S MANUAL
WACOM Co., Ltd.
UE-0248 (A) 0X1075229 (A)
ページ2に含まれる内容の要旨
Wacom Technology Corporation 1311 S.E. Cardinal Court Vancouver, WA 98683 U.S.A. Telephone General: ++1-360-896-9833 Fax: ++1-360-896-9724 WACOM Europe GmbH Europark Fichtenhain A9 47807 Krefeld Germany Telephone General: ++49-(0)2151-3614-0 Fax: ++49-(0)2151-3614-111 WACOM Co., Ltd. 2-510-1 Toyonodai Otone-Machi, Kitasaitama-gun Saitama, 349-1148 Japan Telephone General: ++81-(0)480-78-1213 Fax: ++81-(0)480-78-1217 As an Energy Star© partner, Wacom Company Ltd. has determined that this product
ページ3に含まれる内容の要旨
Interactive Pen Display INSTALLATION GUIDE AND USER’S MANUAL 1
ページ4に含まれる内容の要旨
Introduction and Overview ® ™ The Wacom Cintiq 15X Interactive Pen Display combines an LCD display with a Wacom tablet. This gives you a direct point-and-draw-on-screen interface that can be used with a Personal Com- ® ™ ® puter (PC), Macintosh computer, or SGI or Sun workstation. Cintiq’s basic components include a Wacom tablet internally mounted behind a 15.0" diagonal TFT color LCD monitor, and Wacom’s Grip Pen. Your Cintiq Interactive Pen Display offers a number of significant advantages ov
ページ5に含まれる内容の要旨
Precautions on Use and Handling Be sure to follow all instructions, cautions, and warnings found within this manual. Failure to do so could void your warranty, in which case Wacom shall have no responsibility to repair or replace the product. P H Y S I C A L L O C A T I O N WARNING n Do not use the Cintiq Interactive Pen Display in a facility control system that requires extremely high reliability; it may cause other electronic devices to malfunc- tion, or other devices may cause the Interact
ページ6に含まれる内容の要旨
H A N D L I N G WARNING n High Voltage. Do not open or disassemble the Cintiq Interactive Pen Display. There is a risk of electrical shock when the casing is open. This will also void your warranty and Wacom shall have no responsibility to repair or replace the product. WARNING n If the LCD screen has been damaged, DO NOT touch any liquid that may be leaking from it; this liquid is an irritant. In case of contact with skin, eyes, or mouth, rinse immediately with running water for at least 15
ページ7に含まれる内容の要旨
Radio and Television Interference (U.S.A.) The equipment described in this manual generates, uses, and can radiate radio-frequency energy. If it is not installed and used properly—that is, in strict accordance with Wacom instructions—it may cause interference with radio and television reception. F E D E R A L C O M M U N I C A T I O N S C O M M I S S I O N ( F C C ) N O T I C E This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Par
ページ8に含まれる内容の要旨
CE Declaration (Europe) The equipment described in this manual generates, uses, and can radiate radio-frequency energy. If it is not installed and used properly—that is, in strict accordance with Wacom instructions—it may cause interference with radio and television reception. R A D I O A N D T E L E V I S I O N I N T E R F E R E N C E The Cintiq Interactive Pen Display has been tested and found to comply to the following harmo- nized European Norms: n EN 55024 (electromagnetic immunity) n
ページ9に含まれる内容の要旨
Table of Contents CHECKING PACKED COMPONENTS 9 INTERACTIVE PEN DISPLAY COMPONENTS 10 n Front View n Rear View INSTALLATION 12 n System Requirements n Step 1: LCD Display Installation n Step 2: Tablet Installation USING THE GRIP PEN 22 n Working with the Grip Pen (UP-911E) n Using a Pen WORKING WITH CINTIQ 24 CUSTOMIZING CINTIQ 25 n Customizing the Grip Pen n Adjusting the LCD Display CARING FOR CINTIQ 33 n Cleaning n Replacing the Pen Tip TROUBLESHOOTING 34 n Testing Cintiq n Testing the Tablet
ページ10に含まれる内容の要旨
8
ページ11に含まれる内容の要旨
Checking Packed Components In your package you will find the following items: Power Supply (LE-9702B-01A) and Cintiq Interactive Pen Display, Main Unit Power Cable Grip Pen and Pen Stand UP-911E-01A and PST-A026-04) *1 USB Cable (STJ-A205) Installation Guide and *1 Serial Cable, RS-232C (STJ-A204) and User’s Manual (This manual.) Wacom Tablet CD (Contains the driver software.) *1, 2 DVI-to-VGA Cable (STJ-A207) *1, 2 and DVI-to-DVI Cable (STJ-A206) Notes: Images are not shown to scale. Some pack
ページ12に含まれる内容の要旨
Interactive Pen Display Components F R O N T V I E W The LCD display and tablet sensor function as an integrated input and output device. The LCD display supports resolutions up to 1024 x 768 pixels at 16,777,216 colors. The tablet sensor reports pen coordinates, pressure, switch, and eraser information. On Screen Display Power LED (OSD) Controls Lights green when power has been These controls enable supplied to both Cintiq and the computer you to adjust a variety and a video signal is prese
ページ13に含まれる内容の要旨
R E A R V I E W Stand Adjustment Lever Pull this lever to adjust the stand. Release the lever to lock the stand in place. Digital/Analog (DVI/VGA) Switch Use this switch to correctly set Cintiq for the video connection you will be using. Connector Panel Cover To remove the cover, slide it to the right. Stand The stand can be used to adjust the tilt angle of the unit from a low position CAUTION Be careful to avoid (18° from horizontal) to a catching your finger in high position (73° from the ga
ページ14に含まれる内容の要旨
Installation S Y S T E M R E Q U I R E M E N T S Before installing Cintiq, make sure that your computer meets the following system requirements: n Macintosh. OS 8.6, 9, or 10.1 and higher. DVI or VGA video connector, available USB port, and CD-ROM drive. ADC connectors require an ADC to DVI adaptor (not included). n PC. Windows 95, 98, Me, NT 4.0 (SP-3), 2000, or XP. DVI or VGA video connector, available USB or serial port, and CD-ROM drive. (Windows 95 and NT 4.0 (SP-3) do not support U
ページ15に含まれる内容の要旨
S T E P 1 : L C D D I S P L A Y I N S T A L L A T I O N Cintiq can be used alone or with another display, such as a CRT monitor or LCD projector. To use Cintiq with another display, you will need two video cards or a video card with dual output. Depending on the capabilities of your video card and operating system, you may be able to set up Cintiq as a mirrored, extended, or independent display. Refer to your video card documentation for more information on its capabilities. In the first
ページ16に含まれる内容の要旨
LCD Display Cabling Diagram Cintiq, rear view C DC Input Analog A Digital Digital/Analog (DVI/VGA) switch DVI to DVI cable Or... VGA to DVI cable DVI-I connector Video card DVI or VGA Do not attach the USB or serial data B cable until instructed to do so. Rear panel of your computer Power Supply D To AC Outlet CAUTION Do not use any cable that did not come with Cintiq; use of an improper cable may damage the unit. Make sure that you correctly set the Cintiq Digital/Analog (DVI/VGA) switch fo
ページ17に含まれる内容の要旨
n Turn on Cintiq. The power LED will light. n Next, turn on your computer. Windows 98 and Me: The New Hardware Wizard will display. Insert the Wacom Tablet CD and follow the prompts selecting the default options. If prompted for the location of the files, be sure to check the box for the CD-ROM drive. Windows 2000 and XP: Cintiq will automatically install as a Default Monitor. If you want Cintiq to be identified as a Cintiq display and if you want to install the color calibration profile for
ページ18に含まれる内容の要旨
n The maximum resolution of Cintiq is 1024 x 768, True Color (24 bit). As necessary, configure the display control panel settings for the proper size and color resolution. The number of colors is constrained by the capabilities of your video card. Refer to the video card manufacturer’s docu- mentation for details. For Windows, if you are using Cintiq as a secondary display, you may first need to enable Cintiq in your Display Properties control panel. n After the display portion of Cintiq is w
ページ19に含まれる内容の要旨
Tablet Cabling Diagram Cintiq, rear view Cable guides F E To USB port Or... To serial port Connect either the USB or serial cable; do not connect both cables. Wacom recommends using the USB connec- tion, if available. Rear panel of your computer CAUTION Do not use any cable that did not come with Cintiq; use of an improper cable may damage the unit. Do not connect or disconnect the video or power cables while Cintiq or your computer are turned on – this can damage the LCD display or computer vid
ページ20に含まれる内容の要旨
Tablet Software Install for Macintosh To install the tablet software: n First turn on Cintiq, then turn on your computer and allow the operating system to fully load. Cintiq will automatically register as a USB device. n Disable any virus protection programs and close all open applications before installing the software. n Insert the Wacom Tablet CD into your computer’s CD-ROM drive. The Cintiq menu should automatically display. If the menu does not display (or if you are running OS X), double
