ページ1に含まれる内容の要旨
Installation and Assembly Manual:
PRS Series Projector Mount
Models: PRS-1, PRS-1S, PRS-1W
This product is intended for use with UL
Listed products and must be installed by a
U
C ©L US
qualifi ed professional installer.
Features:
TM
• ImageLock alignment prevents picture sag or drift
Maximum UL Load Capacity:
• Exclusive aluminum track quick release
25 lb (11 kg)
ISSUED: 08-15-07 SHEET #: 055-9188-6 06-25-10
1 of 13
Visit the Peerless Web Site at www.peerlessmounts.com For customer care ca
ページ2に含まれる内容の要旨
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings con- tained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112. • This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction,
ページ3に含まれる内容の要旨
Before you start check the parts list to insure all of the parts shown are included. Parts List PRS-1 PRS-1S PRS-1W Description Qty. Part # Part # Part # A projector mount assembly 1 055-1963 055-4963 055-2963 B 4 mm security allen wrench 1 560-9646 560-9646 560-9646 #10-32 x 3/8" serrated washer head socket pin screw 2 520-1151 520-2151 520-2151 C D #10-32 x 1/4" socket pin screw 1 520-1196 520-2196 520-2196 E flat washer 2 540-1078 540-1078 540-1078 F #14 x 2.5 phillips hex head wood screw 2
ページ4に含まれる内容の要旨
Installation to Extension Column / Ceiling Plate NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to 1 ceiling. Screw projector mount assembly (A) onto extension column as shown in fi gure 1.1. Tighten swivel stop screw against extension column, fl ush mount tube or reducer using 4 mm security t-wrench (B) as shown in fi gure 1.2. NOTE: Swivel stop screw is used to jam against threads of extension column, fl ush mount tube or reducer
ページ5に含まれる内容の要旨
Installation To Wood Joist Ceilings WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that projector mount assembly is fi rmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud. The
ページ6に含まれる内容の要旨
Installation to Concrete Ceilings WARNING • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard- ware and components. Place projector mount assembly (A) on ceiling as a 3 template and mark the center of the two mounting holes. Drill two 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach projector mount assembly (A) u
ページ7に含まれる内容の要旨
Installation to Threaded Rod (Not evaluated by UL - Professional installation only) Thread two 3/8-16 hex thin nylon-insert locknuts (not included) on two 3/8-16 threaded rods (not included) to the 4 desired height of projector mount assembly. Attach projector mount assembly (A) to the two 3/8-16 threaded rods using two 3/8-16 hex thin nylon-insert locknuts as shown in fi gure 4.1 or fi gure 4.2. 3/8 -16 THREADED ROD (NOT INCLUDED) 3/8 -16 THREADED ROD (NOT INCLUDED) 3/8 -16 HEX THIN NYLON-
ページ8に含まれる内容の要旨
Attaching Adapter Plate to Projector CAUTION H • It is the responsibility of the installer to ensure that SHOULDER the projector is properly ventilated. NOTCH INDICATES FRONT OF PROJECTOR DEDICATED Installing Dedicated PAP Series Adapter ADAPTER PLATE 5 Plate (sold separately) (SOLD SEPARATELY) NOTE: The projector dedicated adapter plate you are installing may differ in appearance from the sample illustrated in fi gure 5.1. Align shoulder of connection block (I) opposite notch of adapter pl
ページ9に含まれる内容の要旨
Attaching Adapter Plate to Projector (continued) WARNING • Always use an assistant or mechanical lifting equipment to safely lift and position the projector. Slide connection block with projector into projector mount assembly (A) as shown. Push in and tighten captive 6 screw to secure projector to projector mount assembly (A). H FRONT OF MOUNT A CAPTIVE SCREW IMPORTANT: For security installations, insert one #10-32 x 1/4" socket pin screw (E) through projector mount as- 7 sembly (A) and into
ページ10に含まれる内容の要旨
Cable Management fi g. 8.1 To make an opening to route cables through projector CABLES WITH COMBINATION NOTE: INNER DIAMETER OF 8 mount assembly, adjust projector mount assembly to full OF VGA CONNECTOR EXTENSION COLUMN MAY NOT upward tilt position by turning knob for tilt adjustment AND RCA PLUGS ALLOW PASSAGE FOR ALL as shown in fi gure 8.2. Left or right roll position can be CONNECTOR TYPES. BEND WIRES OF RCA adjusted if more space is required. PLUGS IN OPPOSITE DIRECTION NOTE: Be cert
ページ11に含まれる内容の要旨
Projector Alignment To adjust yaw (swivel) for wood stud, concrete ceiling, and threaded rod mounting applications: Loosen 9 wood screws (F), or locknuts for threaded rods, until projector mount can be rotated. Rotate mount to desired posi- tion and retighten screws or locknuts. To adjust yaw (swivel) for extension column applications: Loosen screw on projector mount assembly (A) indi- cated below until projector mount can be rotated. Rotate mount to desired position and retighten screw. To
ページ12に含まれる内容の要旨
PRS Series Projector Mount Accessories Ceiling Plates ® Truss Ceiling Adapter Escutcheon Ring Unistrut Adapter MODEL: ACC 557* MODEL: ACC 640 MODEL: ACC 550 MAX LOAD: 250 lbs. (113.4 kg.) MAX LOAD: 250 lbs. (113.4 kg.) • Covers hole where extension COLOR: Black COLOR: Black column passes through ceiling • Hinged ring wraps around extension column • Attaches to a square, round, • Designed for use with • Included with CMJ 500 rectangular, or I-Beam truss up to 3" in 1 5/8" x 1 5/8" 12 gauge Uni
ページ13に含まれる内容の要旨
PRS Series Projector Mount Accessories Cord Management • Includes, four, 2' sections Cord Wrap • Designed to externally route cords along the MODELS: ACC 852(W)(S)* outside of an 1/2" extension column • Sections can be stacked to create longer lengths COLOR: Black, White, or Silver or cut to desired length Extension Columns Adjustable Length 1 1/2" Fixed Length 1 1/2" Extension Columns Extension Columns COLOR: Black COLOR: Black MODEL Drop Length Ship Weight MODEL Drop Length Ship Weight ADJ
