ページ1に含まれる内容の要旨
Installation and Assembly:
Universal Projector Ceiling Mount
This product is UL Listed. It must be
Model: ELPMBPJF
installed by a qualified professional
installer.
Distributed by:
Epson America, Inc.
Maximum UL Load Capacity: 50 lb (22.7 kg)
3840 Kilroy Airport Way
Long Beach, CA 90806
www.epson.com
Manufactured by Peerless Industries, Inc.
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ページ2に含まれる内容の要旨
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call Peerless customer care at 1-800-729-0307. • This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands
ページ3に含まれる内容の要旨
Before you start check the parts list to ensure all of the parts shown are included. Parts List Description Qty. Part Number A projector mount 1 055-0016 B 4 mm security allen wrench 1 560-9646 C M5 x .8 x 10 mm socket pin type F screw 1 520-2031 D #10-32 x 3/8" spade thumb screw 1 560-2107 E #10-32 x 3/8" serrated washer head socket pin screw 1 520-2151 F #14 x 2.5" phillips hex head wood screw 2 5S1-015-C04 G ceiling plate 1 580-4042 H .25" ID x .56" OD x .26 spacer 2 590-2071 I extension col
ページ4に含まれる内容の要旨
Installation to Extension Column Screw extension column (sold separately) EXTENSION 1 to ceiling plate (G). Align the notch with COLUMN one of the four holes in the ceiling (ELPMBC01, UL Listed plate (G) and secure extension column G EXT or ADJ Series) K* with a M5 x 10 mm socket pin screw (C) C (Sold Separately) using security allen wrench (B). See detail 1. Screw extension column connector (I) to extension column. Align slot in extension column with one of the top holes in EXTENSION extension
ページ5に含まれる内容の要旨
Installation To Wood Joist Ceilings Drill two 5/32" (4 mm) dia. holes to a minimum depth 1 of 2.5" (64 mm). Attach ceiling plate (G) with two #14 x 2.5" (6 mm x 65 mm) wood screws (F) as shown using 3/8" (10 mm) socket wrench. Skip to step 2. WOOD JOIST WARNING CEILING • Tighten wood screws (F) so that wall plate (G) is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. G • Never tighten in excess of 80 in • lb (9 N.M.). • Make su
ページ6に含まれる内容の要旨
Installation to Concrete Ceilings WARNING • When installing Peerless mounts on concrete, verify that you have a minimum of 1 5/8" of actual concrete surface in the 1/4" diameter hole to be used for the concrete anchors. Do not drill into mortar joints! Concrete must meet ASTM C-90 specifications. • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Make sure that the supporting surface will safely support the combined load of the equipment and all
ページ7に含まれる内容の要旨
Flush Mount Application Screw projector mount (A) into ceiling plate (G). Align the notch with one of the four holes of the ceiling 1 plate (G) and secure projector mount (A) with a M5 x 10 mm socket pin screw (C) using security allen wrench (B) as shown in detail 1. NOTE: Slotted set screw (K) is used to jam against the threads of mount to prevent any excess movement of the projector mount (A). Do not overtighten screw; overtightening screw will damage threads making it difficult to separate th
ページ8に含まれる内容の要旨
Attach adapter plate (L) to projector using one LEG M,N, O 3 screw (M, N, O or P) for each channel as shown. or P Tighten all screws, while keeping the center of gravity. Be sure that adapter plate (L) is straight. Adjust the feet of the channels to keep the adapter plate level. Tighten L all screws with 4 mm security allen wrench (B) or wrench provided with projector mount, while keeping the FOOT OF center of gravity. If M3 screws are used, tighten using 2 CHANNEL mm security allen wrench (Q).
ページ9に含まれる内容の要旨
Projector Alignment To adjust roll, pitch and yaw loosen the set screw (shown 5 below) using allen wrench (B). You should be able to just slightly loosen the screw so that your adjustments can be set without having to hold the projector. Move projector SET to desired position and slowly tighten set screw. SCREW IMPORTANT: Allen wrench is your key for projector removal. Store it in a safe place. PROJECTOR Accessories NOTE: All accessories are available for purchase through Epson (www.epson.com) E
ページ10に含まれる内容の要旨
LIMITED FIVE-YEAR WARRANTY www.peerlessmounts.com © 2007 Peerless Industries, Inc. ISSUED 03/17/06 LIT-0190E 10 of 10 ISSUED: 01-23-07 SHEET #:055-9498-1 Visit the Peerless Web Site at www.peerlessmounts.com For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870. © 2008, Peerless Industries, Inc. All rights reserved. Epson is a registered trademark and Epson Exceed Your Vision is a trademark of Seiko Epson Corporation
