ページ1に含まれる内容の要旨
Owner’s Manual
Network Set-up and Operation
For Windows
Wired and Wireless Setting
Projector Set-up and Operation
Network Capture
Network Viewer
Moderator Function
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic operation of the
projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.
ページ2に含まれる内容の要旨
Compliance Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communicatio
ページ3に含まれる内容の要旨
The CE Mark is a Directive conformity mark of the The Alert Mark is a Directive conformity mark of the European Community (EC). European Community. Hereby, SANYO Electric Co., Ltd., declares that this WLAN Module (QXXAVC922---P) is in compliance English with the essential requirements and other relevant provisions of Directive 1999/5/EC. Česky SANYO Electric Co., Ltd. tímto prohlašuje, že tento WLAN Module (QXXAVC922---P) je ve shodě se [Czech] základními požadavky a dalšími příslušnými usta
ページ4に含まれる内容の要旨
Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a safety check regularly and take particular care to its environment. Incorrect installation may cause fire or other accidents. CAUTION IN USING NETWORK FUNCTION ● SANYO Electric Co., Ltd. assumes no
ページ5に含まれる内容の要旨
Table of contents Compliance .........................................................................................................................................................2 Safety instructions ............................................................................................................................................4 Table of contents ........................................................................................................................................
ページ6に含まれる内容の要旨
How to use the setting page .....................................................................................................................46 Initial setting ....................................................................................................................................................48 Network configuration ................................................................................................................................51 Configuring wireless LAN setting
ページ7に含まれる内容の要旨
Operating environment and configuration Required operating environment for computers When operating the projector via the networks, computers should meet the operating environment below. Microsoft Windows 2000 or Microsoft Windows XP or OS Microsoft Windows Vista (32bit version) Pentium 3 ; 1GHz or higher (more than 2GHz is recommended) for Windows 2000 CPU or Windows XP Pentium 4 ; 3GHz or higher for Windows Vista 256MB or more for Windows 2000 or Windows XP Memory 1GB or more for Windows
ページ8に含まれる内容の要旨
Network specifications of the projector LAN Terminal Data communication speed 100Base-TX (100Mbps)/10Base-T (10Mbps) Protocol TCP/IP Wireless LAN Interface IEEE802.11b/g AdHoc, Communication Mode Infrastructure 1/2/5.5/11Mbps (IEEE802.11b) Data Transfer Speed 6/9/12/18/24/36/48/54Mbps (IEEE802.11g) Wireless Frequency (Channel) 2412MHz–2462MHz (CH1–CH11) IEEE802.11g OFDM 54/4Mbps 64QAM, 36/24Mbps 16QAM, 18/12Mbps Modulation Form QRSK, 9/6Mbps BPSK IEEE802.11b DSSS 11/5Mbps CCK, 2Mbps DQPSK, 1Mbp
ページ9に含まれる内容の要旨
Chapter 1 1. About LAN functions This chapter describes the features, the mechanism, and connection procedures of the LAN.
ページ10に含まれる内容の要旨
Chapter 1 About LAN functions LAN functions and the features This product is loaded with a LAN network function which enables you to project an image on the computer through a projector via Network with dedicated software. With the software, you can also manipulate the projecting image and the projector. This software has functions below and you can use the projector under various network environments to meet the wide-ranging needs of the operation. • Accept both Wired and Wireless LAN envi
ページ11に含まれる内容の要旨
An example of the connection An example of the connection The illustration below shows an example of the projection via the LAN. You can project the image on Computer (1) (Wired LAN connection), or Computer (2) (Wireless LAN connection) through the selected projector . 2.0 2.0 1.5 1.5 1.0 1.0 0.5 0.5 0.0 0.0 2.0 1.5 1.0 0.5 0.0 Computer (2) Computer (1) Access point 11
ページ12に含まれる内容の要旨
Chapter 1 About LAN functions LAN connection modes Connection modes differ depending on the LAN and computer environments. Connect appropriately for each environment. ■ Wireless LAN, Infrastructure Communication Mode Communicate over an access point between Wired LAN equipment and Wireless LAN equipment. Or, communicate over an access point among multiple Wireless LAN equipment. Wireless LAN equipment will select an access point to communicate SSID/ESSID modes. These communication modes a
ページ13に含まれる内容の要旨
LAN connection modes ■ Wired LAN Communication Mode Communicate via the LAN line. Computer(1) Computer(2) Computer (3) ✳ Operate the computer mouse with the remote control. When the projector’s remote control employs mouse operating function, you can operate the computer by the remote control which is provided with the projector. To use the remote control, point to the projector. You do not need to connect the USB cable to operate the computer mouse. (For details about the remote contro
ページ14に含まれる内容の要旨
Chapter 1 About LAN functions 1
ページ15に含まれる内容の要旨
Chapter 2 . S etup procedures This chapter describes how to install the Network Capture 5 software and how to set up the networks. 15 1
ページ16に含まれる内容の要旨
Chapter 2 Setup procedures To use the projector via the networks, follow the setup procedures below. Install the software on computers. STEP 1 Install the software recorded in CD-ROM on each computer which will be operated. Read following pages of this chapter to install. Select Wired LAN or Wireless LAN then connect the STEP 2 LAN and set the configuration. Decide depending on the LAN environment. Wired LAN ............ Refer to “4. Wired LAN Configurations” (pp.25–31). Wireless LAN ....... R
ページ17に含まれる内容の要旨
Installing the software Installing the software It is required to install the software into your computer to use the Network Capture function . Please install the software as follows. Note: To install the software into the computer with Windows 2000, Windows XP or Windows Vista, you should logon as administrator. Before installation, make sure that the other applications are closed, otherwise proper installation cannot be made. Network Viewer & Capture 5 installation 1 Set the supplied Net
ページ18に含まれる内容の要旨
Chapter 2 Setup procedures As the "License Agreement" will appear, read contents carefully and click Yes button if you agree to the license agreement to proceed with installing. During the installation, following window may appear, click Continue Anyway button. 3 Click Finish to complete the installation. 1
ページ19に含まれる内容の要旨
Installing the software Installed software The following 3 softwares are installed on your computer. ● Network Capture : Captures the displayed image and the sound of the computer and serves them to the projector via the network. ● Network Viewer (File Converter 1): 1 Converts to the JPEG* data format which can be projected with the projector from the JPEG, bitmap and Power Point files. ● Network Viewer (P rogram Editor) : This is a tool to make the program which has a function to speci
ページ20に含まれる内容の要旨
Chapter 2 Setup procedures File Converter 2 installation 1 Set the supplied Network Viewer & Capture 5 CD- ROM into the CD-ROM drive of your computer. Double click SetupDrv.exe icon in the "Driver" folder in the CD-ROM. 2 S elect "English [United States]" from the pull-down menu on the language selection window and then click Install button to start installing. Installed software and places Network Viewer 5 (File Converter 2) is installed in the "Printers and Faxes" folder in the "Control
