ページ1に含まれる内容の要旨
Multimedia Projector
MODEL PLC-XU60
PLC-SU60
Owner’s Manual
ページ2に含まれる内容の要旨
Table of Contents Table of Contents 2 Computer Input 25 Input Source Selection 25 To the Owner 3 Computer System Selection 26 Computer Adjustment (Auto) 27 Computer Adjustment (Manual) 28 Safety Instructions 4 Image Level Selection 30 Image Level Adjustment 31 Installing the Projector in Proper Position 5 Screen Size Adjustment 32 Air Circulation 5 Moving the Projector 5 Video Input 33 Compliance 6 Input Source Selection Connecting the AC Power Cord 7 {Video, S-Video and (Y, Pb/Cb, Pr/Cr)} 33 In
ページ3に含まれる内容の要旨
To the Owner Before operating this projector, read this manual thoroughly Safety Precaution and operate the projector properly. This projector provides many convenient features and WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC functions. Operating the projector properly enables you to SHOCK, DO NOT EXPOSE THIS APPLIANCE manage those features and maintains it in better condition for TO RAIN OR MOISTURE. a considerable time. – This projector produces intense light from the projection Imprope
ページ4に含まれる内容の要旨
Safety Instructions All the safety and operating instructions should be read before This projector should be operated only from the type of power the product is operated. source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or Read all of the instructions given here and retain them for later local power company. use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp
ページ5に含まれる内容の要旨
Safety Instructions Installing the Projector in Proper Position Install the projector properly. Improper installation may reduce the lamp lifetime and cause a fire hazard. 20˚ Do not put the projector on either Do not tilt the projector more than side to project an image. 20 degrees above and below. 20˚ NO SIDEWAYS Do not point the projector down Do not point the projector up to to project an image. project an image. NO DOWNWARD NO UPWARD Air Circulation Openings in the cabinet are prov
ページ6に含まれる内容の要旨
Compliance Federal Communication Commission Notice Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communic
ページ7に含まれる内容の要旨
Compliance Connecting the AC Power Cord This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power being supplied. Connect the projector with all perip
ページ8に含まれる内容の要旨
Features and Design This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology. Compact Design Power Management This projector is extremely compact in size and weight. The Power management function reduces power It is designed to be carried and work anywhere you wish consumption and maintain the
ページ9に含まれる内容の要旨
Part Names and Functions q Infrared Remote Receiver Front w Auto Set Up Sensor t y Read screen condition in Auto Set Up operation. Do not cover or dirt this sensor face. See page 21. Remove the protection sheet on the sensor when you install the projector. With this sheet attached, the Auto Set Up operation may not q work properly. w e Lens Cover (See page 56 for attaching.) r Projection Lens t Top Controls and Indicators y Lamp Cover u Exhaust Vent CAUTION Hot air is exhausted from the exhaust
ページ10に含まれる内容の要旨
Part Names and Functions Terminal q w e r t COMPUTER IN 1 COMPUTER IN 2 / MONITOR OUT R - AUDIO IN - L (MONO) DVI - I SERVICE PORT S - VIDEO VIDEO / Y – Pb/Cb – Pr/Cr AUDIO IN 1 AUDIO IN 2 AUDIO OUT USB * USB RESET MCI (VARIABLE) Do not press this button. This button y u i o !00 is used for optional accessories. y USB (Series B) q COMPUTER IN 1 DVI-I When operating the connected computer with the remote Connect computer output (Digital/Analog DVI-I type) or Multi control, c
ページ11に含まれる内容の要旨
Part Names and Functions Top This projector has control buttons and indicators on its top. q w y e u i r t o !0 !1 !2 q POWER ON–OFF button i LAMP REPLACE indicator Turns the projector on or off. (p19) Turns yellow when the life of the projection lamp draws to an end. (p45, 49) w AUTO SET UP button o POINT (Up/Down/Left/Right ) button Operate AUTO SET UP function. (p21) Selects an item or adjusts value in the On-Screen Menu. These e ZOOM/FOCUS button are also used to pan the image in the Digi
ページ12に含まれる内容の要旨
+ E M U L O V Part Names and Functions q L-CLICK button Acts as left click for wireless mouse operation. (p14) Remote Control w SIGNAL EMISSION indicator This indicator lights red while the laser beam is being emitted from the laser light window or a signal is being sent from the remote control to the projector. e AUTO PC button Operates the Auto PC adjustment function. (p27) r D.ZOOM buttons Selects the Digital zoom +/– mode and resize the image. (p32) q t FREEZE button Freezes the projected pi
ページ13に含まれる内容の要旨
+ + E E M M U U L L O O V V Part Names and Functions Laser Pointer Function This remote control emits a laser beam as Laser pointer function from the laser light window. When the LASER button is pressed, laser light goes on. When the LASER button is being pressed for more than 1 minute or the LASER button is released, light goes off. The signal emission indicator lights red and laser is emitted with red light to indicate laser beam is being emitted. The laser emitted is a class II laser; ther
ページ14に含まれる内容の要旨
+ + E E M M U U L L O O V V Part Names and Functions Remote Control Code This projector has eight different remote control codes (Code 1-Code 8); the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). This switching function prevents remote control interference when operating several projectors or video equipment at the same time. (Change the remote control code for the projector first before changing that for the remote control. See “Remote control” on page 42.)
ページ15に含まれる内容の要旨
Part Names and Functions Remote Control Operating Range Point the remote control toward the projector (Infrared Remote Receiver) whenever pressing any button. Maximum operating range for the remote control is about 16.4’ (5m) and 60° in front of the projector. 16.4’ 16.4’ (5 m) (5 m) 60° 60° Remote Control Batteries Installation Remove the battery Slide the batteries into Replace the compartment 12 3 compartment lid. the compartment. lid. Two AA size batteries Press the lid down- For correct po
ページ16に含まれる内容の要旨
Installation Positioning the Projector This projector is designed to project on a flat projection surface and can be focused from 4.3’(1.3m) - 33.1’(10.1m). Refer to the figure and the table below for the screen size and the distance between the projector and the screen. A : B = 9 : 1 33.1' (10.1m) (Inch Diagonal) 300” 25.3' (7.7m) Max. Zoom 16.4' (5.0m) 231” 10.8' (3.3m) 231” 150” Min. Zoom A 4.3' (1.3m) 178” 100” 115” 40” 77” 31” (Center) B Screen Size 40” 100” 150” 231” 300” (W x H) mm 81
ページ17に含まれる内容の要旨
Installation Connecting to a Computer Cables used for connection (✽ = These accessories are not supplied with this projector.) • VGA Cable (HDB 15 pin) ✽ • USB Cable • DVI-VGA Cable (HDB 15 pin) • MAC Adapter (When connecting to Macintosh computer) ✽ • DVI-Digital Cable (for Single Link T.M.D.S.) ✽ • Audio Cables ( Mini Plug (stereo) x 2) ✽ IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA) Desktop type Laptop type Monitor Output Monitor Output Monitor Output USB port or Au
ページ18に含まれる内容の要旨
Installation Connecting to Video Equipment Cables used for connection (✽ = These accessories are not supplied with this projector.) • Video Cable (RCA x 1) ✽ • Audio Cables (Mini Plug (stereo) x 2 or RCA x 2) ✽ • Video Cable (RCA x 3) ✽ • Scart-VGA Cable ✽ • S-VIDEO Cable ✽ Video Source (example) Component video output equipment. (such as DVD player or high-definition TV source.) Video Disc Player Video Cassette Recorder S-VIDEO
ページ19に含まれる内容の要旨
Basic Operation Turning On the Projector Complete peripheral connections (with a computer, VCR, etc.) 1 before turning on the projector. 26 Connect the projector's AC power cord into an AC outlet. The 2 POWER indicator flashes red in a moment and turns on red. Press the POWER ON-OFF button on the top control or on the 3 remote control. The POWER indicator turns green, and the cooling fans start to operate. The preparation display appears on the screen and the count down starts. (A capture
ページ20に含まれる内容の要旨
Basic Operation Zoom Adjustment Press ZOOM/FOCUS button on Top Control or ZOOM / 1 button on Remote Control Unit. The message “Zoom” is displayed. Zoom Press ZOOM button or POINT UP button to make image 2 larger, and press ZOOM button or POINT DOWN button to make image smaller. Message disappears after 4 seconds. Focus Adjustment Press ZOOM/FOCUS button on Top Control or FOCUS / 1 button on Remote Control Unit. The message “Focus” is displayed. Focus Adjust focus of image by pressing F
