ページ1に含まれる内容の要旨
KODAK EKTAPRO
7010/7020/9010/9020
Slide Projector
SUPPLEMENT TO THE MANUAL
©Eastman Kodak Company, 2000
ページ2に含まれる内容の要旨
Function Codes This label is designed to be fixed on the rear of your IR Remote System (transmitter). Function Code • Dissolve times 801 - 899 (0.1 - 9.9 s) CUT 800 Random Access 0-160 Fade: MASTER 770 SLAVE 707 Alternate 777 Freeze 789 • Independent 980 Projector Control Mode • Parallel 970 projection 666* * Focus Slave • Reactivating 990 dissolve mode • Remote Security 989 Mode Reset 999 Autotimer 601 - 660 (1-60 s) ----- off 600 * Function is inactivated for models 7010 and 9010! 5
ページ3に含まれる内容の要旨
Comments Presentations with KODAK EKTAPRO 7010, • Even when the two projectors are linked with the dissolve 7020, 9010 and 9020 Slide Projectors cable, they behave like individual projectors and can also One of the important new features of the KODAK EKTAPRO be operated individually as usual via the keypad. 7010, 7020, 9010 and 9020 Slide Projectors is the integrated • If your SLAVE projector has a built-in timer, it must be dissolver for a 2-projector dissolve. switched off! You just have to li
ページ4に含まれる内容の要旨
COMMANDS AND EFFECTS Overview Examples: DISSOLVE If you want a dissolve time of The following table gives and Basic setting 1 s :➔ Input <810> and confirm with <*>. overview of all commands and effects. After switching on you can 5.5 s :➔ Input <855> and confirm with <*>. All commands with * can also be used immediately begin a dissolve 0 s (Hard Cut) :➔ Input <800> and confirm for projection with a single presentation. Dissolving takes place with <*>. EKTAPRO 7010, 7020, 9010 or 9020 with a def
ページ5に含まれる内容の要旨
*Random Access Further control facilities *FREEZE (789) You select slides in 2 projector dissolve With the commands “Fade With the Freeze command a soft according to the slide number of your MASTER”, “Fade SLAVE” and dissolve can be stopped at any time presentation and not according to the “Alternate” you can carry out (resp. fade in and fade out by single slide tray number (see the table on dissolves without a slide transport projection) and in any position. The page 34)! afterwards. When a dis
ページ6に含まれる内容の要旨
Transport control on the MASTER: hitches” can occur if the presenter *AUTOTIMER (600...660) The slide transport runs, as usual, via presses the wrong button on the remote A Timer function can also be set via the the two transport buttons. control by accident. IR remote control. This is particularly Transport control on the SLAVE: With the security setting you can set up relevant for the EKTAPRO 7010/7020 The slide transport is via the two focus your remote control so that when the as this does n
ページ7に含まれる内容の要旨
Slide Sorter Aid Position Position Position Position Position Position Position Position Slide in Slide in Slide in Slide in in SLAVE in SLAVE in SLAVE in SLAVE No. MASTER No. MASTER No. MASTER No. MASTER tray tray tray tray tray tray tray tray 0 0 41 21 82 41 123 62 1 1 42 21 83 42 124 62 2 1 43 22 84 42 125 63 3 2 44 22 85 43 126 63 4 2 45 23 86 43 127 64 5 3 46 23 87 44 128 64 6 3 47 24 88 44 129 65 7 4 48 24 89 45 130 65 8 4 49 25 90 45 131 66 9 5 50 25 91 46 132 66 10 5 51 26 92 46 133 67 1
