5.5 STORAGE AFTER USE ....................................................................................23 CHAPTER 6 Q & A................................................................................................24 English - 2
Chapter 1 Precautions Always follow these safety instructions when setting up and using the Digital Presenter: 1. Do not place the Digital Presenter on an unstable trolley, stand or table. 2. Do not use the Digital Presenter near water or source of heat. 3. Use attachments only as recommended. 4. Use the type of power source indicated on the Digital Presenter. If you are not sure of the type of power available, consult your dealer or local electricity company for advice. 5. Place the D
ページ6に含まれる内容の要旨
If the power cable or plug becomes damaged or frayed. If liquid is spilled into it or the Digital Presenter has been exposed to rain or water. Safety Precautions Warning: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. This Digital Presenter has a 3 wires AC line Plug. This is a safety feature to ensure that the plug will fit into the power outlet. Do not try to defeat this safety feature. If the Digital Presenter will not be used f
ページ7に含まれる内容の要旨
This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room or auditorium. English - 6
ページ8に含まれる内容の要旨
Chapter 2 Package Content Please make sure the package comes with the following items when you unpack: PS600 Quick start guide User Manual CD Power Cable USB Cable C-Video Cable VGA Cable Remote Control English - 7
ページ9に含まれる内容の要旨
Chapter 3 Product Overview 3.1 Front View/ Rear View 1. Camera Head 2. Camera Arm 3. Lamp 4. Backlight 5. Remote Control Slot 6. CF card slot 7. Lamp lock 8. Control Panel 9. Button Function Guide 10. IR Sensor English - 8
ページ10に含まれる内容の要旨
3.2 Control Panel 1. Power： Power on/off 2. Source： Select PC or Camera to Projector 3. Lamp： Switch / on / off the lamp and backlight 4. Photo/Text： Select the photo or text mode 5. AF： Auto Focus 6. Brightness +/– Brightness Adjustment 7. Zoom + /– zoom in/out 8. A4/A5： Speedy zoom to A4/ A5 size 9. AWB/Shift： AWB is Auto White Balance; Shift function enables in PBP mode that can be shifted the other half 10. Capture Capture an image into internal memory or storage
ページ11に含まれる内容の要旨
3.3 I/O Connector 1. VGA IN Connect to VGA-out of other device for example PC 2. VGA OUT Connect to VGA-in of another visual device 3. DVI OUT Digital & Analog Receptacle Connector 4. LCD Monitor External small size LCD monitor 5. C-VIDEO C-Video for video output 6. Ethernet Ethernet connection For remote central control 7. USB ( support USB 1.1 ) Ethernet connection For remote central control 8. PS2 Connect with PS/2 mouse 9. RS232 Connect external device with RS232
ページ12に含まれる内容の要旨
3.4 Remote Control 1. Power： Power on/off 2. Capture： Capture image to internal memory 3. Source： Select PC or Camera to Output 4. AF： Auto Focus 5. PBP： Compare the live image and captured image 6. Menu： 15. Preset： Display full control menu Save/load your setting (OSD Menu) parameters (like brightness,) 7. BRT+/-： 16. Lamp： Brightness adjustment Switch / on / off the lamp and 8. Photo/ Text ： backlight 17. Focus +/-： Change between Photo or Text mode Manual focus for
ページ13に含まれる内容の要旨
Chapter 4 Installation 4.1 Setup the Digital Visualizer 1. Pull up the arm. Adjust the position and height (the height should be 48.5 cm for operation) of the arm by moving the 3-section joint 2. Turning the camera head toward the platform ※ Note：The angle of the camera head is limited. Don’t turn it forcefully when it reaches the maximal angle 4.2 Powering on the Digital Visualizer ※Note：Before using the Digital Presenter, make sure that you have connected it to the comput
ページ14に含まれる内容の要旨
4.3 Positioning and Turning on the Lamps You can use the lamps on the both sides of the Digital Presenter for auxiliary lighting by following some simple steps： 1. Press and slide the latches to release the lamp lock. 2. Pull up the lamp arms. 3. Rotate the folded lamp to face the platform as the arrow shows. (Refer to figure 4-1) 4. Press the lamp button of control panel and remote control to switch the side lamp or backlight. ※ Note： The angle of the lamp arm/lamp head is limited.
ページ15に含まれる内容の要旨
4.6 Using Ethernet The Digital Visualizer can be controlled via the internet. 1. Please connect the RJ-45 to Ethernet port (refer to the 3.3 I/O connection) 2. Select the setting of DHCP, IP, Net Mask and Gate Way. Please refer to the 5.4 Network setting steps. 3. Open the Internet Browser and key in the IP in the address field. The remote control will be shown as following then you can control the main unit remotely via internet. ※Note：If you can’t use the Ethernet , please consul
ページ16に含まれる内容の要旨
Chapter 5 Using the Digital Visualizer This chapter shows you the basic and advanced functions of the Digital Presenter as and how to use the menu, the mouse, and the Presenter USB/RS232 interface 5.1 Getting Started 5.1.1 Select Input Source Switch the video input from PC or Camera Option1：press button on the control panel Option2：press on the remote control ※Note：Input source can be shown on the indicator of control panel 5.1.2 Lamp adjustment Press (Lamp) on the
ページ17に含まれる内容の要旨
option2：press on the remote control ※Note：The digital visualizer will execute the Auto Focus after zoom in/ out Manual Focus option1：press +/- on the control panel option2：press ※Note：The optical zoom will be automatically switched to the digital zoom at the last step of the optical zoom 5.1.4 PBP Display current live image and captured image for side-by-side comparison ［A］ ［B］ live image 1/2 Capture image Option1：press select captured pictures
ページ18に含まれる内容の要旨
Rotate the camera head While observing the image on the monitor, adjust the zoom or arm to obtain the optimal size To rotate the image by 180º Optoin1：press
ページ19に含まれる内容の要旨
Option 2：press on the remote control 5.1.9 To show the captured image (Storage Play) Option 1：OSD／Storage ／Play In the Index screen, the captured images were displayed in thumbnails. Whenever the box is on a thumbnail, you may see the full and large image by Enter click. Option 2：Press on the remote control and select image by using keys then press the key to see the large image 5.1.10 To delete the captured image (Storage Delete) Option 1：OSD／Storage ／Delete ※Note：If you
ページ20に含まれる内容の要旨
5.2 Using the OSD Menu 5.2.1 Showing the Main Menu： Option 1：Press
