ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
EMP-735 User’s Guide Features of the Projector The vertical angle of the projector is detected, so that any vertical keystone distortion in the projected images can be automatically corrected.( p.31) When projecting computer images, the signals from the connected computer are detected automatically and adjusted so that the optimum images are projected. Even if several people are giving presentations using the same projector, the optimum picture quality can be obtained simply by disconnecting
ページ3に含まれる内容の要旨
EMP-735 User’s Guide Contents Features of the Projector .................................................................. 1 Before Using the Projector Part Names and Functions ............................................................... 5 Front/Top................................................................................................5 Control Panel..........................................................................................6 Rear ........................................
ページ4に含まれる内容の要旨
EMP-735 User’s Guide Contents Advanced Operations Functions for Enhancing Projection ................................................ 39 A/V Mute..............................................................................................39 Freeze ...................................................................................................40 Projects a Wide-screen Image During Image Projection of the Video Equipment ....................................................41 E-Zoom...........
ページ5に含まれる内容の要旨
Before Using the Projector This chapter describes the procedures for setting up the projector before use. Part Names and Functions .................................................5 • Front/Top................................................................................................ 5 Control Panel.......................................................................................... 6 Rear.............................................................................................
ページ6に含まれる内容の要旨
EMP-735 User’s Guide Part Names and Functions Front/Top • Zoom ring ( p.30) • (Warning) indicator Adjusts the image size. (p.63) Flashes or stays lit to indicate • Focus ring ( p.30) problems with the projector. Adjusts the image focus. • PC Card Slot ( EasyMP Setup Guide, EasyMP • Power indicator ( p.62) Flashes or lights in different Operation Guide) Insert a network card or memory colours to indicate the operating status of the card and use it with EasyMP. projector. • PC Card Access L
ページ7に含まれる内容の要旨
EMP-735 User’s Guide Part Names and Functions Control Panel • [Power] button ( p.26, 28) • [Help] button ( p.61) Turns the projector power on and off. Displays the online help menu to assist you if you have a problem. • [Source] button ( p.27) • [Keystone] button ( p.33) Scrolls through the input sources Press to manually correct (Computer/Component Video port → keystone distortion in images. S-Video port → Video port → EasyMP) When pressed whilst a help menu each time this button is pressed.
ページ8に含まれる内容の要旨
EMP-735 User’s Guide Part Names and Functions Rear • Video port ( p.20) • Audio-In port ( p.17, 23) Inputs composite video signals to Inputs audio signals. the projector from other video sources. Connect using a stereo mini Use the RCA video cable for this jack. connection. • Remote control light- • S-Video port ( p.21) receiving area ( p.9) Inputs S-Video signals to the Receives signals from the projector from other video sources. remote control. • Power inlet ( p.25) Connects the • Speaker
ページ9に含まれる内容の要旨
EMP-735 User’s Guide Part Names and Functions Remote Control • [Page down]/[Page up] • Remote control light- buttons ( p.18) emitting area ( p.10) Press these buttons to scroll Outputs remote control • [Power] button back and forth through pages signals. of a PowerPoint file when ( p.26, 28) using the remote control as a Turns the projector power wireless mouse or pages of a on and off. scenario when using EasyMP's CardPlayer. • [Color Mode] button • Input select buttons (p.37) (p.27)
ページ10に含まれる内容の要旨
EMP-735 User’s Guide Before Using the Remote Control Using the Remote Control and Remote Operating Range When using the remote control for the first time, pull out the insulating tape that is protruding from the battery holder. When the insulating tape is pulled out, the remote control can be used. Insulating tape Using the Remote Control The remote control is used in the following way. Procedure Point the remote control light-emitting area toward one of the remote control light-receiving are
ページ11に含まれる内容の要旨
EMP-735 User’s Guide Before Using the Remote Control Remote Operating Range Use the remote control within the ranges indicated below. If the distance or angle between the remote control and the remote control light-receiving area is outside the normal operating range, the remote control may not work. Operating distance Operating angle Approx. ±30º horizontally Approx. 6 m (20 ft.) Approx. ±15º vertically Approx. ±30º horizontally Remote control light-receiving area Within approx. 6 m (20f
ページ12に含まれる内容の要旨
EMP-735 User’s Guide Installation Setting Up the Projector The projector supports the following four different projection methods, allowing you to choose the best method for displaying your images. Caution : Before setting up the projector, be sure to first read the separate Safety Instructions/ World-Wide Warranty Terms. Front projection Rear projection using a translucent screen Front/ceiling projection Rear/ceiling projection using a translucent screen * A special method of install
ページ13に含まれる内容の要旨
EMP-735 User’s Guide Installation Screen Size and Projection Distance The distance between the projector and the screen determines the actual image size. Recommended distance 1.0–11.7 m (3.2–38.5 ft.) Whilst referring to the table below, position the projector so that the images are projected onto the screen at the optimum size. The values should be used as a guide for setting up the projector. The actual values will vary depending on projection conditions and the zoom setting. 4:3 Screen siz
ページ14に含まれる内容の要旨
EMP-735 User’s Guide Connecting to a Computer Caution : When connecting the projector to a computer, be sure to check the following. Turn off the power for both the projector and the computer before connecting them. If the power for either device is on at the time of connection, damage may result. Check the shapes of the cable connectors and the device ports before making the connections. If you try to force a connector to fit a device port with a different shape or number of terminals, d
ページ15に含まれる内容の要旨
EMP-735 User’s Guide Connecting to a Computer Projecting Images from the Computer The shape and specifications of the computer's monitor port will determine what type of cable should be used. Check the following to see which type of port your computer has. If the Monitor Port is a Mini D-Sub 15-pin Port Use the accessory computer cable to connect the Computer/Component Video port at the rear of the projector to the monitor port of the computer. To monitor port Computer cable To Computer/Compo
ページ16に含まれる内容の要旨
EMP-735 User’s Guide Connecting to a Computer If the Monitor Port is a 5BNC Port Use the optional VGA-HD15/BNC PC cable to connect the Computer/ Component Video port at the rear of the projector to the monitor port of the computer. See "Appendices: Optional Accessories" ( p.94) To monitor port VGA-HD15/BNC PC To Computer/Component cable (optional) Video port (blue) Tip : After starting projection, set to "Computer" by selecting "Video" - "Input Signal" on the configuration menu. ( p.45)
ページ17に含まれる内容の要旨
EMP-735 User’s Guide Connecting to a Computer If the Monitor Port is a 13w3 Port Some workstation-type computers have a 13w3 monitor port. Use a commercially-available 13w3 ⇔ D-Sub 15-pin cable to connect the Computer/Component Video port at the rear of the projector to the monitor port of the computer. To monitor port To Computer/Component 13w3 cable Video port (blue) (commercially-available) Tip : After starting projection, set to "Computer" by selecting "Video" - "Input Signal" on the
ページ18に含まれる内容の要旨
EMP-735 User’s Guide Connecting to a Computer Playing Sound from the Computer The projector has a single built-in speaker with a maximum output of 1 W. To output the audio of a computer with an audio output port from the built-in speaker, connect the audio output port of the computer and the Audio-In port (stereo mini jack) at the rear of the projector with either of the following commercially-available audio cables. 3.5ø Stereo mini jack audio cable 2RCA (L-R)/stereo mini jack audio (ze
ページ19に含まれる内容の要旨
EMP-735 User’s Guide Connecting to a Computer Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse Function) You can use the remote control as a wireless mouse to control the mouse pointer on the computer screen. To do this, you must use the accessory USB cable to connect the USB port of the computer to the USB port at the rear of the projector. Computer Mouse used Applicable cable Windows 98/2000/Me/ XP Home Edition/ USB mouse USB cable (accessory) XP Professional Macintosh
ページ20に含まれる内容の要旨
EMP-735 User’s Guide Connecting to a Computer Once the connection has been made, the mouse pointer can be operated as follows. Moving the mouse pointer Left click Press the [ ], [ ], [ ] or [ ] button to Press the [Enter] button. move the mouse pointer in the direction of If you press the [Enter] button twice in the button pressed. rapid succession, it has the effect of a double-click. Page down Page up Power Page down Page up Power Comp/Easy MP S-Video/Video Color Mode Comp/Easy MP S-Video/V
