ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
About the Manuals and Notations Used Types of Manual The documentation for your EPSON projector is divided into the following two manuals. Refer to the manuals in the order given below. Safety Instructions/World-Wide Warranty Terms This manual contains information on using the projector safely, and also includes a guide for warranty service, and a troubleshooting check sheet. Be sure to read this manual thoroughly before using the projector. User’s Guide (this manual) This User's Guide contain
ページ3に含まれる内容の要旨
Checking the Components When you unpack the projector, make sure that you have all these components. If any of the components are missing or incorrect, please contact the place of purchase. ❏ Projector (with lens cover) ❏ Remote control ❏ Power cable (3.0m) ❏ AA alkali batteries (2 pcs.) Connect to the projector and to a wall outlet. Insert into the remote control. Documentation ❏ Document CD-ROM ❏ D SCART adapter (Safety Instructions/World-Wide Use a commercially-available SCART cable to Warra
ページ4に含まれる内容の要旨
Table of Contents ■ Features of the Projector.............................4 Remote control .............................................7 ■ Part Names and Functions..........................6 Rear..............................................................8 Front / Top....................................................6 Base .............................................................8 Control panel ................................................6 ■ Appearance...............................
ページ5に含まれる内容の要旨
Table of Contents Troubleshooting ■ Problem Solving ........................................ 36 When the indicators provide no help.......... 37 •Problems relating to images................................. 38 Reading the indicators ............................... 36 •Problems when projection starts .......................... 43 • When the (warning) indicator is lit or •Problems with the remote control........................ 43 flashing..........................................................
ページ6に含まれる内容の要旨
Features of the Projector Image appearance can be selected to match the projection environment (Color Mode) The optimum images for the location can be projected simply by selecting the desired colour mode from the following six preset modes. If "Natural", "Theatre", "Theatre Black 1" or "Theatre Black 2" is selected, the Epson Cinema Filter effect is applied automatically to increase the contrast and to make skin tones appear with more natural tints. p.18 Dynamic Theatre Black1 Living R
ページ7に含まれる内容の要旨
Features of the Projector Equipped with a wide- angle lens shift function The lens shift function allows the position of the projected images to be adjusted vertically and horizontally without distorting the images. This can allow the projector to be set up with greater freedom, even if it is suspended from a ceiling or at an angle to the screen. p.16 Equipped with 2.1x short throw zoom lens For zoom adjustment, 2.1x short throw zoom lens is provided. Images can be projected onto an
ページ8に含まれる内容の要旨
Part Names and Functions Front / Top • Horizontal lens adjustment dial p.16 Moves the lens horizontally. • Vertical lens adjustment • Control panel See below dial p.16 Moves the lens vertically. • Remote control light- receiving area • Zoom ring p.16 p.13 Adjusts the image size. Receives signals from the remote control. • Focus ring p.16 • Air exhaust vent Adjusts the image focus. Do not touch the exhaust vent immediately after projecting, or while projecting, since it • Lens cover becomes
ページ9に含まれる内容の要旨
Part Names and Functions Remote control • Remote control light- emitting area p.13 • On/Off buttons p.14 • Indicator Outputs remote control signals. Turns the projector power on/off. Illuminates when remote control signals are being output. • Color Mode button p.18 Selects the colour mode. • Memory button p.24 Retrieves stored memories. • Aspect button p.18 Selects the aspect. • Menu button p.26 Displays the full-screen configuration menus. • Esc button p.18, 20, 24, 26 • button Pressing [
ページ10に含まれる内容の要旨
Part Names and Functions Rear • [Component] input port p.12 Connects to the component (YCbCr or YPbPr ) out port of the • [SCART] input port p.12 video equipment. Connects to the component (YCbCr or YPbPr) out port or D • [HDMI ] input port p.12 • [PC] input port p.12 out port of the video equipment. Connects to video equipment or a Connects to the RGB out computer that is HDMI- port of the computer. compatible. • [Trigger out] port • Remote control When the projector power light-receivin
ページ11に含まれる内容の要旨
Appearance Centre of projector Centre of lens 131.5 124 143 *1 66 19 *2 110 406 *1 Distance from centre of lens to suspension bracket fixing point (Lens shift amount: Max. 8.8 mm vertically) *2 Distance from centre of lens to centre of projector (Lens shift amount: Max. 7.7 mm horizontally) Centre of lens 300 52.8 77.3 310 160 4-M4×8 Units:mm 9
ページ12に含まれる内容の要旨
100" 100" Setting up Adjusting the projection size The size of the projected image is basically determined by the distance from the projector's lens to the screen. Lens shift Top Offset Centre of lens Offset Lens shift Bottom Adjusting the projection size The height from the centre of the lens to the bottom of the Projection distance screen will vary depending on the lens shift setting. While referring to the table below, position the projector so that the images are projected onto the scre
ページ13に含まれる内容の要旨
Setting up Projection methods Avoid setting the projector up in a place which is very dusty or humid, or where there will be cigarette or other smoke, especially oily smoke. Clean the air filter at least once every 3 months. Clean the air filter more frequently if using the projector in a dusty environment. A special method of installation is required when suspending the projector from the ceiling (ceiling mount). If it is not installed correctly, it could fall causing an accident and injury.
ページ14に含まれる内容の要旨
Connecting Image Sources • Turn the power off for both the projector and the signal source before connecting them. If the power for either device is on at the time of connection, damage may result. • Check the shapes of the cable connectors and the device ports before making the connections. If you try to force a connector to fit a device port with a different shape or number of terminals, a malfunction or damage to the connector or port may result. Video equipment (VHS VCR, DVD player, game
ページ15に含まれる内容の要旨
Preparing the Remote Control Inserting batteries into the remote control The remote control is not supplied with batteries already inserted. Insert the accessory batteries before using the remote control. Remove the battery cover. Install the battery cover. Insert the tab. While pressing the knob, lift up. Press down until the battery cover clicks into place. Insert the batteries. Check the (+) and (-) indications inside the battery compartment and insert the batteries so that they face cor
ページ16に含まれる内容の要旨
Projecting Images Turning the power on and projecting images Remove the lens cover. Turn the power on. Remote Control Control Panel Turn the power on for the connected equipment. Connect the power cable. Turn on the main power switch. ON If there is a problem with projection even though the projector is set up and connected correctly, refer to p.15, 36. If you set the "Direct Power On" to "On", the power of the unit will turn ON when the main power switch is turned ON, without having t
ページ17に含まれる内容の要旨
Projecting Images When the expected images are not projected If more than one signal source has been connected, or if no images are projected, use the remote control or the projector's control panel buttons to select the signal source. For video devices, press the [Play] button on the video equipment first, then select the signal source. Using the remote control Using the control panel When the expected images are not projected Turning the power off When you press , the menu is displaye
ページ18に含まれる内容の要旨
Adjusting the Projection Screen Focus adjustment Turn the focus ring to adjust the focus. Fine adjustments to image size (Zoom adjustment) Turn the zoom ring to adjust the size of the projected image. Wide Tele Focus adjustment Projection image position adjustment (Lens shift) Fine adjustments to image size (Zoom The lens shift function can be used to move adjustment) H the image display position vertically and horizontally within the range shown in the figure on the right when you cannot se
ページ19に含まれる内容の要旨
Adjusting the Projection Screen Correcting projector tilt If the projected images are tilted horizontally ( ), use the front adjustable feet to adjust the projector so that it is horizontal. Extend Retract Extend Retract Displaying a test pattern You can project a test pattern at times such as when setting up the projector in order to perform adjustments in the line menu, and zoom and focus adjustments without having to connect video equipment. If on the remote control is p
ページ20に含まれる内容の要旨
Basic Image Quality Adjustments Selecting the colour mode Selecting the colour mode Press and select the colour mode from the menu. Setting is also possible using the configuration menu. Selecting the aspect Selecting the aspect Press and select the aspect mode from the menu. Select Menu Operations Press or on the remote control or on on the projector's control When projecting using Auto panel to select an item. Press or to confirm the selec
