ページ1に含まれる内容の要旨
PjNET-300
OWNER'S MANUAL
LINK A C T
ページ2に含まれる内容の要旨
Compliance and Caution Compliance Federal Communication Commission Notice This equipment has been tested and found to comply EIKI PjNET-300 with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed Tested To Comply With FCC Standards to provide reasonable protection against harmful interference in a residential installation. This equip- FOR HOME OR OFFICE USE ment generates, uses and can radiate radio frequency energy and, if not installed
ページ3に含まれる内容の要旨
Compliance and Caution CAUTION ON USE IN NETWORK - When you receive an alert e-mail from the projector, you must check the projector immediately. Fire or accident may result if the projector is used in an abnormal condition. - When you install the projector at remote location and use it through the network, you must perform the safety inspections periodically. In this case you must pay attention to the change of environment in which you installed the projector. It may cause fire or an acc
ページ4に含まれる内容の要旨
Contents Compliance ..............................................................................................................2 Federal Communication Commission Notice .......................................................2 Trademarks ..........................................................................................................2 Contents ...................................................................................................................4 Chapter 1 Preparation ....
ページ5に含まれる内容の要旨
Contents Save the controls and settings ...........................................................................49 Save/delete the settings ....................................................................................49 Check the saved items ......................................................................................50 Load a control set ..............................................................................................50 Timer setting .............................
ページ6に含まれる内容の要旨
6
ページ7に含まれる内容の要旨
Chapter 1 1 Preparation Describes features and operating environment of this product. 7 7 OWNSER'S MANUAL ENGLISH
ページ8に含まれる内容の要旨
Chapter 1 Preparation Features Web Management function (☞p.39) With this function, you can monitor projector functions PC1 PC2 such as power status, lamp status, input mode, signal PJ2 PJ1 condition, lamp-use time, etc. through the network by using PC3 PC4 PC6 the web browser installed on PC5 Turn on PJ2. your computer. E-Mail Alert function (☞p.32) The projector (Network Unit) sends messages to the regis- PC1 PC2 tered e-mail addresses when a lamp abnormality or power PJ2 PJ1 failure
ページ9に含まれる内容の要旨
Features Multi-control function (☞p.56) A single computer can con- trol and set up the multiple projectors at the same time. PJ1 PJ2 PJ3 PJ4 PC6 PC5 PC4 Select Input 2 for PJ1 to PJ4 Automatic On/Off using Clock function (☞p.51) Automatically turn on or off the I am ready to turn ON, projectors at specified date/day and select Input 3 (Video) and time by using the clock function. Now it’s 11:30 Control port ready for external equipment (☞p.61) This product provides a serial port (RS- 232
ページ10に含まれる内容の要旨
Chapter 1 Preparation Operating environment To perform the managing and setting up the projector using this product, the environ- ment described below is required. Operating System 1 Standard mode* : Windows 98, Windows Me, Windows 2000, Windows NT4.0 SP6, Windows XP Network Network must handle Ethernet correctly and accept TCP/IP protocol. Computer The computer must provide a 10Base-T or 100Base-TX network card. Web browser application* ● Microsoft Internet Explorer version 5.0, 5.5 or
ページ11に含まれる内容の要旨
Operating environment *1 The limitation of connection between this product and hub or computer Suitable LAN cables are limited by length and type as follows; Connection Type of usable LAN cable Maximum length 2 Network Unit - Hub UTP Straight Cable with category 3 or 5 * 100m 2 Network Unit - Computer UTP Cross Cable with category 3 or 5* 100m *1 There may be other limitations depending on your network environment or LAN specification. Please consult your network administrator for further de
ページ12に含まれる内容の要旨
Chapter 1 Preparation Expression/Abbreviation The word "projector" found in this manual means "LCD projector provided with Network Unit" unless otherwise noted. The OS of the computer and the web browser described in this manual is Windows XP Professional and Internet Explorer 6.0. In case of another OS or web browser, some instruction procedures may differ from the actual operation depending on your com- puter environment. Use of this manual This manual does not provide the description of ba
ページ13に含まれる内容の要旨
Chapter 2 2 Installation Describes how to install the Network Unit, and configure the network. 13 OWNSER'S MANUAL ENGLISH
ページ14に含まれる内容の要旨
Chapter 2 Installation Flow of installation The following are instructions for attaching this product to the projector and connect- ing it to the network. Please review the entire procedure to become familiar with it. 1 Function of the Network Unit (☞ p.15) Explains the name and functions of each part of the Network Unit. 2 Installation and network configuration (☞ p.16-22) 1 Mount this product onto the projector. 2 Connect the LAN cable and join it to the network. 3 Configure the network of th
ページ15に含まれる内容の要旨
Name and function of each part [1] Name and function of each part (Top View) Power indicator This lights up red when the network function is set ON in the projector menu. Mounting screws Mount by using a coin etc. (☞ p.16) ACT indicator This turns on and off with green when sending or receiving of data LINK indicator This lights up orange when the Network Unit is connected to the net- work correctly. (Bottom View) Connector plug Connecting to the terminal on the pro- jector. (☞ p.16) Seria
ページ16に含まれる内容の要旨
Chapter 2 Installation [2] Installation and network configuration Mounting 1 Disconnect the AC plug from the projector. Connector cover 2 Remove the connector cover and screw covers (2 pieces) from the projector and insert plug on this product to the option connector. Screw cover 3 Tighten two screws by using a coin etc. ! Caution ✐ A C cord must be disconnected when mounting or removing this product otherwise it may damage the product. ✐ Do not install multiple Network Units into a p
ページ17に含まれる内容の要旨
Installation and network configuration Connection of LAN cable To connect to the network, it is required to use the UTP (Unshielded Twisted Pair) straight cable with RJ-45 plug. There are two different types of cables depending on whether the network is constructed with 10Base-T or 100Base-TX. Prepare the Hub (10Base-T or 100Base-TX) to distribute the network cable if required. 1 Disconnect the AC plug from the projector. 2 Connect the UTP straight cable to the LAN port on the Network Uni
ページ18に含まれる内容の要旨
Chapter 2 Installation Network configuration Confirmation of the network menu When installing this product to the projector, the network on-screen menu items for this product are activated automatically. If not activated, the product may not have been installed correctly. Please check item "Mounting" (☞ p.16). Configure the network Before performing the network configuration, prepare network address numbers (IP Address, Subnet Mask, Default Gateway, DNS) assigned to the projector. Ask your
ページ19に含まれる内容の要旨
Installation and network configuration 1 2 2 Configuration for IP Address/ Sub net/ Gateway* /DNS* Press SELECT button again. The following network setting pallet appears on the screen. Enter the specified network addresses. The red frame moves sequentially left or right with 7 8 button. The number up or down with d e button. How to enter the numbers There are 2 ways to enter the numbers, one is by using the point buttons (d e ) on the remote control or on the projector, the other is by u
ページ20に含まれる内容の要旨
Chapter 2 Installation Network PIN code setting The network PIN code can be set to restrict access to the setting page of the projec- tor using the web browser. ✽ Default network PIN code [0000] means no network PIN code is set. 1 Displaying network PIN code menu Select network menu and then select "Network PIN code" sub menu. Press SELECT button twice to display the Network PIN code entry pallet. * The number on the pallet is the current network PIN code. The red frame moves sequentially l
