ページ1に含まれる内容の要旨
MULTIMEDIA PROJECTOR
MODEL LC-HDT10
✽ Projection lens is optional.
OWNER'S INSTRUCTION MANUAL
ページ2に含まれる内容の要旨
TO THE OWNER Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual
ページ3に含まれる内容の要旨
SAFETY INSTRUCTIONS All the safety and operating instructions should be read before This projector should be operated only from the type of power the product is operated. source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or Read all of the instructions given here and retain them for later local power company. use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp
ページ4に含まれる内容の要旨
COMPLIANCES Federal Communication Commission Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful inter
ページ5に含まれる内容の要旨
TABLE OF CONTENTS FEATURES AND DESIGN 6 DISPLAY ADJUST 28 DISPLAY ADJUSTMENTS 28 SCREEN ADJUSTMENTS 28 PREPARATION 7 AUTO PC ADJUSTMENT 29 MANUAL DISPLAY ADJUSTMENTS 30 IMAGE ADJUSTMENTS 32 NAME OF EACH PART OF PROJECTOR 7 IMAGE LEVEL SELECT 32 SETTING-UP PROJECTOR 8 IMAGE LEVEL ADJUSTMENTS 33 CONNECTING AC POWER CORD 8 LENS INSTALLATION 9 POSITIONING PROJECTOR 9 SETTING 35 LENS SHIFT ADJUSTMENT 9 PICTURE LEVEL AND TILT ADJUSTMENT 10 MOVING PROJECTOR 10 SETTING MENU 35 CONNECTING PROJECTOR 11 AP
ページ6に含まれる内容の要旨
FEATURES AND DESIGN This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology. Power Management Compatibility Power Management function is provided to reduce power This projector widely accepts various video and consumption while a projector is not in use. computer input signals including; This P
ページ7に含まれる内容の要旨
PREPARATION NAME OF EACH PART OF PROJECTOR FRONT OF CABINET SPEAKERS INFRARED POWER CORD REMOTE RECEIVER CONNECTOR PROJECTION LENS MAIN ON / OFF SWITCH LENS COVER CARRYING HANDLE CAUTION Do not turn on a projector with lens cover LEVEL AND TILT ADJUST HANDLE attached. High temperature from light beam may damage lens cover and result in fire hazard. BACK OF CABINET INFRARED EXHAUST VENT REMOTE RECEIVER HOT AIR EXHAUSTED ! Air blown from exhaust vent is hot. When using or installing a projecto
ページ8に含まれる内容の要旨
PREPARATION SETTING-UP PROJECTOR CONNECTING AC POWER CORD This projector uses nominal input voltages of 120 V or 200-240 V AC. This projector automatically selects correct input voltage. It is designed to work with single- phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of type of power supply being in use. Connect a projector with p
ページ9に含まれる内容の要旨
PREPARATION LENS INSTALLATION Before setting up a projector, install Projection Lens on a Projector. 1. Before installation, check where a projector is used and prepare suitable lens. For specifications of Projection Lens, refer to manual separately attached or contact sales dealer where you purchased a projector. 2. For installation, refer to installation manual supplied to a Projector. When moving or setting up a projector, be sure to replace a Lens Cover to protect a surface. And be careful
ページ10に含まれる内容の要旨
PREPARATION PICTURE LEVEL AND TILT ADJUSTMENT REAR ADJUSTABLE Picture tilt and projection angle can be adjusted with FEET. (Refer to P7). handles on both sides of a projector. Projection angle can be adjusted to 5.7 degrees upper way. LEVEL AND TILT ADJUST HANDLE Press knob on handle. Handle pop out. KNOB 1 Turn handles (right and left) until picture is projected on 2 proper position. Adjust height of rear adjustable feet by rotating them until projector properly stabled on table. Press knob
ページ11に含まれる内容の要旨
CONNECTING PROJECTOR TERMINALS OF PROJECTOR This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from computers and video equipment. 4-built-in Terminal Slots enable you to arrange desired combinations of input sources just by changing Terminal Boards. For Terminal Boards, contact sales dealer where you purchased a projector. 3 TERMINAL SLOTS (Factory set) SERIAL PORT IN SDI IN1 SDI IN2 SDI OUT SDI Terminal SERIAL PORT OUT AUDI
ページ12に含まれる内容の要旨
CONNECTING PROJECTOR INPUT/OUTPUT TERMINALS AND JACKS INPUT 1 INPUT 1 INPUT 2, 3 SDI INPUT JACKS SDI OUTPUT JACK AUDIO INPUT JACKS Connect SDI output from Connect SDI input from Connect audio output video equipment to these video equipment to this from computer or video jacks. (Refer to P15.) jack. (Refer to P15.) equipment to these jacks. (Refer to P14, 15.) SERIAL PORT IN SDI IN1 SDI IN2 SDI OUT AUDIO CONTROL PORT SERIAL PORT OUT R/Pr G/Y B/Pb H/HV V R L (MONO) AUDIO CONTROL PORT R/C JACK USB
ページ13に含まれる内容の要旨
CONNECTING PROJECTOR USB PORT (Series B) SERIAL PORT IN TERMINAL This port is used to control a projector with computer. If you control a projector by computer, Connect USB port of computer to this you must connect a cable (not provided) port. from your computer to this terminal. SERIAL PORT IN SDI IN1 SDI IN2 SDI OUT SERIAL PORT OUT TERMINAL AUDIO CONTROL PORT SERIAL PORT OUT This terminal outputs signal R/Pr G/Y B/Pb H/HV V R L from SERIAL PORT IN. More than two projectors can be (MONO) c
ページ14に含まれる内容の要旨
CONNECTING PROJECTOR CONNECTING TO COMPUTER Cables used for connection (✽ = Cables are not supplied with this projector.) • DVI Cable NOTE : • DVI-VGA Cable (HDB 15 pin) When connecting cable, power cords of both a • MAC/VGA Adapter projector and external equipment should be disconnected from AC outlet. Turn a projector • BNC Cable (BNC x 5) ✽ and peripheral equipment on before computer is • Audio Cables (RCA x 2) ✽ switched on. IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA
ページ15に含まれる内容の要旨
CONNECTING PROJECTOR CONNECTING TO VIDEO EQUIPMENT Cables used for connection NOTE : • Video Cable (BNC)✽ When connecting cable, power cords of both a • Audio Cable (RCA x 2) ✽ projector and external equipment should be disconnected from AC outlet. Turn a projector • Scart Cable ✽ and peripheral equipment on before computer is • DVI-VGA Adapter ✽ switched on. (✽ = Cables are not supplied with this projector.) Video Source (example) Component video output equipment. Video Equipment with Video Eq
ページ16に含まれる内容の要旨
BEFORE OPERATION SIDE CONTROLS AND INDICATORS REAR INDICATORS SIDE CONTROLS FRONT INDICATORS SIDE CONTROLS POWER ON–OFF button ZOOM buttons FOCUS buttons VOLUME buttons Adjust zoom. (P23) Adjust focus. (P23) Adjust volume. (P24) Turns the projector on or off. (P22) ZOOM FOCUS VOLUME ON-OFF MENU button LENS SHIFT button Open or close the On-Screen Select LENS SHIFT function. Menu operation. (P20, 21) (P23) SELECT button MENU LENS SHIFT INPUT 1/2 INPUT 1/2 button Executes the item selected. (P20)
ページ17に含まれる内容の要旨
LAMP READY WARNING TEMP. LAMP REPLACE BEFORE OPERATION INDICATORS FRONT INDICATORS LAMP READY WARNING TEMP. LAMP REPLACE LAMP REPLACE indicator LAMP indicator WARNING TEMP. indicator READY indicator This indicator flashes red This indicator is dim when a This indicator lights green This LAMP REPLACE when internal projector projector is turned on. And when a projector is ready to indicator lights yellow when temperature is too high. bright when a projector is in be turned on. And it flashes any
ページ18に含まれる内容の要旨
BEFORE OPERATION OPERATION OF REMOTE CONTROL q SELECT button Executes the item selected. (P20) w SIGNAL EMISSION indicator This indicator lights red while a signal is being sent from the remote control to the projector. e SCREEN button Select image screen. (P28) r ZOOM button q Adjust zoom. (P23) t FREEZE button Freezes the projected picture. (P23) y MUTE button Mutes sound. (P24) u FOCUS button Adjust focus. (P23) i POINT (UP/DOWN/LEFT/RIGHT) button Selects an item or adjusts value in the On-Sc
ページ19に含まれる内容の要旨
BEFORE OPERATION Remote Control Code Change and Operating Range Code Change Operating Range This projector has eight different remote control codes (Code 1-Code 8); the Point Remote Control Unit toward factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). projector (Receiver Window) This switching function prevents remote control interference when operating whenever pressing any button. several projectors or video equipment at the same time. (Change the remote Maxim
ページ20に含まれる内容の要旨
BEFORE OPERATION OPERATING ON-SCREEN MENU ON-OFF ZOOM HOW TO OPERATE ON-SCREEN MENU You can control and adjust this projector through ON-SCREEN WIRELESS REMOTE CONTROL FOCUS MENU. Refer to following pages to operate each adjustment on ON-SCREEN MENU. MENU BUTTON 1 DISPLAY MENU POINT BUTTON Press MENU button to display ON-SCREEN MENU. Used to move Pointer UP/ DOWN/ RIGHT/ SELECT LEFT. 2 MOVING POINTER Move pointer (✽ see below) or adjust value of item by pressing SELECT BUTTON POINT button(s)
