ページ1に含まれる内容の要旨
Liquid Crystal Projector
Model
28A8800A
OPERATING GUIDE
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Liquid Crystal Projector Model ImagePro 8800A USER’S GUIDE Thank you for purchasing the Dukane liquid crystal projector. Please read this user’s manual thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. Page Contents Outline Before Use ............................................. 3 Checking the package Contents .............8 This liquid crystal projector is used to project Names and functions of each pa
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
Before Use About the Symbols Various symbols are used in this instruction manual and on the product itself to ensure correct usage, to prevent danger to the user and others, and to prevent property damage. The meanings of these symbols are described below. It is important that you read these descriptions thoroughly and fully understand the contents. This symbol indicates information that, if ignored, could possibly Warning result in personal injury or even death due to incorrect h
ページ6に含まれる内容の要旨
[Safety Precaution] Warning n If a problem should occur. n Do not insert foreign objects. If smoke or a strange odor arise, continued Do not insert metal objects through • • use could result in fire or electrical shock. In the ventilation openings, etc., of such case, immediately turn off the power this projector or drop such objects switch and then disconnect the power plug inside because this could result in from the power outlet. After making sure that fire or electrical shock. the smoke or o
ページ7に含まれる内容の要旨
Warning n Handle the power cord with care. n High temperatures are generated when Do not damage, cut, process or • the lamp is lit, so do not place objects in strongly twist the power cord. Placing front of the lens. heavy objects on the power cord, heating or strongly pulling the power cord can result in damage as well as fire or electrical shock. • Pulling on the power cord • Placing heavy objects on the power cord • Damaging the cord • Placing near heaters Do not position the power • cord und
ページ8に含まれる内容の要旨
Caution n Do not sit or place heavy objects on n Clean the projector interior once this projector. every two years. Do not sit on this projector. Request your dealer to clean the interior • This could result in overturning, of the projector approximately every two leading to damage or personal injury. years. Accumulations of dust inside the Use special caution in households projector can result in fire or where children are present. malfunction if not cleaned for an Do not place heavy objects on
ページ9に含まれる内容の要旨
Caution n When the projector is not to be used n Moving the projector. When moving the projector, be sure for an extended period. • to close the lens cover, disconnect For safety purposes when the the power plug from the power outlet projector is not to be used for an Disconnect the and disconnect all external extended period because of travel, plug from the Disconnect the connections. Failure to do this etc., always disconnect the power power outlet. plug from the could damage the power cord pl
ページ10に含まれる内容の要旨
Checking the package Contents Make sure all of the following items are included in the package. If anything is missing, please contact your VIDEO RGB dealer. LASER STANDBY/ON POSITION RESET MENU FREEZE MAGNIFY VOLUME OFF Remote control Projector unit Remote control Batteries User’s Guide (this document) Power Cord 3-Conductor c d 110V-US video/Audio cable 220-UK, Europe RGB cable Mac adapter Mouse cable ´ 3 (15-15 pin M/M) with dip switch Names and functions of each part Main unit FOCUS button Z
ページ11に含まれる内容の要旨
Names and functions of each part (continued) Remote control photoreceptor Main power switch Used to turn the power on and off. : OFF : ON AC IN jack Used to connect the accessory power cord. VIDEO IN jack Caution Connecting to the AC IN jack S-VIDEO IN jack Make sure the accesory power cord is plugged into Mini DIN 4-pin connector the AC IN jack as far as it will go. Incomplete VIDEO IN jack RCA jack connection can result in fire or electrical shock. AUDIO L/R IN jack RCA jack 12 RGB IN S-VIDEO
ページ12に含まれる内容の要旨
Names and functions of each part (continued) Remote control transmitter VIDEO, RGB button LASER button Press to switch the input. (Refer to page 13, 19.) VIDEO RGB Turns the laser beam on and off. Refer to page LASER 11 cocnerning usage and observe the cautions. STANDBY/ON POSITION STANDBY / ON button POSITION button ** Used to turn the power on and off. Pressing the top, bottom, left or right of Disk Pad after Press for 1 sec. or more to turn the power off pressing this button causes correspond
ページ13に含まれる内容の要旨
Names and functions of each part (continued) Loading the batteries Loading AA batteries into the remote control. 1 Remove the battery 2 Loading the batteries. Make sure the plus and cover. minus poles are correctly Push the knob while oriented. lifting up the battery cover. 3 Close the battery cover. Caution Battery usage cautions Caution Remote control usage cautions Use only the specified batteries with this Do not drop the remote control or apply impact. • • projector. Also, do not mi
ページ14に含まれる内容の要旨
Installation Typical LCD Projector and Screen Installation Use the diagram below as reference to determine the screen size and projection distnace. Top view Side view Screen Lens center b a a. Distance from the LCD projector to the screen a a (inches) b.Distance from the lens center to the bottom of Screen size (inches) b (inches) Minimum Maximum the screen (a,b : +/-10%). 40 55 73 1 Caution 60 85 114 2 The LCD projector should normally be used level (the legs can point upward). 80 114 151 2 Pos
ページ15に含まれる内容の要旨
Basic operations VIDEO RGB To project LASER STANDBY/ON POSITION 2 7 2 5 7 4 RESET MENU FREEZE MAGNIFY VOLUME OFF P in P MUTE BLANK AUTO TIMER 5 4 FOCUS ZOOM 1 3 Turn on the main power switch of the projector [ I: ON]. 1 • The Power indicator lights orange. Press the STANDBY / ON button. 2 • The Power indicator will blink green and then light green. • The green blinking indicates warmup. • After the power is turned on, the lamp will be cooled for approximately 1 min. and the power cannot be turne
ページ16に含まれる内容の要旨
Basic operations (continued) Turning off the power VIDEO RGB LASER 1 STANDBY/ON POSITION 1 RESET MENU FREEZE 2 MAGNIFY VOLUME OFF P in P MUTE 3 BLANK AUTO TIMER Press the STANDBY/ON button for approximately 1 sec. 1 • The Power indicator will blink orange, then the lamp will turn off. Approximately 1 sec. after that, the lamp will light orange. • After the power is turned off, the lamp will be cooled for approximately 1 min. and the power cannot be turned off even by pressing the STANDBY/ON butt
ページ17に含まれる内容の要旨
Basic operations (continued) Freeze function VIDEO RGB This function is used to freeze the image being displayed. LASER (refer to page 10) STANDBY/ON POSITION RESET MENU FREEZE MAGNIFY VOLUME OFF 1 P in P MUTE BLANK AUTO TIMER Press the FREEZE button. 1 • The image being displayed will freeze. • The [ ] mark appears in the lower right corner of the screen when the Freeze function is on. Cancelling the FREEZE function Press the FREEZE button. 1 • The FREEZE function will be cancelled. • The [
ページ18に含まれる内容の要旨
Basic operations (continued) VIDEO RGB LASER Magnify function STANDBY/ON POSITION 4 Part of an image can be displayed magnified. (refer to page 10) 5 RESET MENU 1,2 FREEZE 6 MAGNIFY VOLUME OFF 3 P in P MUTE BLANK AUTO TIMER Press the MAGNIFY + button. 1 • The center part of the image will be displayed magnified approximately two times. Changing the magnification ratio Press the MAGNIFY + button. 2 • When this button is pressed, the image will be displayed even larger. Press the MAGNIFY – button
ページ19に含まれる内容の要旨
Adjustments and functions VIDEO RGB LASER STANDBY/ON POSITION 1, 2, 3 2, 3 RESET MENU FREEZE MAGNIFY VOLUME OFF MENU 3 P in P MUTE BLANK AUTO TIMER 1 FOCUS ZOOM 1, 3 Press the MENU ( ) buttons of the projector or the 1 MENU button of the remote control. • The Menu screen will appear. (refer to page 18 - 21 for details.) Press the MENU ( ) buttons of the projector or the 2 DISK PAD button of the remote control to select the menu item to be adjusted. • The selected menu i
ページ20に含まれる内容の要旨
Adjustments and functions (continued) SET UP Images and display positions can be adjusted from the SETUP menu. Video signal input RGB signal input SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. VOLUME VOLUME BRIGHT BRIGHT CONTRAST CONTRAST V POSIT 100 SHARPNESS H POSIT 100 COLOR H PHASE TINT H SIZE 800 COLOR BAL R COLOR BAL R COLOR BAL B COLOR BAL B Adjustment item Adjustment description VOLUME Volume decreases Volume increases BRIGHT Darker Brighter (BRIGHTNESS) CONTRAST Lower contrast
