ページ1に含まれる内容の要旨
4-205-772-13 (1)
R
Digital
Projection TV
GB
Instruction Manual
KP-51DS1U
KP-51DS2U
©2002 by Sony Corporation
ページ2に含まれる内容の要旨
NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS 1362 (i.e. marked with 2 or @) must be used. When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit should be protected by a 5 AMP FUSE at the distribution board. If the plug supplied with this e
ページ3に含まれる内容の要旨
p Introduction Thank you for choosing this Sony Projection TV. Before operating the projection TV, please read this manual thoroughly and retain it for future reference. • Symbols used in the manual: MENU K • Important information. • Shaded buttons on the remote control show the buttons you have to press to follow the sequence • Information on a feature. of instructions. • 1,2... Sequence of instructions. • Informs you of the result of the instructions. Table of
ページ4に含まれる内容の要旨
Safety Information Safety Information Never push objects of any kind into the set as For environmental and safety reasons, it is this could result in a fire or electric shock. This set is to operate on a 220-240V AC supply recommended that the TV set is not left in Never spill liquid of any kind on the set. If only. Take care not to connect too many standby mode when not in use. Disconnect any liquid or solid object does fall into the appliances to the same power socket as this
ページ5に含まれる内容の要旨
Overview Checking the Accessories Supplied s Two batteries (R6 type) One Remote Control (RM-892) GB Overview of Projection TV Buttons (conectores lado izquierdo) (conectores lado derecho) (right side connectors) (left side connectors) On/Off Switch Programme up or down buttons Standby S Video (selects TV channels) indicator Input jack Volume control Video Input buttons jack Auto Convergence Selecting Audio Input button input source jacks Headphone jack Press on the mark , on the fr
ページ6に含まれる内容の要旨
Getting Started - Overview Overview of Remote Control Buttons Displaying the time Press to switch the time on or off (available only when analogue teletext is VIDEO TV broadcast). VIDEO TV VCR operation This button does not work on this set. For more details, please refer to the section "Remote Control of other Sony VTR 1 2 3 4 DVD Equipment" VTR 1 2 3 4 DVD CH CH Muting the Sound To Temporarily Switch Off projection TV Press to m
ページ7に含まれる内容の要旨
Installation Inserting Batteries into the Remote Control Make sure you insert the batteries using the correct polarities. Always remember to dispose of used batteries in an environmental friendly way. Connecting the Aerial and VCR Connecting cables are not supplied. GB OUT IN VCR Scart lead (optional) The Scart lead is optional. If you use this optional connection it can improve picture and sound quality when using a VCR. If you do not use a SCART lead, after automatically tuning th
ページ8に含まれる内容の要旨
First Time Operation Switching on the Projection TV and Automatically Tuning The first time you switch on your TV, a sequence of menu screen appear on the TV enabling you to 1) choose the language of the menu screen, 2) search and stores all available channels (TV Broadcast) and 3) change the order in which the channels (TV Broadcast) appear on the screen. However, if you need to change the language menu, change the country, change or repeat the tuning (e.g. wh
ページ9に含まれる内容の要旨
OK First Time Operation 5 After all available channels are captured and stored, the Programme Sorting menu appears automatically on the screen PROGRAMME SORTING VIDE TV PROG SYS CHAN LABEL enabling you to change the order in which the channels appear 0 DIG C 28 BBC-W 1 DIG C 40 MV-CH on the screen. 2 DIG C 41 TVE-1 3 DIG C 31 TVE-2 4 DIG C 34 ANT-3 a) If you do not wish to change the channel order, go to step 6. 5 DIG C 27 TELE 5 6 DIG C 47 C PLUS 7 DIG C 44 - - - - - 8 DIG C 23 - -
ページ10に含まれる内容の要旨
Menu System Adjusting Colour Registration (Convergence) Due to the earth’s magnetism, the picture might become undefined and you could see different colours on the outlines of the images. In that case, proceed as follows: Auto converge the Red, Green, and Blue Lines 1 Press on the mark , on the front of the projection TV to reveal the front connectors. 2 Press button on the projection TV. The Auto Convergence function works for about 30 seconds. When the white cross disappears from the scre
ページ11に含まれる内容の要旨
Menu System Adjusting the Picture Although the picture is adjusted at the factory, you can modify it to suit your own taste. PICTURE CONTROL 1 Press the MENU button on the remote control to display the menu VIDEO TV on the screen. Picture Mode Personal Contrast Reset Format Wide Digital Signal Composite 2 Push the joystick to z to enter the PICTURE CONTROL menu. 3 Push the joystick to $ or 4 to select the item you wish to change, then push to z. PICTURE CONTROL Refer to the table below to
ページ12に含まれる内容の要旨
Menu System Changing the screen mode Using this Screen Mode feature you can change the aspect ratio of the screen. PICTURE CONTROL 1 Press the MENU button on the remote control to display the menu VIDEO TV VIDEO TV on the screen. Picture Mode Personal Contrast Reset Format Wide Digital Signal Composite 2 Push the joystick to z button to enter the PICTURE CONTROL menu. PICTURE CONTROL 3 Push the joystick to $ to select Format, then push to z. Picture Mode Personal Contrast Reset Format Wide
ページ13に含まれる内容の要旨
Menu System Adjusting the Sound Although the sound is adjusted at the factory, you can modify it to suit your own taste. PICTURE CONTROL 1 Press the MENU button on the remote control to display the menu VIDEO TV on the screen. Picture Mode Personal Contrast Reset Format Wide Digital Signal Composite 2 Push the joystick to $ to select the symbol, then push to z to enter to the SOUND CONTROL menu. 3 Push the joystick to $ or 4 to select the item you wish to change, then push to z. SOUND C
ページ14に含まれる内容の要旨
Menu System 4 Push the joystick to Z or z to alter the selected item, then press the VIDEO TV OK button to store the new adjustment. 5 Repeat steps 3 and 4 to Salter the other items. 6 Press the MENU button to exit and return to the normal TV screen. 1 2 3 4 5 6 7 8 9 0 Changing Sound Mode Quickly You can quickly change Sound mode without entering the Sound Control menu screen. 1 Press the button on the remote control to directly access to the PROGR Sound Mode. MENU Personal 2 Push the joy
ページ15に含まれる内容の要旨
Menu System Using the Sleep Timer You can select a time period for the TV to switch itself automatically into the standby mode. PICTURE CONTROL 1 Press the MENU button on the remote control to display the menu VIDEO TV Picture Mode Personal on the screen. Contrast Reset Format Wide Digital Signal Composite TIMER 2 Push the joystick to $ button to select the t symbol, then push to z Sleep Timer Off to enter to the TIMER menu. 1 2 3 4 5 6 TIMER 7 8 9 3 Push the joystick to z, then push to Z
ページ16に含まれる内容の要旨
Menu System Manually Tuning the TV Use this function to preset channels or a video input source one by one to the programme order of your choice. PICTURE CONTROL 1 Press the MENU button on the remote control to display the menu on VIDEO TV VIDEO TV Picture Mode Personal the screen. Contrast Reset Format Wide Digital Signal Composite PRESET 2 Push the joystick to $ to select the symbol, then push to z to enter Auto Programme to the PRESET menu. Manual Programme Preset Further Programme Pres
ページ17に含まれる内容の要旨
Menu System Using the "Further Programme Preset" function With this feature you can: a) Even normally the automatic fine tuning (AFT) is operating, however you can manually fine-tune the TV (only available on analogue channels) to obtain a better picture reception if the picture is distorted or b) preset the AV3 output for the programme positions of channels with scrambled signals (eg from a pay TV decoder). In this way a connected VCR records the unscrambled signal. PICTURE CONTROL 1 Press t
ページ18に含まれる内容の要旨
Menu System Locking Programmes This feature enables you to prevent undesirable broadcasts appearing on the screen. We suggest you use this function to prevent children from watching programmes you consider unsuitable. PICTURE CONTROL 1 Press the MENU button on the remote control to display the menu VIDEO TV Picture Mode Personal on the screen. Contrast Reset Format Wide Digital Signal Composite PRESET 2 Push the joystick to $ to select the symbol, then push to z to enter Auto Programme to th
ページ19に含まれる内容の要旨
Menu System Skipping Programme positions You can programme this projection TV to skip any unwanted programme numbers when they are selected with the PROGR +/- buttons. To cancel this function afterwards, proceed in the same way as described below by selecting the appropriate TV system (I or DIG) instead of "- - -" in step 5. PICTURE CONTROL 1 Press the MENU button on the remote control to display the menu VIDEO TV Picture Mode Personal on the screen. Contrast Reset Format Wide Digital Signal
ページ20に含まれる内容の要旨
Menu System Labelling a channel (analogue channels only) Names for analogue channels (TV Broadcasts) are usually taken automatically from Teletext if available. You can however name a channel or an input video source using up to five characters (letters or numbers). Using this function, you can easily identify which channel (TV Broadcasts) or video source you are watching. PICTURE CONTROL 1 Press the MENU button on the remote control to display the menu on VIDEO TV VIDEO TV Picture Mode Per
