ページ1に含まれる内容の要旨
¡
MICROLINE 3320/3321
PRINTER
Maintenance Manual
All specifications are subject to change without notice.
ページ2に含まれる内容の要旨
PREFACE This maintenance manual describes how to maintain the Microline 3320/3321 printer in the field. This manual is for customer engineers. For further information, refer to the Users Manual for handling or operating the equipment. iii
ページ3に含まれる内容の要旨
TABLE OF CONTENTS 1. CONFIGURATION 1.1 Standard Printer Configuration 1.2 Options 2. THEORY OF OPERATION 2.1 Electrical Operation 2.1.1 Summary 2.1.2 Microprocessor and the Peripheral Circuit 2.1.3 Initialization 2.1.4 Parallel Interface Control 2.1.5 Print Control 2.1.6 SP/LF Motor Control 2.1.7 Operation Panel 2.1.8 Alarm Circuit 2.1.9 Power Supply Circuit 2.2 Mechanical Operation 2.2.1 Printhead Mechanism and Operation 2.2.2 Spacing Operation 2.2.3 Head Gap Adjusting 2.2.4 Ribbon Drive 2.2.5
ページ4に含まれる内容の要旨
3.3.9 Carriage Cable 3.3.10 Backup Roller Holder Assy 3.3.11 Platen Assy 3.3.12 Driver Board (SDDV) 3.3.13 LF Motor 3.3.14 Operation Panel PCB (LEOP) 3.3.15 Control/Power Supply Board (SDCT) 3.3.16 Transformer Assy 3.3.17 Change Lever and Gears 3.3.18 Carriage Shaft 3.3.19 Paper Pan 3.3.20 Rear Tractor Assy 3.3.21 Rear Pressure Assy 3.3.22 Switch Lever 4. ADJUSTMENT 5. CLEANING AND LUBRICATION 5.1 Cleaning 5.2 Lubrication 6. TROUBLESHOOTING AND REPAIR 6.1 Items to Check Before Repair 6.2 Trouble
ページ5に含まれる内容の要旨
1. CONFIGURATION
ページ6に含まれる内容の要旨
1. CONFIGURATION 1.1. Standard Printer Configuration This printer consists of the following assemblies: Sheet guide assy Platen knob Access cover assy Upper cover Transformer assy Pull-up roller assy Control/Power supply assy Driver board Operation panel assy Main chassis assy Figure 1-1 Configuration 1 – 1
ページ7に含まれる内容の要旨
1.2 Options (1) Cut sheet feeder unit (CSF) (Narrow and wide versions available) Dual-bin CSF Single-bin CSF Attachment assy (2) Pull-tractor assy 1 – 2
ページ8に含まれる内容の要旨
(3) Bottom push tractor unit (4) Roll paper stand (Narrow only) (5) Serial I/F • RS232C • RS422A • Current Loop 1 – 3
ページ9に含まれる内容の要旨
2. THEORY OF OPERATION
ページ10に含まれる内容の要旨
2. THEORY OF OPERATION 2.1 Electrical Operation The electrical operation of the printer circuit is described in this section. 2.1.1 Summary Fig. 2-1 shows the block diagram of the printer. The control board is made up of the microprocessors, peripheral circuits, drive circuits, sensors and interface connectors. The power to the control board is supplied by the power board through the connector cord. The power to other electrical parts is also distributed through the connectors within the control
ページ11に含まれる内容の要旨
2 – 2 (opt.) AD-BUS 67 x 640 CSF LSI ADDRESS Roll paper Stand ROM DRAM 12.288 MHz (opt.) 4*64 Para 1M RS232C Kbit*2 -I/F max -I/F 4M 4 AI TSD Vcc-Level EEPROM TSD Head 1 Kbits AUTO-LF driver I/F-IPT HD-Alarm Print-IPT 2P Encoder INT Release-SW Bottom-Sensor SP M SP PE-SENSOR driver Serial SP alarm OPERATION PANEL LF M LF driver Fuse Power-off 40 volt Rectifier Alarm HD-Alarm 40 V 8 volt circuit circuit SP-Alarm 5 volt RESET Reset 5VD circuit Divider Vcc-Level AC-input Transformer Figure 2-1
ページ12に含まれる内容の要旨
(2) Program ROM This is a 256 × 16 bits (4M bit) [MAX] EPROM with the control program for the printer stored. The MPU executes instructions under this program. The program ROM is assigned to the program memory area of the MPU and is fetched by the PSEN signal of the MPU. The following shows the operation of the memory access. MPU ROM A0~A17 D0~D15 PG-N CSO CE PSEN OE MPU CLOCK A0~A17 PG-N PSEN-N Program Program Program D0~D15 IN IN IN 2 – 3
ページ13に含まれる内容の要旨
(3) RAM (MSM51C464A-80RS) The RAM is CMOS dynamic RAM with (64K × 4-bit) × 2 configuration, and used as buffers (such as receiving buffer, printing buffer, DLL buffer and working buffer). The following shows the examples of the memory access operation. MPU
RAM 1 (Q3)
A0~A7
RAM 2 (Q4)
P03
RAS
CS1
CAS
D0~D3
D4~D7
RD
OE
Clockout*
T1
T2
T3
A0~A7
CS1~CS4
RD
D0~D7
(Read)
WRH
WRL
D0~D7
(Write)
8-bit bus, byte instruction
* Clockout is provided when the original excitation is s
ページ14に含まれる内容の要旨
(4) EEPROM The EEPROM is a CMOS serial I/O type memory which is capable of electrically erasing and writing 1,024 bits. The EEPROM contains menu data. The following shows the memory access operation. MPU EEPROM EEDIN-P P24 D1 EECS-P P27 CS EEDOUT-P DO P25 EECLK-P SK P26 PRE = O PE = X EECS-P t CS EECLK-P Operation Start code Address code 0 1 1 EEDIN-P A5 A0 0 EEDOUT-P D15 D0 D15 D0 D15 Read cycle timing (READ) PRE = O PE t CS EECS-P EECLK-P Operation Start Address Data
ページ15に含まれる内容の要旨
(5) LSI This LSI detects and controls the SP motor speeds by monitoring the two phase sensor signals obtained from the DC motors and modifying the excitation phases as appropriate. This LSI is connected in multiplex to the MPU. MPU LSI A/D bus P07 ALE RD RDN WRL WRL P01 LSIC Clockout* A0~A19 LSICS ALE D0~D15 Address Data (Read) RD D0~D15 Address Data (Write) WRL * Clockout is provided when the original excitation is selected. 2 – 6
ページ16に含まれる内容の要旨
2.1.3 Initialization This printer is initialized when the power is turned on or when the I-PRIME-N signal is input from the host side via the parallel interface. For the initialize operation, the RST-N signal is first output from the reset circuit to reset the MPUs and LSIs. When resetting ends, the program starts and the LSIs are reset by MPU via LSIRST-N. Reset operation by I-PRIME starts program to initialize, but does not reset the MPU. The program here sets the mode of the LSI including the
ページ17に含まれる内容の要旨
2.1.4 Parallel Interface Control The parallel data input from the host to the interfaced LSI is latched to its internal register at the falling edge of the STROBE-N signal. At the same time, the LSI sets the BUSY signal to the high level to inform the host that the data is being processed, and outputs the RXD signal to inform the MPU of data reception. The data is read upon receiving the RD-N signal from the MPU. When the data processing ends, the BUSY signal is set to off and the ACK-N signal i
ページ18に含まれる内容の要旨
2.1.5 Print Control Print data is transmitted as parallel data (HEAD1~HEAD9) from LSI to print head. LSI generates print timing and drive time. Control/Power Supply Board
Driver Board
MPU
LSI
A/D bus
DRIVER
Print Head
Print Data
Print Data
HEAD1-N~
HEAD1~
HEAD9-N
HEAD9
HEAD DRIVE TIMING CHART DT1 DT2 HEAD DRIVE CURRENT 2 – 9
ページ19に含まれる内容の要旨
Print Compensation Control The print compensation can be made as shown below: (a) Voltage compensation (See 2.1.8 “Alarm Circuit.”) (b) Temperature compensation (See 2.1.8 “Alarm Circuit.”) (c) Pin stroke compensation Platen
Print Head
Pin 1, 2
As shown in the drawing left, the stroke length up to the platen is different for each pin. 3~6
8, 9
Pin coil
current
Pin 1, 2,
8, 9
Pin 3~6
Time
(d) Simultaneous Compensation of the number of impact pins The MPU is provided with the compensat
ページ20に含まれる内容の要旨
(e) Print mode compensation According to the thickness of the printing medium, the print mode is compensated as shown in the table below: Head Gap Range 1 2 3 4 5 Print speed 100% 95% 85% 85% 80% Drive time Short Long (Drive time lengthens at each step.) 2 – 11
