ページ1に含まれる内容の要旨
TOSHIBA Potable Printer
B-EP4DL SERIES
Maintenance Manual
Document No. EO18-33023
Original Sep., 2008
(Revised )
PRINTED IN JAPAN
ページ2に含まれる内容の要旨
WARNING! Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution. NOTE: Failure to follow manual instructions or any unauthorized modification, substitution orchange to this product will void the limited product warranty.
ページ3に含まれる内容の要旨
EO18-33023 (Revision Date: Dec. 16, 2008) TABLE OF CONTENTS Page 1. UNPACKING .............................................................................................................. 1- 1 1.1 Procedure........................................................................................................................1- 1 1.2 Checks.............................................................................................................................1- 1 2. MAJOR UNIT RE
ページ4に含まれる内容の要旨
1. UNPACKING EO18-33023 1.1 Procedure 1. UNPACKING 1.1 Procedure 1) Open the carton. 2) Unpack the accessories from the carton. 3) Unpack the printer. NOTE: Keep the carton and pad for future transportation of the printer. 1.2 Checks 1) Check for damage or scratches on the machine. 2) Confirm that none of the accessories are missing. 1- 1
ページ5に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 2.1 Replacing the CPU PC Board 2. MAJOR UNIT REPLACEMENT WARNING! 1. Disconnect the power cord before installing the main parts. 2. Be careful not to injure your fingers when replacing the main parts. CAUTION! 1. Since a lot of small moulded parts are used in this printer, care must be taken not to damage or lose them. 2. Be careful not to damage the print head while removing and reassembling. 3. In the United States, used lithium ion batteries
ページ6に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 2.1 Replacing the CPU PC Board 4) Press the Top Cover Open Button to open the Top Cover. 5) Remove the Left Side Cover in the direction of the arrow. Top Cover Top Cover Open Button Left Side Cover NOTE: The Gears shown in the picture below are not secured and are easily removed. Be careful not to drop and break or lose them. Gear 6) Remove the Right Side Cover and the Front
ページ7に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 2.1 Replacing the CPU PC Board 7) Remove the Front Cover. CPU PC Board Front Cover 6) Disconnect all Connectors and FPC Cable from the CPU PC Board. NOTE: Before disconnecting the FPC Cable, release the Connector Lock. FPC Cable CPU PC Board Connector Lock 7) Disconnect the Earth Terminal from the Drive PC Board. Drive PC Board Earth Terminal 2-3
ページ8に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 2.1 Replacing the CPU PC Board 8) Open the Hooks, then remove the CPU PC Board from the Front Cover. CPU PC Board Hook Hook 9) Remove the screw, then remove the Earth Terminal. T-2x5 Screw Earth Terminal 10) Replace the CPU PC Board with a new one, then reassemble in the reverse order of removal. 2-4
ページ9に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 2.1 Replacing the CPU PC Board 11) Close the front cover. Front Cover NOTES: 1. Make sure that the pins on the both sides of the front cover are fit in position, as shown in the pictures below. Pin 2. Do not reassemble the Front Cover while the Top Cover Open Button is pressed. Doing so may cause the Top Cover not to open. No Good Good Top Cover Ope
ページ10に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 (Revision Date: Dec. 16, 2008) 2.1 Replacing the CPU PC Board NOTE: It is easy to mount the left side cover if you fit the tabs from the LCD side in order, then secure the bottom side. Be careful not to catch the cable by the cover while reassembling. Left Side Cover 13) Mount the right side cover to the printer while fitting the tabs on the right side cover into the slots of the printer enclosure. Fit t
ページ11に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 (Revision Date: Dec. 16, 2008) 2.1 Replacing the CPU PC Board NOTES: 1. After replacing the CPU PC Board, refer to the Setting Operation Manual or System Mode Manual and perform the following operations. 1. Perform a RAM clear. 2. Perform the sensor adjustment. 2. After replacing the CPU PC Board, perform an LED check in the system mode and make sure the LED lights properly. If the LED does not light properly, this may result from
ページ12に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 2.2 Replacing the LCD Unit 2.2 Replacing the LCD Unit 1) Remove the Right Cover, Left Cover, Front Cover and CPU PC Board. (Refer to Section 2.1 Replacing the CPU PC Board.) 2) Remove the three screws, then remove the LCD Unit. T-2x5 Screw Screw LCD Unit 3) Replace the LCD Unit with a new one, then reassemble in the reverse order of removal. 4) After replacing the LCD unit, perform an LCD check in
ページ13に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 2.3 Replacing the Peel-off Roller 2.3 Replacing the Peel-off Roller 1) Remove the Right Cover, Left Cover and Front Cover. (Refer to Section 2.1 Replacing the CPU PC Board.) 2) Remove the two Roller Clips with a straight slot screwdriver, then remove the Peel-off Roller Ass’y. Roller Clip Straight Slot Peel-off Roller Screwdriver Roller Clip 3) Remove the two Peel-off Rollers and the two Roller Clips from the Roller Shaf
ページ14に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 2.4 Replacing the Peel-off Sensor 2.4 Replacing the Peel-off Sensor 1) Remove the Right Cover, Left Cover and Front Cover. (Refer to Section 2.1 Replacing the CPU PC Board.) 2) Disconnect the Connector from the CPU PC Board. 3) Pull out the Cover Shaft, then remove the Peel-off Sensor Unit. CPU PC Board Connector Cover Shaft Peel-off Sensor Unit Peel Off Sensor Unit 4) Release the Peel-off Sensor Cover from the Hooks
ページ15に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 2.4 Replacing the Peel-off Sensor 6) Replace the Peel-off Sensor with a new one, then reassemble in the reverse order of removal. NOTES: 1.Be careful of the orientation of the Peel-off Springs as shown in the picture below when reassembling the Peel-off Sensor Unit. Peel-off Spring R Peel-off Spring L Peel-off Sensor Unit 2. After replacing the Peel-off Sen
ページ16に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 2.5 Replacing the Drive PC Board 2.5 Replacing the Drive PC Board 1) Remove the Right Cover, Left Cover and Front Cover. (Refer to Section 2.1 Replacing the CPU PC Board.) 2) Disconnect all Connectors and FPC Cable from the Drive PC Board. Drive PC Board Drive PC Board NOTE: Before disconnecting the FPC Cable, release the Connector Lock. FPC Cable Connector Lock 3) Remove the Drive PC Board from
ページ17に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 2.6 Replacing the Battery Terminal 2.6 Replacing the Battery Terminal 1) Remove the Right Cover, Left Cover and Front Cover. (Refer to Section 2.1 Replacing the CPU PC Board.) 2) Remove the Drive PC Board. (Refer to Section 2.5 Replacing the Drive PC Board.) 3) Hold down the Hook and remove the Battery Terminal upward. Hook Battery Terminal 4) Replace the Battery Terminal with a new one, then reassemble in the rever
ページ18に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 2.7 Replacing the Stepping Motor 2.7 Replacing the Stepping Motor 1) Remove the Right Cover, Left Cover and Front Cover. (Refer to Section 2.1 Replacing the CPU PC Board.) 2) Remove the two screws. Stepping Motor SMW-3x8 Screw 3) Disconnect the Connector from the Drive PC Board. 4) Remove the Stepping Motor. Stepping Motor Connector Drive PC Board Replace the Stepping Motor with a
ページ19に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 2.9 Replacing the Cover Open Switch and Media Sensor (Lower) 2.8 Replacing the Print Head CAUTION! 1. Before handling the print head, be sure to discharge static electricity in human body through other metals. Failure to do this may damage the print head element. 2. Never touch the print head element directly by hands or hard objects. Doing so will damage the element, causing a dot missing and a print failure. 1) Remove the Right Cover
ページ20に含まれる内容の要旨
2. MAJOR UNIT REPLACEMENT EO18-33023 (Revision Date: Dec. 16, 2008) 2.9 Replacing the Cover Open Switch and Media Sensor (Lower) 5) Disconnect the Head FPC from the Print Head Connector. NOTE: When reassembling the Head FPC, the contact portion should be faced upward. Print Head Connector Head FPC 6) Remove the Print Head Ass’y. 7) Disconnect the Head FPC Cable from the Drive PC Board Connector. Drive PC Board Head
