ページ1に含まれる内容の要旨
LASER PRINTER
(Multi-function printer)
Operation Manual
for printer operation and general information on multi functions
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
INSTALLATION REQUIREMENTS Improper installation may damage this product. Please note the following during initial installation and whenever the machine is moved. 1. The machine should be installed near an accessible power outlet for easy connection. 2. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded. ● For the power supply requirements, see the name plate of the main unit. 3. Do
ページ4に含まれる内容の要旨
CAUTIONS 1. Do not touch the photoconductive drum. Scratches or smudges on the drum will cause dirty printouts. 2. The fusing unit is extremely hot. Exercise care in this area. 3. Do not look directly at the light source of a scanner module. Doing so may damage your eyes. Fusing unit 4. Five installation adjusters are provided on a stand/ paper drawer which is provided as a peripheral unit. When moving the machine with a stand/paper drawer, be sure to raise the installation adjusters. After mov
ページ5に含まれる内容の要旨
CAUTIONS Cautions on laser Wave length 785 nm ± 15 nm Pulse times North America: (4.0 μs ± 4 ns)/7 mm Europe: (5.4 μs ± 5.4 ns)/7 mm Output power 0.25 mW - 0.50 mW At the production line, the output power of the scanner unit is adjusted to 0.6 MILLIWATT PLUS 8 PCTS and is maintained constant by the operation of the Automatic Power Control (APC). Caution This product contains a low power laser device. To ensure continued safety do not remove any cover or attempt to gain access to the inside of th
ページ6に含まれる内容の要旨
CAUTIONS For Europe: CAUTION VAROITUS! INVISIBLE LASER RADIATION LAITTEEN KÄYTTÄMINEN WHEN OPEN INTERLOCKS MUULLA KUIN TÄSSÄ CLASS 1 LASER PRODUCT DEFEATED. AVOID EXPOSURE KÄYTTÖOHJEESSA TO BEAM. MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN VORSICHT LASER KLASSE 1 TURVALLISUUSLUOKAN 1 UNSICHTBARE YLITTÄVÄLLE LASERSTRAHLUNG WENN NÄKYMÄTTÖMÄLLE ABDECKUNG GEÖFFNET UND LUOKAN 1 LASERLAITE LASERSÄTEILYLLE. SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM VARNING STRAHL AUSSETZEN. KLASS 1 L
ページ7に含まれる内容の要旨
FACSIMILE FEATURE When using this product as a facsimile by installing a facsimile expansion kit as a peripheral unit, refer to the following items for proper use. For the description of use of the facsimile feature, see the facsimile operation manual supplied with the facsimile expansion kit. Line connector ■■■■■ Line connection For connection between this product and telephone line, be sure to use the supplied connection cable. Connect the connecting cable so that the terminal near the core is
ページ8に含まれる内容の要旨
CONTENTS Page INSTALLING PRINTER DRIVERS USING THE PLUG & PLAY FUNCTION OR INSTALLATION REQUIREMENTS . . . . . . . . . . . . 0-1 ADD PRINTER WIZARD . . . . . . . . . . . . . . . . . . . . . . . CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-2 ● Before installation CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-5 SETTING THE PRINTER DRIVER . . . . . . . . . . . . . . . ● Setting print conditions under Windows CHAPTER 1 (selecting and setting prin
ページ9に含まれる内容の要旨
CONTENTS CHAPTER 4 CHAPTER 6 TROUBLESHOOTING AND KEY OPERATOR PROGRAMS MAINTENANCE KEY OPERATOR PROGRAMS . . . . . . . . . . . . . . . . . . MISFEED REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . ● Key operator program list . . . . . . . . . . . . . . . . . . . . MACHINE TROUBLE? . . . . . . . . . . . . . . . . . . . . . . . . ● Using the key operator programs . . . . . . . . . . . . . . USER MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . ● Details of classification
ページ10に含まれる内容の要旨
ページ11に含まれる内容の要旨
CHAPTER 1 BEFORE USING THE PRODUCT This chapter describes basic information that should be read before using this product. Be sure to read this chapter before using this product. Page INTRODUCTION ................................................................................... 1-2 MAIN FEATURES .................................................................................. 1-5 PART NAMES AND FUNCTIONS ......................................................... 1-6 Exterior ................
ページ12に含まれる内容の要旨
INTRODUCTION Read this operation manual carefully to use this product properly. Be sure to read “INSTALLATION REQUIREMENTS” and “CAUTIONS” before using this product. Be sure to keep this operation manual handy to refer to it any time. This product is a multi-function printer that can be used as a local printer and a network printer as well as a copier, network scanner, and a facsimile by installing various types of peripheral units (optional). This operation manual describes the basic use of the
ページ13に含まれる内容の要旨
INTRODUCTION Abbreviated names of peripheral units The following unit is written with an abbreviated name without some exceptions to simplify the description in this manual. “B/W scanner module/DSPF” The unit is written as “scanner module”. 1 NOTES The scanner unit is a unit for scanning originals (automatic document feeder) when using the copier feature and facsimile feature. In the touch panel messages in the scanner module, the “scanner module” is displayed as “document feeder”. To use
ページ14に含まれる内容の要旨
INTRODUCTION The following table shows the relation between the various functions described in this manual, copier operation manual, facsimile operation manual, and network scanner operation manual and the required peripheral units. In each operation manual, the optional peripheral units that are required for using each function is not particularly described. Refer to this table as needed. = Must be installed *1 = Any of the units must be installed. *2 = Must be installed together with or *1.
ページ15に含まれる内容の要旨
MAIN FEATURES Multi-function printer allowing extension of functions based on the purpose This product is a multi-function printer that can be used as a local printer and a network printer as well as a copier, a network scanner, and a facsimile by combining peripheral units. Various optional units for improving productivity such as duplex modules for two-sided printing, additional paper feed units for large capacity paper stock, and paper output units for sorting printed sheets are provided as p
ページ16に含まれる内容の要旨
PART NAMES AND FUNCTIONS Exterior Bypass tray (part of duplex module/bypass tray)*1 Front cover Open to add toner and remove misfeeds. Exit tray*1 Main switch (See page xxxx.) Press to turn power on and off. Duplex module*1 Module for two-sided printing Paper tray 1 Upper paper output area Stand/3 x 500 sheet paper drawer*1 (See page Finished sheets are deposited here. xxxx.) Upper exit tray extension*1 Extension table for preventing dropping of large paper Stand/MPD & 2000 sheet paper drawer*1
ページ17に含まれる内容の要旨
PART NAMES AND FUNCTIONS Interior 1 Duplex module side cover Toner cartridge* (See page xxxx.) Open when a misfeed has occurred in the duplex Container that contains toner. When toner is module. exhausted, the cartridge must be removed and replaced with a new one. Side cover open knob Photoconductive drum Push up to open the side cover when a misfeed has occurred in the fusing unit. A photoconductor is applied to the surface of the photoconductive drum. Images are formed on the photoconductive d
ページ18に含まれる内容の要旨
PART NAMES AND FUNCTIONS Part names and functions of peripheral units 1-8
ページ19に含まれる内容の要旨
PART NAMES AND FUNCTIONS B/W scanner module/DSPF Multi purpose drawer 2 This unit is a monochrome scanner that allows Holds paper. Up to 500 sheets of 20 lbs. (80 g/m ) automatic feeding of sheet originals and continuous paper can be loaded. Also special papers such as scanning. The B/W scanner module/DSPF (Dual envelopes (standard sizes only) and Japanese Single Pass Feeder) can scan two-sided sheet postcard can be set. originals and can scan both sides at a time. Also a flat bed type document
ページ20に含まれる内容の要旨
PART NAMES AND FUNCTIONS Other peripheral units Scanner rack Hard disk drive Rack required for installing a scanner module. The Extends the image storing capacity for the printer height is fixed. and copier features (not for the facsimile feature). Also this unit is required for using the job retention function (see page xxxx) with which print data Power supply unit received for the printer feature is held temporarily For installation of some peripheral units, this unit is instead of imm
