ページ1に含まれる内容の要旨
Service Manual
Pi3505e
Pi3505e/PS
ページ2に含まれる内容の要旨
1. SAFETY PRECAUTIONS FOR INSPECTION AND SERVICE • When performing inspection and service procedures, observe the following precautions to prevent accidents and ensure utmost safety. ✽ Depending on the model, some of the precautions given in the following do not apply. Different markings are used to denote specific meanings as detailed below. WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a potentiall
ページ3に含まれる内容の要旨
WARNING 2. Before starting the procedures, be sure to unplug the power cord. This product contains a high-voltage unit and a circuit with a large current capacity that may cause an electric shock or burn. The product also contains parts that can jerk suddenly and cause injury. If this product uses a laser, laser beam leakage may cause eye damage or blindness. 3. Do not throw toner or the toner bottle into a fire. Do not throw toner or the Toner Bottle (Imaging Cartridge, Toner Cartrid
ページ4に含まれる内容の要旨
WARNING 8. Do not touch a high-temperature part. A part marked with the symbol shown on the left and other parts such as the exposure lamp and fusing roller can be very hot while the machine is ener- gized. Touching them may result in a burn. Wait until these parts have cooled down before replacing them or any sur- rounding parts. 9. Maintain a grounded connection at all times. Connect the power cord to an electrical outlet that is equipped with a grounding terminal. 10. Do not remodel
ページ5に含まれる内容の要旨
CAUTION 2. Precautions for Servicing with Covers and Parts Removed. Wherever feasible, keep all parts and covers mounted when energizing the product. If energizing the product with a cover removed is absolutely unavoidable, do not touch any exposed live parts and use care not to allow your clothing to be caught in the moving parts. Never leave a product in this condition unattended. Never place disassembled parts or a container of liquid on the product. Parts falling into, or the liqui
ページ6に含まれる内容の要旨
1-3. Used Batteries Precautions ALL Areas CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Germany VORSICHT! Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleichwertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. France ATTENTION I
ページ7に含まれる内容の要旨
1-4. Other Precautions When handling circuit boards, observe the “HANDLING of PWBs”. The PC Drum is a very delicate component. Observe the precautions given in “HAN- DLING OF THE PC DRUM” because mishandling may result in serious image problems. Note that replacement of a circuit board may call for readjustments or resetting of partic- ular items, or software installation. 1-5. Precautions for Service When performing inspection and service procedures, observe the following precautions t
ページ8に含まれる内容の要旨
4. Precautions for Dis/Reassembly Be sure to unplug the copier from the outlet before attempting to service the copier. The basic rule is not to operate the copier anytime during disassembly. If it is absolutely necessary to run the copier with its covers removed, use care not to allow your clothing to be caught in revolving parts such as the timing belt and gears. Before attempting to replace parts and unplug connectors, make sure that the power cord of the copier has been unplugged fr
ページ9に含まれる内容の要旨
8. Handling of the PC Drum ✽ Only for Products Not Employing an Imaging Cartridge. During Transportation/Storage Use the specified carton whenever moving or storing the PC Drum. The storage temperature is in the range between –20°C and +40°C. In summer, avoid leaving the PC Drum in a car for a long time. Handling Ensure that the correct PC Drum is used. Whenever the PC Drum has been removed from the copier, store it in its carton or protect it with a Drum Cloth. The PC Drum ex
ページ10に含まれる内容の要旨
C. Soak a small amount of either ethyl alcohol or iso- propyl alcohol into a clean, unused Dust-Free Cot- ton Pad which has been folded over into quarters. Now, wipe the surface of the PC Drum in one con- tinuous movement from its rear edge to its front edge and off its surface one to two times. ✽ Never move the Pad back and forth. 1076D003 D. Using the SAME face of the Pad, repeat the proce- dure explained in the latter half of step 3 until the entire surface of the PC Drum has been wiped.
ページ11に含まれる内容の要旨
ページ12に含まれる内容の要旨
CONTENTS 1. SAFETY PRECAUTIONS FOR INSPECTION AND SERVICE .......................P-1 1-1. Warning ....................................................................................................P-1 1-2. Caution .....................................................................................................P-3 1-3. Used Batteries Precautions ......................................................................P-5 1-4. Other Precautions ...................................................
ページ13に含まれる内容の要旨
ページ14に含まれる内容の要旨
GENERAL, MECHANICAL/ELECTRICAL
ページ15に含まれる内容の要旨
ページ16に含まれる内容の要旨
1. SPECIFICATIONS 1-1. Controller Specificationss Name Pi3505e, Pi3505e/PS Type Copier printer controller Di3510/Di3510f : 35ppm Di3010/Di3010f : 30ppm Print Speed Di2510/Di2510f : 25ppm Di2010/Di2010f : 20ppm (U.S. only) Printer Language PCL5e PCL6(XL ver.2.0) PostScript 3 Emulation (Pi3505e/PS) 16MB Compact Flash Card (Pi3505e) ROM 32MB Compact Flash Card (Pi3505e/PS) Additional 32 MB (Pi3505e) RAM Additional 128 MB (Pi3505e/PS) HDD 2.5 inch IDE interface (Option) Resolution 600 × 600 dpi Int
ページ17に含まれる内容の要旨
1-2. Supporting Client Specifications IBM PC and Compatible Computers CPU Pentium Memory 32MB or more OS Windows 98, Windows 98SE, Windows Me, Windows 2000, Windows XP, Windows NT 4.0 Should have sufficient memory and resources in the above Miscellaneous Windows and other applications used. Apple Macintosh Computers (Pi3505e/PS only) CPU Power PC Memory 64MB or more OS Mac OS 8.6, 9.2 or later Mac OS X 10.2 or later M-2
ページ18に含まれる内容の要旨
2. FUNCTION OVERVIEW OF CIRCUIT BOARDS The circuit boards used in the network interface have the functions described below. Circuit Board Name Function Overview CLAN circuit board Enables use of network functions by connecting to the MFB3 board. Printer Circuit Board Enables use of printer functions by connecting to the MFB3 board. Capacity: 32 MB (Pi3505e)/128 MB (Pi3505e/PS) Network Scan Circuit Enables use of network scan functions by connecting to the MFB3 Board board. Capacity: 128 MB
ページ19に含まれる内容の要旨
(3) LED indicators LED Color Status Meaning Lit The LAN is connected correctly. Data is not being sent or received. Green Off The copier has not been turned on. The LAN is not connected correctly. Flashing Data is being sent or received. Lit Operating at 100 Mbps Red Off Operating at 10 Mbps (4) Block Diagram MFB3 board interface connector USB connector 100 pin 4 pin Series B USB Address bus controller USB1.1b Data bus LAN connector 8 pin 100base-T Europe LAN Plus PCI bus controller trans- f
ページ20に含まれる内容の要旨
DIS/REASSEMBLY, ADJUSTMENT
