ページ1に含まれる内容の要旨
P3PC-1442-01EN
ページ2に含まれる内容の要旨
Contents Introduction................................................................................................................................................. 1 1. Preparations............................................................................................................................................ 4 1.1 Names of Component Parts .............................................................................................................................................
ページ3に含まれる内容の要旨
Introduction Thank you for purchasing the fi-590PRF Imprinter Regulatory Information option for fi-5900C Color Image Scanner. This guide explains how to install and use the imprinter. (For further details about the functions and operations of FCC declaration fi-5900C Image Scanner, refer to the “fi-5900C Image Scanner Operator’s Guide” included in fi-5900C Setup This equipment has been tested and found to comply CD-ROM.) with the limits for a Class A digital device, pursuant This g
ページ4に含まれる内容の要旨
Symbols Used In This Manual Bescheinigung des Herstellers / This manual uses the following symbols in addition Importeurs to warning indications Für den fi-590PRF wid folgendes bescheinigt: This symbol alerts operators to particularly ATTENTION • In Übereinsstimmung mit den Bestimmungen der important information. Be sure to read this information first before proceeding. EN45014(CE) funkentstört • Maschinenlärminformationsverordnung This symbol alerts the operator to useful advice o
ページ5に含まれる内容の要旨
Safety Precautions CAUTION FOLLOW THESE INSTRUCTIONS AND BE SURE TO HEED ALL WARNINGS AND CAUTIONS DESCRIBED The following describes important cautions. BELOW. Make sure that the scanner is installed on a flat, level WARNING surface and that none of its parts extend beyond the surface top, such as a desk or table. Do not touch the power plug with wet hands, since Do not install the scanner on unstable surfaces. doing so can cause electric shocks. Install the scanner on
ページ6に含まれる内容の要旨
1. Preparations 1.1 Names of Component Parts Open the Imprinter cover to see Imprinter (fi-590PRF) which is installed in the scanner (fi-5900C). Imprinter head Imprinter cover Print cartridge holder 4 |
ページ7に含まれる内容の要旨
2. Basic Operations 4. Open the imprinter cover. 2.1 Installing the Print Cartridge Mount the print cartridge as follows: Imprinter cover ATTENTION When installing or replacing the print cartridge, be careful not to insert it out of place. 1. Confirm that the scanner is turned off. 2. Hold the blue part located on the center of the hopper. 5. Move the Print cartridge holder to where the cartridge can be inserted easily. 3. Flip down the hopper gently. 6. Turn the
ページ8に含まれる内容の要旨
8. Remove protection tape from the print cartridge. 2.2 Operating Test After installing the imprinter, test to see if printing can be performed on the Offline Print Test mode. 1. While pressing the [Hopper Height] button ( or ) on the operator panel, switch on the scanner. Continue pressing on the [Hopper Height] button. ATTENTION Do not touch the metal part of the cartridge nor put the tape back again. 9. When the lever is closed, rotate the lever toward left to open before
ページ9に含まれる内容の要旨
Feeding direction 2.3 Positioning the Print Cartridge HINT Print test patterns To Position the print cartridge for printing: Test pattern 1 (Horizontal): ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`00000000 1. Open the imprinter cover. Test pattern 2 (Horizontal）: abcdefghijklmnopqrstuvwxyz{|}~ 00000000 Imprinter cover Test pattern 3 (Horizontal): !”#$%&'()*+,-./0123456789:;<=>?@00000000 Test pattern 4(Vertical): ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`00000000 Test pattern 5 (Vertical): abcdefg
ページ10に含まれる内容の要旨
2.4 How to Use the Paper Guide 2.5 Print Setup Use the Paper Guide to prevent paper jams due to curling of You can configure settings for the imprinter by using the the edges, as shown below. scanner driver dialog box. FUJITSU TWAIN driver (Example) Click [Option] button. In [Option] dialog box, choose [Imprinter (Endorser)] tab and specify the Imprinter settings. Feed direction Set the print cartridge to the right side and place the Paper Guide in the left area as shown in the illu
ページ11に含まれる内容の要旨
4. Turn the blue lever toward left and open the 2.6 Replacing the Print Cartridge cartridge holder. Make sure that you turn off the scanner power and unplug the power cable from the outlet. CAUTION If the cartridge replacement is done with power turned on, it may cause electric shock or imprinter failure. Replace the Print Cartridge as follows: ATTENTION ● When the following message appears, replace the Print Cartridge as soon as possible. 5. Take out the Print cartridge
ページ12に含まれる内容の要旨
8. Turn the lever on the print cartridge toward right to fix it. 9. Close the imprinter cover. 10. Reset the Ink Remain Counter. You must reset the Ink Remain Counter whenever you replace the print cartridge. On the [Start] menu, select [Programs]-[Scanner Utility for Microsoft Windows]-[Software Operation Panel]. Select the [Device Setting] tab. Click the [Clear] button at the [Remaining Ink (Pre)] button. The Ink remain counter will reset to 100%. 10 |
ページ13に含まれる内容の要旨
3. Daily Care 3.1 Cleaning the Print Cartridge 3.2 Cleaning the Imprinter Poor quality prints can occur due to blocked ink emission As the fi-590PRF prints the number on a document before holes in the nozzle. Leaving the imprinter unused for long reading operation, ink can spatter over the glass and paper periods can also cause emission holes to become blocked. path of the Upper transport unit, and vicinity of the print When the emission holes are blocked, clean the nozzle cartridge h
ページ14に含まれる内容の要旨
The cover is slowly opened. 5. Reinstall the print cartridge. 6. Hold the ADF cover with both hands and press it down slowly. 4. Wipe the following parts using a cloth moistened with Cleaner F1 or isopropyl alcohol. Press the ADF cover until it is fixed. HINT For details on cleaning the scanner, refer to “fi-5900C Operator’s Guide”. When closing the ADF, be sure nothing is left inside of the ADF. CAUTION Glasses of Upper transport unit and Transport Be careful not
ページ15に含まれる内容の要旨
4. Error Messages The following numbers or letters on the Function Number Display indicates a malfunction in the imprinter. Description: The Imprinter cover or ADF cover is open. How to solve: Close the Imprinter cover or ADF cover firmly. Description: The print cartridge is not installed. How to solve: Open the Imprinter cover and confirm that the print cartridge is installed correctly. Description: A problem occurred to the Imprinter. How to solve: Open the I
ページ16に含まれる内容の要旨
5. Specifications Item Specification Printing Method Thermal inkjet printing Print Timing Pre printing (front side) Printing Characters Alphabet : A to Z, a to z Numeric Characters : 0, 1 to9 Symbols : ! ” $ # % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _` { | } ¯ Maximum number of 40 characters (When using 8 digits counter: 43 characters) characters per line Print orientation Normal: 0º, 180º (horizontal orientation), 90º, 270º (vertical orie
ページ17に含まれる内容の要旨
Pre-printing area (front side) Feeding direction Item Specification Printing area Reference Head movable range Point Unit: mm * The document stains with ink when printing in the shaded areas (shown in the illustration). Therefore, correct printing operations in such areas are not guaranteed. Character position Vertical: ±4mm (at reference position) accuracy Horizontal: ±4mm (at reference position) Ambient condition Temperature: 10 to 35ºC (50 to 95ºF), Humidity: 20 to 80% Consuma
