ページ1に含まれる内容の要旨
BATTERY DRIVE, MICRO LINE THERMAL PRINTER
3” TYPE MECHANISM AND INTERFACE BOARD
FTP-633MCL400/FTP-623DCL002
n OVERVIEW
This battery driven, micro line thermal printer offers high speed
printing for 3-inch wide paper (70 mm). It is suitable for portable
equipment that requires compact, lightweight components.
In addition to the interface board, a driving LSI (MCU + Gate
Array) is also available.
n HIGHLIGHTS
• Driven by batteries (direct connect between thermal
head and batteries)
FTP-633MCL400
ページ2に含まれる内容の要旨
FTP-633MCL400/FTP-623DCL002 n DESIGNATION Item Part number Printer mechanism FTP-633MCL400* Interface board FTP-623DCL002 Micro Controller Unit FTP-623CU001 LSI Gate Array FTP-633GA101 *: Rear paper insertion type is available: FTP-633MCL402 n GENERAL SPECIFICATIONS Item Specifications Printing method Thermal-sensitive line dot method Dot structure 512 dots/line Dot pitch (Horizontal) 0.125 mm (8 dots/mm)—Dot density Dot pitch (Vertical) 0.125 mm (8 dots/mm)—Line feed pitch Effective printing ar
ページ3に含まれる内容の要旨
FTP-633MCL400/FTP-623DCL002 (Continued) Item Specifications 4.2 to 8.5 VDC (4 or 5 Ni-Cd or Ni-MH batteries, equivalent to 2 Li-ion) For print head Approximately 3.0 A (peak value, 7.2 V, 100% printing ratio) Operating 4.2 to 8.5 VDC (4 or 5 Ni-Cd or Ni-MH batteries, equivalent to 2 Li-ion) voltage For motor Average 0.7 A or less For logic 5 VDC ± 5%, 0.15 A Weight Mechanism: approximately 84 g. Interface board: approximately 60 g Printer mechanism Dimensions 85 (W) × 49 (D) × 20 (H) mm (exclud
ページ4に含まれる内容の要旨
60° 60° FTP-633MCL400/FTP-623DCL002 n DIMENSIONS Printer mechanism FTP-633MCL400 6.1 74.5 3.9 12.5 40 20 (3) (1) 3 5 Paper center 2 2.3 1.7 12 (14) 85 (2) Paper out angle (1): Head down 30 (2): Paper feed (Photo interrupter) Unit: mm (3): Head up lock Photo interrupter 70.2 (Paper insertion) Front and top insertion type FTP-633MCL402 6.1 74.5 3.9 12.5 40 20 (3) (1) 5 3 1.7 Paper center 2 12 (14) 85 (2) 3.1 Photo Paper out (Photo angle interrupter interrupter) (1): Head down 30 (2): Paper feed
ページ5に含まれる内容の要旨
FTP-633MCL400/FTP-623DCL002 Interface board 108.0 102.9 69.8 5.1 CN5 ø3.6 CN4 CN8 CN7 CN6 CN2 CN1 5.1 73.7 16.5 102.9 Height of devices side Height of solder side Unit: mm 5 90.2 10.0 46.5 17.6 5.1 4.6 5.1 10.0 13.3 5.1 42.5 85.1 6.0 1.6
ページ6に含まれる内容の要旨
FTP-633MCL400/FTP-623DCL002 n INTERFACE 1. Centronics standard (1) Connector Connector part number : FCN-215Q030-G/0 (Fujitsu Components) or equivalent Mating connector part number : FCN-217Q030-G/0 (Fujitsu Components) or equivalent FCN-214Q030-G/0 (Fujitsu Components) or equivalent FCN-215Q030-G/0 (Fujitsu Components) or equivalent (2) Connector pin assignment No. Signal I/O Contents No. Signal I/O Contents 1 PRSTB I Data strobe 2 PRSTB-RET — Connected to logic GND 3 PRDT0 I Data 0 4 PRDT0-RET
ページ7に含まれる内容の要旨
FTP-633MCL400/FTP-623DCL002 2. Bus interface (1) Connector Connector part number : FCN-215Q040-G/0 (Fujitsu Components) or equivalent Mating connector part number : FCN-217J040-G/0 (Fujitsu Components) or equivalent : FCN-214J040-G/0 (Fujitsu Components) or equivalent : FCN-215J040-G/0 (Fujitsu Components) or equivalent (2) Connector pin assignment No. Signal I/O Contents No. Signal I/O Contents 1 ALE O Address latch 2 BRD — Data read 3 BWR — Data write 4 READY — Data access ready 5 HACK — Hold
ページ8に含まれる内容の要旨
FTP-633MCL400/FTP-623DCL002 n CONNECTOR PIN ASSIGNMENT 1. Connector for logic power supply (CN1) Part number : B4B-XH-A-WHITE (J.S.T) or equivalent → P.C.B side Mating connector part number : XHP-4 (J.S.T) or equivalent → Cable side No. Signal I/O Contents No. Signal I/O Contents 1VCC — Power supply for logic (+5V) 2 GND — Logic ground 2. Connector for thermal head and motor power supply (CN2) Part number : B6B-XH-A-WHITE (J.S.T) or equivalent → P.C.B side Mating connector part number :
ページ9に含まれる内容の要旨
FTP-633MCL400/FTP-623DCL002 3. Connector for thermal head drive (CN7) Part number : 52030-2610 (Molex) or equivalent → P.C.B side No. Signal I/O Contents No. Signal I/O Contents 1 BAT — Power for head 2 BAT — Power for head 3 GND — Head ground 4 GND — Head ground 5 HD2 O Print data output 6 LAT O Printing data latch 7 HDV O Power for logic 8 HCLK O Printing transmitting clock 1, 2 1, 2 9 ENB8 * O Printing enable 10 ENB7 * — Printing enable 11 ENB6 O Printing enable 12 ENB5 O Printing enable 13
ページ10に含まれる内容の要旨
FTP-633MCL400/FTP-623DCL002 5. Connector for stepping motor drive (CN8) Part number : B10B-ZR (J.S.T) or equivalent → P.C.B side Mating connector part number : ZHR-10 (J.S.T) → Mechanism side No. Signal I/O Contents No. Signal I/O Contents 1 HUP I Head up detection 2 VCC — Power for switch 3 PINCH I Paper auto loading detection 4 SDV — Power for photointerrupter 5 SLED — Power for diode cathode 6 PES I Paper out detection 7 MT/B0 O Stepping motor coil excitation (B) 8 MT/B0 O Stepping
ページ11に含まれる内容の要旨
FTP-633MCL400/FTP-623DCL002 n PRINTING COMMANDS (CENTRONICS STANDARD INTERFACE) Name Command Contents Carriage return LF, CR Prints buffer data and return the line. Double width print set SO Sets the double width character. Power-down mode set DC2, DC3 Reduces the power consumption during standing by. Double width print reset DC4 Resets the double with character. ESC sequence entry ESC Indicates the start of an escape sequence formed by this code plus subsequent commands. Line space set ESC A +
ページ12に含まれる内容の要旨
FTP-633MCL400/FTP-623DCL002 n OPTIONS 1. Cable Name Part number Cable length For Centronics FTP-621Y202 500 mm Interface cable For Bus I/F FTP-621Y203 500 mm Power supply cable (A): for logic motor FTP-621Y401 300 mm Power supply cable (B): for thermal head FTP-621Y601 300 mm Head abnormal temperature detection cable FTP-621Y204 300 mm Europe Japan Fujitsu Component Limited Fujitsu Components Europe B.V. Diamantlaan 25 Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku 2132 WV Hoofd
