ページ1に含まれる内容の要旨
Read this Quick Setup Guide before using the printer.
Before you can use the printer, you must set up the hardware and install
the driver.
Step 1
Setting Up Your Printer
Step 2
Installing the Driver
Parallel
USB USB
® ®
page 12 page 14
Mac Mac
OS 8.6 – 9.2 OS X 10.1 –
page 16 10.2
page 17
Setup is Complete!
For the latest driver and to find the best solution for your problem or question, access the Brother
Solutions Center directly from the CD-ROM/Driver or go to http://solutions.brother.com
ページ2に含まれる内容の要旨
Safety Precautions To Use the Printer Safely Warning Note Hint User's Guide Indicates warnings that Indicates cautions that Indicates notes and Indicates reference to the must be observed to must be observed to use useful tips to remember User's Guide that is on prevent possible the printer properly or when using the printer. the CD-ROM we have personal injury. prevent damage to the supplied. printer. Warning There are high voltage electrodes inside the printer. Before replacing internal pa
ページ3に含まれる内容の要旨
Table of Contents Regulations ........................................................................................................... 2 ■ Getting Started Carton Components ............................................................................................. 4 Control Panel ........................................................................................................ 5 Supplied CD-ROM ...........................................................................................
ページ4に含まれる内容の要旨
Regulations Federal Communications Commission (FCC) Declaration of Conformity (For USA) Responsible Party: Brother International Corporation "EC" Declaration of Conformity 100 Somerset Corporate Boulevard P.O. Box 6911 Manufacture Bridgewater, NJ 08807-0911 Brother Industries Ltd., USA 15-1, Naeshiro-cho, Mizuho-ku, Telephone: (908) 704-1700 Nagoya 467-8561, Japan declares, that the products Plant Brother Corporation (Asia) Ltd., Product name: Laser Printer HL-1430, HL-1435 Brother Buji Nan L
ページ5に含まれる内容の要旨
FDA Regulations (100 to 120 volt Model Only) IT power system (For Norway only) This product is also designed for an IT power system with phase-to-phase U.S. Food and Drug Administration (FDA) has implemented regulations for voltage 230V. laser products manufactured on and after August 2, 1976. Compliance is mandatory for products marketed in the United States. One of the following Geräuschemission / Acoustic noise emission (for Germany labels on the back of the printer indicates compliance w
ページ6に含まれる内容の要旨
■ Getting Started Carton Components Printer 2 1 Face-down Output Tray Support Flap (Support Flap) 2 Face-down Output Tray (Top Output Tray) 1 3 Front Cover 4 Paper Tray 5 Manual Feed Paper Guides 7 6 Manual Feed Slot 7 Control Panel 3 6 4 5 Drum Unit Assembly (with Toner Cartridge CD-ROM Quick Setup Guide AC Power Cord included) (including User's Guide) Carton components may differ from one country to another. Save all packing materials and the printer carton. ■ The interface cable is not a s
ページ7に含まれる内容の要旨
Control Panel Cancel Printing Press the button one time and the printer will stop printing and eject the paper Button Reprinting When the Data LED is off, press and hold the button until all the LEDs light. The printer will reprint the last job. Drum Ready LED Paper Alarm Toner Data Button Printer LED Indications : Blinking : ON : OFF Warming Receiving Data Printer LED Sleep / OFF Ready Up Data Remaining Drum Drum Ready Ready Green Green Paper Alarm Alarm Toner Data Orange Orange Data No Pa
ページ8に含まれる内容の要旨
Supplied CD-ROM You can find a variety of information on the CD-ROM. ® 3 Mac OS 8.6 ® Mac OS X 10.1 to 9.2 Users to 10.2 Users 1 4 3 2 4 5 1 5 2 6 6 1 Initial Setup Instructional movie for printer setup and driver installation. 2 Install Software Installs the printer driver and utilities. 3 Documentation View the Printer User's Guide and Quick Setup Guide in PDF format. (Viewer included) 4 Brother Solutions Center The Brother Solutions Center (http://solutions.brother.com) is a one-stop resour
ページ9に含まれる内容の要旨
Setting Up Your Printer Step 1 1 Insert the CD-ROM into the CD-ROM Drive ® ® For Windows Users For Macintosh Users Do NOT connect the interface cable. Do NOT connect the interface cable. Connecting the interface cable is Connecting the interface cable is done when installing the driver. done when installing the driver. 1 Insert the CD-ROM into your CD-ROM 1 Insert the CD-ROM into your CD-ROM drive. Double-click the Start Here icon or drive. The opening screen will appear Start Here OS X ic
ページ10に含まれる内容の要旨
Setting Up Your Printer Step 1 2 Install the Drum Unit Assembly 4 Put the drum unit assembly into the printer. Do NOT connect the interface cable. Connecting the interface cable is done when installing the driver. 1 Open the front cover. Front cover 5 Close the front cover of the printer. 2 Unpack the drum unit assembly. Remove the protective part. Drum unit assembly Protective part 3 Rock it from side to side several times to distribute the toner evenly inside the assembly. 8
ページ11に含まれる内容の要旨
3 Load Paper in the Paper Tray 1 Pull the paper tray completely out of the 4 Put paper in the paper tray. printer. Check that the paper is flat in the tray and below the maximum paper mark. Up to here. Paper guide release lever 2 While pressing the paper guide release lever, slide the adjusters to fit the paper size. Check that the guides are firmly in the slots. 5 Put the paper tray firmly back in the printer. Paper guide release lever 3 Fan the stack of paper well to avoid paper jams and
ページ12に含まれる内容の要旨
Setting Up Your Printer Step 1 4 Print a Test Page 4 After the printer has finished warming up, Do NOT connect the interface cable. the Ready LED stops blinking and stays Connecting the interface cable is green. done when installing the driver. Extend the Support flap. Ready Paper Alarm Toner Data 1 Make sure that the printer power switch is off. 5 Press the control panel button. The printer prints a test page. Check that the test page has printed correctly. Drum Ready Paper Alarm Toner
ページ13に含まれる内容の要旨
Installing the Driver Step 2 Follow the appropriate instructions on this page for your operating system and interface cable. ® ® The screens for Windows in this Quick Setup Guide are based on Windows XP. ® ® The screens for Mac OS X in this Quick Setup Guide are based on Mac OS X 10.1. For USB Interface Cable Users............................Go to page 12 For Parallel Interface Cable Users.......................Go to page 14 For USB Interface Cable Users ® ■ Mac OS 8.6 to 9.2 Users .............
ページ14に含まれる内容の要旨
Installing the Driver Step 2 For USB Interface Cable Users 1. Installing the Driver and Connecting the Printer to Your PC 3 Select the USB interface. If the Found New Hardware Wizard appears on your PC, click the Cancel button. 4 Click the Install button. 1 Make sure the USB interface cable is NOT connected to the printer, and then begin installing the driver. If you have already connected the cable, remove it. 5 Click the Next button. Follow the on-screen instructions. 2 Click Connect th
ページ15に含まれる内容の要旨
6 When this screen appears, make sure the 2. Setting Your Printer as the printer power switch is on. Default Printer Connect the USB interface cable to your ® (For Windows 2000/XP Users PC, and then connect it to the printer. Click the Next button. Only) 1 Click Start and then Printers and Faxes. 2 Select the Brother HL-14XX series icon. 3 From the File menu, select Set as Default printer. 7 Click the Finish button. The setup is now complete. ® For Windows 98 / Me users: The Setup is no
ページ16に含まれる内容の要旨
Installing the Driver Step 2 For Parallel Interface Cable Users Connecting the Printer to Your PC and Installing the Driver 1 Click Connect the interface cable & 5 Turn on the printer power switch. Install the driver/utility from the Initial Setup menu. If the Found New Hardware Wizard 2 Select the Parallel interface. appears on your PC, click the Cancel button. 3 Turn off the printer power switch. 6 Click the Next button when the movie finishes. 4 Connect the parallel interface cable to y
ページ17に含まれる内容の要旨
7 Click the Install button. 8 Click the Next button. Follow the on-screen instructions. 9 Click the Finish button. The Setup is now complete. 15 Installing the Driver ® Setting Up Windows Your Printer Parallel
ページ18に含まれる内容の要旨
Installing the Driver Step 2 For USB Interface Cable Users ® For Mac OS 8.6 to 9.2 Users Installing the Driver & Connecting the Printer to your Macintosh 1 Click Connect the interface cable & 4 Connect the USB interface cable to your Install the driver/utility from the Initial Macintosh, and then connect it to the Setup menu. printer. Do not connect the USB cable to the keyboard USB Port or a non-powered USB Hub. 2 Follow the on-screen instructions, and restart your Macintosh. 5 Open the
ページ19に含まれる内容の要旨
For USB Interface Cable Users ® For Mac OS X 10.1 to 10.2 Users Installing the Driver & Connecting the Printer to your Macintosh 1 Click Connect the interface cable & 4 Connect the USB interface cable to your Install the driver/utility from the Initial Macintosh, and then connect it to the Setup menu. printer. Do not connect the USB cable to the keyboard USB Port or a non-powered USB Hub. 2 Click the Install button, and follow the on-screen instructions. 5 Select Applications from the Go me
ページ20に含まれる内容の要旨
Installing the Driver Step 2 For USB Interface Cable Users 7 Open the Print Center icon. A Select Quit Printer Center from the Printer Center menu. 8 Click the Add Printer... button. The setup is now complete. 9 Select USB. 0 Select HL-14XX series, and then click the Add button. 18
